YASKAWA GA700 Series Technical Manual page 828

12.8 H: Terminal Functions
■
H2-34: Comparator 2 Filter Time
No.
Name
(Hex.)
H2-34 Comparator 2 Filter Time
(159C)
■
H2-35: Comparator2 Protection Selection
No.
Name
(Hex.)
H2-35 Comparator2 Protection
Selection
(159D)
0 : Ramp to Stop
The drive ramps the motor to stop in the deceleration time. Fault relay output terminal MA-MC turns ON, and
MB-MC turns OFF.
1 : Coast to Stop
The output turns off and the motor coasts to stop. Fault relay output terminal MA-MC turns ON, and MB-MC
turns OFF.
2 : Fast Stop (Use C1-09)
The drive stops the motor in the deceleration time set in C1-09 [Fast Stop Time]. Fault relay output terminal MA-
MC turns ON, and MB-MC turns OFF.
3 : Alarm Only
The keypad shows CP2 and the drive continues operation at the current frequency reference.
Note:
The output terminal set for Alarm [H2-01 to H2-03 = 10] activates.
4 : Digital Output Only
■
H2-36: Comparator 1 Ineffective Time
No.
Name
(Hex.)
H2-36 Comparator 1 Ineffective
Time
(159E)
Note:
• After you enter a Run command and wait for the time set in this parameter, the drive will monitor operation and make sure that it is in
the Comparator 1 range until you enter the Stop command.
• When CP1 detection is disabled, the drive will activate the output terminal set for Comparator 1 [H2-xx = 66].
■
H2-37: Comparator 2 Ineffective Time
No.
Name
(Hex.)
H2-37 Comparator 2 Ineffective
Time
(159F)
Note:
• After you enter a Run command and wait for the time set in this parameter, the drive will monitor operation and make sure that it is in
the Comparator 2 range until you enter the Stop command.
• When CP2 detection is disabled, the drive will activate the output terminal set for Comparator 2 [H2-xx = 67].
■
H2-40: Mbus Reg 15E0h bit0 Output Func
No.
Name
(Hex.)
H2-40 Mbus Reg 15E0h bit0
Output Func
(0B58)
828
V/f CL-V/f OLV CLV AOLV
Sets the time constant that is applied to the primary delay filter used for the analog output of the
monitor selected with H2-26 [Comparator 2 Monitor Selection].
V/f CL-V/f OLV CLV AOLV
Sets drive operation when it detects CP2 [Comparator2 Limit Fault].
V/f CL-V/f OLV CLV AOLV
Sets the length of time that CP1 [Comparator1 Limit Fault] is disabled.
V/f CL-V/f OLV CLV AOLV
Sets the length of time that CP2 [Comparator2 Limit Fault] is disabled.
V/f CL-V/f OLV CLV AOLV
Sets the MFDO for bit 0 of MEMOBUS register 15E0 (Hex.).
Description
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
Description
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
Description
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
Description
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
Description
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
YASKAWA SIEPC71061705H GA700 Series Technical Manual
Default
(Range)
0.0s
(0.0 - 10.0 s)
Default
(Range)
4
(0 - 4)
Default
(Range)
0.0 s
(0.0 - 1000.0 s)
Default
(Range)
0.0 s
(0.0 - 1000.0 s)
Default
(Range)
F
(0 - 1FF)