Canon imagePRESS 1135 Series Service Manual page 1108

COPIER> ADJUST> CCD
MTF2-M6 MTF value setting 6: main scan [Front]
Lv.1 Details Setting value for MTF filter coefficient calculation.
Input the value in the service label of the reader.
Use case When the reader controller PCB is replaced or RAM is cleared.
Adj/set/operate method 1) Enter the setting value and press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 20 to 85
Default value 50
Related service mode COPIER> FUNCTION> CCD> MTF-CLC
MTF2-M7 MTF value setting 7: main scan [Front]
Lv.1 Details Setting value for MTF filter coefficient calculation.
Input the value in the service label of the reader.
Use case When the reader controller PCB is replaced or RAM is cleared.
Adj/set/operate method 1) Enter the setting value and press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 20 to 85
Default value 50
Related service mode COPIER> FUNCTION> CCD> MTF-CLC
MTF2-M8 MTF value setting 8: main scan [Front]
Lv.1 Details Setting value for MTF filter coefficient calculation.
Input the value in the service label of the reader.
Use case When the reader controller PCB is replaced or RAM is cleared.
Adj/set/operate method 1) Enter the setting value and press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 20 to 85
Default value 50
Related service mode COPIER> FUNCTION> CCD> MTF-CLC
MTF2-M9 MTF value setting 9: main scan [Front]
Lv.1 Details Setting value for MTF filter coefficient calculation.
Input the value in the service label of the reader.
Use case When the reader controller PCB is replaced or RAM is cleared.
Adj/set/operate method 1) Enter the setting value and press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 20 to 85
Default value 50
Related service mode COPIER> FUNCTION> CCD> MTF-CLC
MTF2-S1 MTF value setting 1: sub scan [Front]
Lv.1 Details Setting value for MTF filter coefficient calculation.
Input the value in the service label of the reader.
Use case When the reader controller PCB is replaced or RAM is cleared.
Adj/set/operate method 1) Enter the setting value and press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 20 to 85
Default value 50
Related service mode COPIER> FUNCTION> CCD> MTF-CLC
8
Service Mode > COPIER > ADJUST (Adjustment Mode) > CCD
8 Service Mode > COPIER > ADJUST (Adjustment Mode) > CCD
COPIER> ADJUST> CCD
MTF2-S2 MTF value setting 2: sub scan [Front]
Lv.1 Details Setting value for MTF filter coefficient calculation.
Input the value in the service label of the reader.
Use case When the reader controller PCB is replaced or RAM is cleared.
Adj/set/operate method 1) Enter the setting value and press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 20 to 85
Default value 50
Related service mode COPIER> FUNCTION> CCD> MTF-CLC
MTF2-S3 MTF value setting 3: sub scan [Front]
Lv.1 Details Setting value for MTF filter coefficient calculation.
Input the value in the service label of the reader.
Use case When the reader controller PCB is replaced or RAM is cleared.
Adj/set/operate method 1) Enter the setting value and press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 20 to 85
Default value 50
Related service mode COPIER> FUNCTION> CCD> MTF-CLC
MTF2-S4 MTF value setting 4: sub scan [Front]
Lv.1 Details Setting value for MTF filter coefficient calculation.
Input the value in the service label of the reader.
Use case When the reader controller PCB is replaced or RAM is cleared.
Adj/set/operate method 1) Enter the setting value and press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 20 to 85
Default value 50
Related service mode COPIER> FUNCTION> CCD> MTF-CLC
MTF2-S5 MTF value setting 5: sub scan [Front]
Lv.1 Details Setting value for MTF filter coefficient calculation.
Input the value in the service label of the reader.
Use case When the reader controller PCB is replaced or RAM is cleared.
Adj/set/operate method 1) Enter the setting value and press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 20 to 85
Default value 50
Related service mode COPIER> FUNCTION> CCD> MTF-CLC
MTF2-S6 MTF value setting 6: sub scan [Front]
Lv.1 Details Setting value for MTF filter coefficient calculation.
Input the value in the service label of the reader.
Use case When the reader controller PCB is replaced or RAM is cleared.
Adj/set/operate method 1) Enter the setting value and press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 20 to 85
Default value 50
Related service mode COPIER> FUNCTION> CCD> MTF-CLC
8-165
8-165