List Of Devices - Mitsubishi Electric M800VW Series Manual

M800V/M80V Series PLC Development Manual
2 System Configuration of H/W

2.11 List of Devices

2.11 List of Devices
The device range in the following table is the default number of device points set in the project 1 when the multi-project setting
or the setting of the number of device points is not performed.
Device Device No.
X (*1) X0 to X1FFF
Y (*1) Y0 to Y1FFF
M M0 to M61439
F F0 to F2047
L L0 to L1023
SM SM0 to SM2047
V V0 to V511
SB SB0 to SB3FF
B B0 to BDFFF
SW SW0 to SW3FF
SD SD0 to SD2047
T0 to T2047
T
ST ST0 to ST127
C0 to C511
C
D D0 to D4095
R (*1) R0 to R32767
ZR0 to ZR13311
ZR (*1)
W W0 to W2FFF
Z0 to Z13/Z0 to Z9 (14 points/10
Z (*3)
N N0 to N7
P0 to P4095
P (*1)
K-32768 to K32767
K
K-2147483648 to K2147483647
H0 to HFFFF
H
H0 to HFFFFFFFF
E±1.17549435-38 to
E±3.40282347+38
E
E±2.2250738585072014 - 308 to
E±1.7976931348623157+308
$ 0 to 32 characters
(*1) These devices have designated applications. Do not use devices other than those corresponding to the input/output sig-
nals with the machine side (input/output signals of the remote I/O unit), even if it is an undefined vacant device.
(*2) Distinction of 10 ms timer and 100 ms timer is performed by command.
(10 ms timer is performed by OUTH command, 100 ms timer is performed by OUT command.)
(*3) For the Z device, the number of device points depends on the parameter setting.
(*4) The P device has two types of pointers (local and common), and the above points are the total points.
Unit
(8192 points) 1 bit
(8192 points) 1 bit
(61440 points) 1 bit
(2048 points) 1 bit
(1024 points) 1 bit
(2048 points) 1 bit
(512 points) 1 bit
(1024 points) 1 bit
(57344 points) 1 bit
(1024 points) 16 bits
(2048 points) 16 bits
(2048 points) 1 bit/16 bits
(128 points) 1 bit/16 bits
(512 points) 1 bit/16 bits
(4096 points) 16 bits/32 bits
(32768 points) 16 bits/32 bits
(13312 points) 16 bits/32 bits
(12288 points) 16 bits/32 bits
16 bits
points)
(8 points)
(4096 points)
Details
Input signal to PLC: Machine input, etc.
Output signal from PLC: Machine output, etc.
Temporary memory
Temporary memory, alarm message interface
Latch relay (back up memory)
Special relay
Edge relay
Special relay
Link relay
Special register
Special register
Timer (The variable/fixed boundary is set with a pa-
rameter.) (*2)
Integrated timer (100 ms unit)
Counter (The variable/fixed boundary is set with a
parameter.)
Data register (Register for calculation)
File register, CNC word interface
File register (Input/output signals with the PLC, ma-
chine input/output, etc.)
Link register
Address index
Master controller nesting level
Label for conditional jump, subroutine call command
(*4)
Decimal constant for 16-bit command
Decimal constant for 32-bit command
Hexadecimal constant for 16-bit command
Hexadecimal constant for 32-bit command
Hexadecimal constant for 16-bit command
Hexadecimal constant for 32-bit command
String constant
29 IB-1501614-B