Canon imagePRESS 1135 Series Service Manual page 1210

COPIER > OPTION > FEED-SW
PFIX-P-2 Pstn set prefixing feed assy: 64-79 g/m2
Lv.1 Details Lowering standby position of the pre-fixing feeding assembly to
secure feeding stability.
This mode only applies to LTR size or smaller paper with grammage
of 64 to 79 g/m2.
Use case - In the case of pre-fixing corner bend between secondary transfer
and the fixing
- In the case of big pre-fixing upper curl on the 1st side that prevents
the paper's leading edge from entering into the fixing roller nip,
resulting in inner delivery sensor delay jam
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF and then ON the main power supply.
Caution There should be no pre-fixing corner bend or inner delivery sensor
delay jam.
Display/adj/set range 0 to 1
0: Upper position, 1: Lower position
Default value 0
PFIX-P-3 Pstn set prefixing feed assy: 80-105g/m2
Lv.1 Details Lowering standby position of the pre-fixing feeding assembly to
secure feeding stability.
This mode only applies to LTR size or smaller paper with grammage
of 80 to 105 g/m2.
Use case - In the case of pre-fixing corner bend between secondary transfer
and the fixing
- In the case of big pre-fixing upper curl on the 1st side that prevents
the paper's leading edge from entering into the fixing roller nip,
resulting in inner delivery sensor delay jam
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF and then ON the main power supply.
Caution There should be no pre-fixing corner bend or inner delivery sensor
delay jam.
Display/adj/set range 0 to 1
0: Upper position, 1: Lower position
Default value 0
8
Service Mode > COPIER > OPTION (Mechanical specifications Setting Mode) > FEED-SW
8 Service Mode > COPIER > OPTION (Mechanical specifications Setting Mode) > FEED-SW
COPIER > OPTION > FEED-SW
PFIX-P-4 Pstn set prefixing feed assy:106-128g/m2
Lv.1 Details Lowering standby position of the pre-fixing feeding assembly to
secure feeding stability.
This mode only applies to LTR size or smaller paper with grammage
of 106 to 128 g/m2.
Use case - In the case of pre-fixing corner bend between secondary transfer
and the fixing
- In the case of big pre-fixing upper curl on the 1st side that prevents
the paper's leading edge from entering into the fixing roller nip,
resulting in inner delivery sensor delay jam
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF and then ON the main power supply.
Caution There should be no pre-fixing corner bend or inner delivery sensor
delay jam.
Display/adj/set range 0 to 1
0: Upper position, 1: Lower position
Default value 0
PFIX-P-5 Pstn set prefixing feed assy:129-150g/m2
Lv.1 Details Lowering standby position of the pre-fixing feeding assembly to
secure feeding stability.
This mode only applies to LTR size or smaller paper with grammage
of 129 to 150 g/m2.
Use case - In the case of pre-fixing corner bend between secondary transfer
and the fixing
- In the case of big pre-fixing upper curl on the 1st side that prevents
the paper's leading edge from entering into the fixing roller nip,
resulting in inner delivery sensor delay jam
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF and then ON the main power supply.
Caution There should be no pre-fixing corner bend or inner delivery sensor
delay jam.
Display/adj/set range 0 to 1
0: Upper position, 1: Lower position
Default value 0
8-267
8-267