Canon imagePRESS 1135 Series Service Manual page 1148

COPIER> ADJUST> FEED-ADJ
DUPDCL03 Dplx decrlr inlet mrgn adj (pikup deck3)
Lv.1 Details Use the paper on the POD middle deck as a target, adjust the
pressure level of the duplex decurler roller.
If the pressure level of the duplex decurler roller is increased, the
paper that pass the duplex path will have upper curl after both sides
repick up. If it becomes upper curl, failure image (specially thick
paper trailing edge density step) can be reduced.
The bigger the value is, the pressure level is increased.
Increase the level one by one while checking the improvement of the
image.
Use case When image failure (specially thick paper trailing edge density step)
occurs
Adj/set/operate method Input the setting value, and press OK.
Caution Jam might occur in a paper with feeding direction less than 240 mm
(jam code; 0112).
Display/adjust/set range 0 to 10
Appropriate target value 0
Default value 0
DUPDCL04 Dplx decrlr inlet mrgn adj (pikup deck4)
Lv.1 Details Use the paper on the POD lower deck as a target, adjust the
pressure level of the duplex decurler roller.
If the pressure level of the duplex decurler roller is increased, the
paper that pass the duplex path will have upper curl after both sides
repick up. If it becomes upper curl, failure image (specially thick
paper trailing edge density step) can be reduced.
The bigger the value is, the pressure level is increased.
Increase the level one by one while checking the improvement of the
image.
Use case When image failure (specially thick paper trailing edge density step)
occurs
Adj/set/operate method Input the setting value, and press OK.
Caution Jam might occur in a paper with feeding direction less than 240 mm
(jam code; 0112).
Display/adjust/set range 0 to 10
Appropriate target value 0
Default value 0
8
Service Mode > COPIER > ADJUST (Adjustment Mode) > FEED-ADJ
8 Service Mode > COPIER > ADJUST (Adjustment Mode) > FEED-ADJ
COPIER> ADJUST> FEED-ADJ
DUPDCL05 Dplx decrlr inlet mrgn adj (pikup deck5)
Lv.1 Details Use the paper on the secondary POD upper deck as a target, adjust
the pressure level of the duplex decurler roller.
If the pressure level of the duplex decurler roller is increased, the
paper that pass the duplex path will have upper curl after both sides
repick up. If it becomes upper curl, failure image (specially thick
paper trailing edge density step) can be reduced.
The bigger the value is, the pressure level is increased.
Increase the level one by one while checking the improvement of the
image.
Use case When image failure (specially thick paper trailing edge density step)
occurs
Adj/set/operate method Input the setting value, and press OK.
Caution Jam might occur in a paper with feeding direction less than 240 mm
(jam code; 0112).
Display/adjust/set range 0 to 10
Appropriate target value 0
Default value 0
DUPDCL06 Dplx decrlr inlet mrgn adj (pikup deck6)
Lv.1 Details Use the paper on the secondary POD middle deck as a target, adjust
the pressure level of the duplex decurler roller.
If the pressure level of the duplex decurler roller is increased, the
paper that pass the duplex path will have upper curl after both sides
repick up. If it becomes upper curl, failure image (specially thick
paper trailing edge density step) can be reduced.
The bigger the value is, the pressure level is increased.
Increase the level one by one while checking the improvement of the
image.
Use case When image failure (specially thick paper trailing edge density step)
occurs
Adj/set/operate method Input the setting value, and press OK.
Caution Jam might occur in a paper with feeding direction less than 240 mm
(jam code; 0112).
Display/adjust/set range 0 to 10
Appropriate target value 0
Default value 0
8-205
8-205