Canon imagePRESS 1135 Series Service Manual page 772

Detail
Code Location Item
Code
E514 8001 02 Title a. Error in assist operation (Fin-AK)
b. Error in the gripper base motor (Fin-AG)
Description a. Assist HP sensor does not come ON within 5 sec after the
of detection assist motor starts operation.
b. The gripper does not come off the gripper base rear sensor
(S117).
Measures a-1. Check the connector of assist HP sensor.
a-2. Check the connector of assist motor.
a-3. Replace the assist HP sensor.
a-4. Replace the assist motor.
a-5. Replace the finisher controller PCB.
b-1. Check the connector of the gripper base rear sensor
(S117) and gripper base motor (M116).
b-2. Replace the gripper base rear sensor (S117).
b-3. Replace the gripper base motor (M116).
b-4. Replace the finisher controller PCB.
E514 8002 02 Title a. Error in assist operation (Fin-AK)
b. Error in the gripper base motor (Fin-AG)
Description a. Assist HP sensor does not go OFF within 5 sec after the
of detection assist motor starts operation.
b. The gripper base rear sensor (S117) dose not detect the
gripper.
Measures a-1. Check the connector of assist HP sensor.
a-2. Check the connector of assist motor.
a-3. Replace the assist HP sensor.
a-4. Replace the assist motor.
a-5. Replace the finisher controller PCB.
b-1. Check the connector of the gripper base rear sensor
(S117) and gripper base motor (M116).
b-2. Replace the gripper base rear sensor (S117).
b-3. Replace the gripper base motor (M116).
b-4. Replace the finisher controller PCB.
E514 8003 02 Title Error in the gripper motor
Description The gripper does not come off the gripper HP sensor.
of detection
Measures 1. Check the connector of the gripper HP sensor (S140), and
replace the sensor if necessary.
2. Check the connector of the gripper motor (M117), and
replace the motor if necessary.
3. Replace the finisher controller PCB.
7
Error Code > Error Code > Error Code Details
Description
7 Error Code > Error Code > Error Code Details
Detail
Code Location Item
Code
E514 8004 02 Title Error in the gripper motor
Description The gripper HP sensor does not detect the gripper.
of detection
Measures 1. Check the connector of the gripper HP sensor (S140), and
replace the sensor if necessary.
2. Check the connector of the gripper motor (M117), and
replace the motor if necessary.
3. Replace the finisher controller PCB.
E514 8005 02 Title Error in the gripper motor
Description The gripper does not come off the position sensor.
of detection
Measures 1. Check the connector of the gripper position sensor (S115),
and replace the sensor if necessary.
2. Check the connector of the gripper motor (M117), and
replace the motor if necessary.
3. Replace the finisher controller PCB.
E514 8006 02 Title Error in the gripper motor
Description The gripper position sensor does not detect the gripper.
of detection
Measures 1. Check the connector of the gripper position sensor (S115),
and replace the sensor if necessary.
2. Check the connector of the gripper motor (M117), and
replace the motor if necessary.
3. Replace the finisher controller PCB.
E518 0001 02 Title Error in folding feed motor (M11) of paper folding unit
Description The lock signal is detected ON for certain consecutive period
of detection of time since the folding feed motor started to be driven.
Measures Check the connector of the folding feed motor (M11)/ replace
the motor if necessary.
E518 8001 02 Title Error in folding feed motor lock
Description Folding feed motor is locked.
of detection
Measures Replace the folding feed motor (M11).
E523 8001 51 Title Error in lock of lead-in shift motor (M30) of the stacker
Description The lead-in shift HP sensor (S42) failed to be OFF even
of detection though specified period of time has passed in the case of
initial operation to shift from the home position to lead-in
position for each paper.
Measures 1. Check the connector of the lead-in shift HP sensor (S42),
and replace the sensor if necessary.
2. Replace the lead-in shift motor (M30).
3. Replace the slave controller PCB.
7-40
Description
7-40