Canon imagePRESS 1135 Series Service Manual page 806

Detail
Code Location Item
Code
E5AF 8072 02 Title The shift motor (M08) of the two-knife booklet trimmer is
remained at the home position: conveyer retaining roller
Description The retaining roller home position sensor (PI14) is not turned
of detection OFF.
Measures 1. Check the connector.
2. Replace the sensor.
3. Replace the motor.
E5AF 8085 02 Title Invalid EEPROM data of the top/bottom edge trimmer
Description Either the initial setting of EEPROM which stores each home
of detection position value is not made, or data is damaged. This error
normally occurs when replacing the top/bottom edge trimmer
controller PCB.
Measures Initialize EEPROM by the following procedure.
1. Turn OFF the top/bottom edge trimmer.
2. Set the DSW1 No. 2 of the top/bottom edge trimmer
controller PC to ON.
3. Turn ON the power. (Initialization of EEPROM is executed.)
4. Turn OFF the power after a few seconds.
5. Set the DSW1 No.2 to OFF.
6. Turn ON the power, and check that no error occurs.
7. Set each home position value described in the home
position seal affixed to the top/bottom edge trimmer from
the LCD panel of the fore edge trimmer.
E5AF 8086 02 Title Failure in EEPROM writing of the two-knife booklet trimmer
Description There was a failure in EEPROM writing
of detection
Measures Replacement of the controller PCB
E5AF 8087 02 Title Failure in EEPROM checksum of the two-knife booklet
trimmer
Description There was a failure in EEPROM checksum
of detection
Measures Replacement of the controller PCB
E5AF 8096 02 Title The stepping motor of the two-knife booklet trimmer has not
completed returning to home position.
Description The paper stack information or the booklet delivery command
of detection of the booklet trimmer was received while the operation-start
command was not received.
Measures 1. Check the connector.
2. Replace the motor.
7
Error Code > Error Code > Error Code Details
Description
7 Error Code > Error Code > Error Code Details
Detail
Code Location Item
Code
E5AF 8097 02 Title The stepping motor of the two-knife booklet trimmer has not
completed shifting to the specified position.
Description The booklet delivery command of the booklet trimmer was
of detection received while the paper stack information was not received
after having received the operation-start command to execute
guide initialization.
Measures 1. Check the connector.
2. Replace the motor.
E5AF 80A8 02 Title Failure in command transmission retry of the two-knife
booklet trimmer
Description There have been 4 consecutive retries of command
of detection transmission to the booklet trimmer
Measures Replacement of the controller PCB
E5AF 80A9 02 Title Failure in command NAK reception count of the two-knife
booklet trimmer
Description NAK has been received for 5 times or more for the same
of detection command that was sent to the booklet trimmer
Measures Replacement of the controller PCB
E5AF 80AA 02 Title Error in interlock safety unit (A100) of the two-knife booklet
trimmer
Description There was a failure in the interlock safety unit (A100)
of detection
Measures
E5AF 80AB 02 Title Error in switching power supply (G00) of the two-knife booklet
trimmer
Description Alarm signal was received from the switching power supply
of detection (G00)
Measures
E5AF 80AC 02 Title Error in interlock (K01) of the two-knife booklet trimmer
Description K01 was not cut by opening the upper surface cover although
of detection K02 was cut.
Measures
E5AF 80AD 02 Title Error in interlock (K02) of the two-knife booklet trimmer
Description K02 was not cut by opening the upper surface cover although
of detection K01 was cut.
Measures
7-74
Description
T-7-7
7-74