Canon imagePRESS 1135 Series Service Manual page 813

Detail
Code Location Item
Code
E5BA 0003 61 Title Error in the spine bending motor (left) (M28) of the perfect
binder.
Description 1. When the spine bending closes, the spine bending close
of detection sensor (S61) is not ON within some specified time after
triggered
2. When the spine bending plate opens, the spine bending
close sensor (S61) is already OFF.
Measures 1. Replace the spine bending motor (left) (M28).
2. Replace the spine bending close sensor (S61).
3. Replace the slave controller PCB.
E5BA 0004 61 Title Error in the spine bending motor (left) (M28) of the perfect
binder.
Description 1. When the spine bending opens, the spine bending close
of detection sensor (S61) is not OFF within some specified time after
triggered
2. When the spine bending plate closes, the spine bending
close sensor (S61) is already ON.
Measures 1. Replace the spine bending motor (left) (M28).
2. Replace the spine bending close sensor (S61).
3. Replace the slave controller PCB.
E5BA 0005 61 Title Error in the spine bending motor (left) (M28) of the perfect
binder.
Description The spine bending home position sensor (left) (S60) and the
of detection spine bending close sensor (S61) is ON in the same time.
Measures 1. Replace the spine bending motor (left) (M28).
2. Replace the spine bending home position sensor (left)
(S60).
3. Replace the spine bending close sensor (S61).
4. Replace the slave controller PCB.
E5BA 8001 02 Title Error in the front estrangement motor
Description The front estrangement motor HP sensor does not turn ON.
of detection
Measures 1. Check the connector of the front estrangement motor HP
sensor (S102), and replace the sensor if necessary.
2. Replace the front estrangement motor (M103).
3. Replace the trimmer controller PCB (PCB1).
E5BA 8002 02 Title Error in the front estrangement motor
Description The front estrangement motor HP sensor does not turn OFF.
of detection
Measures 1. Check the connector of the front estrangement motor HP
sensor (S102), and replace the sensor if necessary.
2. Replace the front estrangement motor (M103).
3. Replace the trimmer controller PCB (PCB1).
7
Error Code > Error Code > Error Code Details
Description
7 Error Code > Error Code > Error Code Details
Detail
Code Location Item
Code
E5BA 8011 02 Title Error in the rear estrangement motor
Description The rear estrangement motor does not turn ON.
of detection
Measures 1. Check the connector of the rear estrangement motor HP
sensor (S104), and replace the sensor if necessary.
2. Replace the rear estrangement motor (M104).
3. Replace the trimmer controller PCB (PCB1).
E5BA 8012 02 Title Error in the rear estrangement motor
Description The rear estrangement motor does not turn OFF.
of detection
Measures 1. Check the connector of the rear estrangement motor HP
sensor (S104), and replace the sensor if necessary.
2. Replace the rear estrangement motor (M104).
3. Replace the trimmer controller PCB (PCB1).
E5BB 0001 61 Title Error in the spine bending motor (right) (M29) of the perfect
binder.
Description 1. When the spine bending plate opens, the spine bending
of detection home position sensor (right)(S66) is not ON within some
specified time after triggered .
2. When the spine bending plate closes, the spine bending
home position sensor (right) (S66) is already OFF.
Measures 1. Replace the spine bending motor (right)(M29).
2. Replace the spine home position sensor (right) (S66).
3. Replace the slave controller PCB.
E5BB 0002 61 Title Error in the spine bending motor (right) (M29) of the perfect
binder.
Description 1. When the spine bending plate closes, the spine bending
of detection home position sensor (right)(S66) is not OFF within some
specified time after triggered .
2. When the spine bending plate opens, the spine bending
home position sensor (right) (S66) is already ON.
Measures 1. Replace the spine bending motor (right)(M29).
2. Replace the spine home position sensor (right) (S66).
3. Replace the slave controller PCB.
E5BB 0003 61 Title Error in the spine bending motor (right) (M29) of the perfect
binder.
Description 1. When the spine bending plate closes, the spine bending
of detection pressure sensor (S69) is not ON within some specified
time after triggered .
2. When the spine bending plate opens, the spine bending
pressure sensor (S69) is already OFF.
Measures 1. Replace the spine bending motor (right)(M29).
2. Replace the spine bending pressure sensor (S69).
3. Replace the slave controller PCB.
7-81
Description
7-81