Canon imagePRESS 1135 Series Service Manual page 777

Detail
Code Location Item
Code
E532 8001 02 Title a. Error in staple slide (Fin-AK)
b. Error in the stapler shift motor (Fin-AG)
Description a. Staple position HP sensor does not come ON within 500
of detection msec after the staple shift motor starts operation.
b. The staple unit does not come off the stapler shift HP
sensor.
Measures a-1. Check the connector of the staple shift motor, and replace
the motor if necessary.
a-2. Check the connector of the staple position HP sensor,
and replace the sensor if necessary.
a-3. Replace the finisher controller PCB.
b-1. Check the connector of the stapler shift HP sensor (S107).
b-2. Check the connector of the staple shift motor (M107).
b-3. Replace the stapler shift HP sensor (S107).
b-4. Replace the staple shift motor (M107).
b-5. Replace the finisher controller PCB.
E532 8002 02 Title a. Error in staple slide (Fin-AK)
b. Error in the stapler shift motor (Fin-AG)
Description a. Staple position HP sensor does not go OFF within 500
of detection msec after the staple shift motor starts operation.
b. The stapler shift HP sensor does not detect the staple unit.
Measures a-1. Check the connector of the staple shift motor, and replace
the motor if necessary.
a-2. Check the connector of the staple position HP sensor,
and replace the sensor if necessary.
a-3. Replace the finisher controller PCB.
b-1. Check the connector of the stapler shift HP sensor (S107).
b-2. Check the connector of the staple shift motor (M107).
b-3. Replace the stapler shift HP sensor (S107).
b-4. Replace the staple shift motor (M107).
b-5. Replace the finisher controller PCB.
E535 0001 02 Title Error in the swing guide motor
Description The swing guide does not come off the swing guide HP
of detection sensor.
Measures 1. Check the connector of the swing guide HP sensor (S110),
and replace the sensor if necessary.
2. Check the connector of the swing guide motor (M110), and
replace the motor if necessary.
3. Replace the finisher controller PCB.
E535 0002 02 Title Error in the swing guide motor
Description The swing guide HP sensor does not detect the swing guide.
of detection
Measures 1. Check the connector of the swing guide HP sensor (S110),
and replace the sensor if necessary.
2. Check the connector of the swing guide motor (M110), and
replace the motor if necessary.
3. Replace the finisher controller PCB.
7
Error Code > Error Code > Error Code Details
Description
7 Error Code > Error Code > Error Code Details
Detail
Code Location Item
Code
E535 0003 02 Title Error in the swing guide motor
Description The swing guide height detection sensor failed to be ON even
of detection though specified period of time has passed.
Measures 1. Check the connector of the swing guide height detection
sensor (S118), and replace the sensor if necessary.
2. Check the connector of the swing guide motor (M110), and
replace the motor if necessary.
3. Replace the finisher controller PCB.
E535 0004 02 Title Error in the swing guide motor
Description The swing guide height detection sensor failed to be OFF
of detection even though specified period of time has passed.
Measures 1. Check the connector of the swing guide height detection
sensor (S118), and replace the sensor if necessary.
2. Check the connector of the swing guide motor (M110), and
replace the motor if necessary.
3. Replace the finisher controller PCB.
E535 8001 02 Title Error in swing guide motor
Description Swing guide open sensor does not come ON within 2 sec
of detection after the swing guide motor starts operation.
Measures 1. Check the connector of the swing guide motor, and replace
the motor if necessary.
2. Check the connector of swing guide open sensor, and
replace the sensor if necessary.
3. Replace the finisher controller PCB.
E535 8002 02 Title Error in swing guide motor
Description Swing guide open sensor does not go OFF within 2 sec after
of detection the swing guide motor starts operation.
Measures 1. Check the connector of the swing guide motor, and replace
the motor if necessary.
2. Check the connector of swing guide open sensor, and
replace the sensor if necessary.
3. Replace the finisher controller PCB.
7-45
Description
7-45