Canon imagePRESS 1135 Series Service Manual page 1163

■ PART-CHK
COPIER> FUNCTION> PART-CHK
CL Specify operation clutch
Lv.1 Details Specify the transfer cleaning clutch (CL1) to operate.
Use case At the time of replacement of the clutch / operation check
Adj/set/operate method Enter "1" and press the OK key.
Display/adjust/set range 1: Transfer cleaning clutch (CL1)
During operation: ACTIVE, At termination: OK!
Default value 0
Related service mode COPIER> FUNCTION> PART-CHK> CL-ON
CL-ON Operation check of clutch
Lv.1 Details Start operation of the transfer cleaning clutch (CL1).
During operation, ON/OFF is repeated with an interval of 3 seconds.
Use case At the time of replacement of the clutch / operation check
Adj/set/operate method 1) Drive the ITB and drum (COPIER> FUNCTION> MISC-P> MAIN-
DRV)
2) Select the item and press the OK key.
3) Check the gear of the transfer cleaning assembly.
Display/adjust/set range During operation: ACTIVE, At termination: OK!
Default value 0
Required time Approx. 1 minute
Related service mode COPIER> FUNCTION> MISC-P> MAIN-DRV
COPIER> FUNCTION> PART-CHK> CL
Supplement/memo Remove the cover so that the clutch can be checked visually.
8
Service Mode > COPIER > FUNCTION (Operation / Inspection Mode) > PART-CHK
8 Service Mode > COPIER > FUNCTION (Operation / Inspection Mode) > PART-CHK
COPIER> FUNCTION> PART-CHK
FAN Specify operation fan
Lv.1 Details Specify the fan to operate.
Use case At the time of replacement of the fan / operation check
Adj/set/operate method Enter the value and press the OK key.
Display/adjust/set range 1 to 66
1: Developing cooling fan (FM1)
2: Pre-primary transfer suction fan (FM2)
3: Primary suction fan (FM3), 4: Primary exhaust fan (FM4)
5: Developing assembly cooling fan (FM5), 6, 7: Not used
8: Fixing assembly heat exhaust fan 1 (FM8)
9: Fixing assembly heat exhaust fan 2 (FM9)
10: Fixing sheet cooling fan 1 (FM10)
11: Fixing sheet cooling fan 2 (FM11), 12: Not used
13: Pre-fixing feed exhaust fan (FM13)
14: Fixing sheet cooling fan 3 (FM14)
15: Power supply cooling fan 1 (FM15)
16: Power supply cooling fan 2 (FM16), 17: Not used
18: Laser scanner cooling fan (FM18)
19: Pre-fixing feed fan (front) (FM19)
20: Pre-fixing feed fan (rear) (FM20)
21: Internal delivery cooling fan (FM21)
22: Pre-primary transfer exhaust fan (FM22), 23 to 24: Not used
25: Fixing duct suction fan (FM25), 26: Not used
27: Fixing feed motor driver cooling fan (FM27)
28: Fixing lower roller cooling fan 1 (FM28)
29: Fixing lower roller cooling fan 2 (FM29)
30: Fixing lower roller cooling fan 3 (FM30)
31: Fixing lower roller cooling fan 4 (FM31)
32: Fixing lower roller cooling fan 5 (FM32), 33 to 44: Not used
45: Power supply cooling fan 3 (FM45)
46: Toner feed pipe cooling fan (FM46), 47 to 52: Not used
53: Hopper cooling fan 1 (FM53), 54: Hopper cooling fan 2 (FM54)
55: Hopper cooling fan 3 (FM55), 56: Delivery upper fan 1 (FM56)
57: Delivery upper fan 2 (FM57), 58: Delivery lower fan 1 (FM58)
59: Delivery lower fan 2 (FM59)
60: Pre-registration cooling fan (FM60), 61, 62: Not used
63: Fixing sensor fan (FM63), 64: Power supply cooling fan4 (FM64)
65: Fixing sheet cooling fan 3 lower (FM65)
66: Reverse delivery motor cooling fan (FM66)
During operation: ACTIVE, At termination: OK!
Default value 1
Related service mode COPIER> FUNCTION> PART-CHK> FAN-ON
FAN-ON Operation check of fan
Lv.1 Details Start operation of the fan specified by FAN.
Use case At the time of replacement of the fan / operation check
Adj/set/operate method Select the item and press the OK key.
Required time 1 minute
Related service mode COPIER> FUNCTION> PART-CHK> FAN
8-220
8-220