Canon imagePRESS 1135 Series Service Manual page 776

Detail
Code Location Item
Code
E530 8021 51 Title Error in lock of stack tray 2 alignment motor rear (M23) of the
stacker
Description Stack tray 2 alignment HP sensor rear (S40) failed to be OFF
of detection even though specified period of time has passed in the case
of initial operation to shift from HP to the standby position for
each paper
Measures 1. Check the connector of the stack tray 2 alignment HP
sensor rear (S40), and replace the sensor if necessary.
2. Replace the stack tray 2 alignment motor rear (M23).
3. Replace the slave controller PCB.
E530 8021 52 Title Error in lock of stack tray 2 alignment motor rear (M23) of the
2nd stacker
Description Stack tray 2 alignment HP sensor rear (S40) failed to be OFF
of detection even though specified period of time has passed in the case
of initial operation to shift from HP to the standby position for
each paper
Measures 1. Check the connector of the stack tray 2 alignment HP
sensor rear (S40), and replace the sensor if necessary.
2. Replace the stack tray 2 alignment motor rear (M23).
3. Replace the slave controller PCB.
E530 8022 51 Title Error in lock of stack tray 2 alignment motor rear (M23) of the
stacker
Description Stack tray 2 alignment HP sensor rear (S40) failed to be ON
of detection even though specified period of time has passed in the case
of initial operation to shift from the standby position for each
paper to HP
Measures 1. Replace the connector of the stack tray 2 alignment HP
sensor rear (S40).
2. Replace the stack tray 2 alignment motor rear (M23).
3. Replace the slave controller PCB.
E530 8022 52 Title Error in lock of stack tray 2 alignment motor rear (M23) of the
2nd stacker
Description Stack tray 2 alignment HP sensor rear (S40) failed to be ON
of detection even though specified period of time has passed in the case
of initial operation to shift from the standby position for each
paper to HP
Measures 1. Replace the connector of the stack tray 2 alignment HP
sensor rear (S40).
2. Replace the stack tray 2 alignment motor rear (M23).
3. Replace the slave controller PCB.
7
Error Code > Error Code > Error Code Details
Description
7 Error Code > Error Code > Error Code Details
Detail
Code Location Item
Code
E531 8001 02 Title a. Error in staple (Fin-AK)
b. Error in the staple motor (Fin-AG)
Description a. Staple position HP sensor does not come ON within 500
of detection msec after the staple motor starts operation.
b. The staple unit does not come off the staple HP sensor.
Measures a-1. Check the connector of the staple unit, and replace the
unit if necessary.
a-2. Check the connector of the staple position HP sensor,
and replace the sensor if necessary.
a-3. Replace the finisher controller PCB.
b-1. Check the connector of the staple unit, and replace the
unit if necessary.
b-2. Replace the finisher controller PCB.
E531 8002 02 Title a. Error in staple (Fin-AK)
b. Error in the staple motor (Fin-AG)
Description a. Staple position HP sensor does not go OFF within 500
of detection msec after the staple motor starts operation.
b. The staple HP sensor does nor detect the staple unit.
Measures a-1. Check the connector of the staple unit, and replace the
unit if necessary.
a-2. Check the connector of the staple position HP sensor,
and replace the sensor if necessary.
a-3. Replace the finisher controller PCB.
b-1. Check the connector of the staple unit, and replace the
unit if necessary.
b-2. Replace the finisher controller PCB.
E532 8000 02 Title Error in the stapler shift motor
Description Error in stapler shift motor at initialization is detected.
of detection
Measures 1. Check the connector of the stapler shift HP sensor (S107).
2. Check the connector of the staple shift motor (M107).
3. Replace the stapler shift HP sensor (S107).
4. Replace the Staple shift motor (M107).
5. Replace the finisher controller PCB.
7-44
Description
7-44