Canon imagePRESS 1135 Series Service Manual page 779

Detail
Code Location Item
Code
E537 8021 52 Title Error in lock of stack tray 2 alignment motor front (M27) of the
2nd stacker
Description Stack tray 1 alignment HP sensor front (S48) failed to be OFF
of detection even though specified period of time has passed in the case
of initial operation to shift from HP to the standby position for
each paper
Measures 1. Check the connector of the stack tray 2 alignment HP
sensor front (S51), and replace the sensor if necessary.
2. Replace the stack tray 2 alignment motor front (M27).
3. Replace the slave controller PCB.
E537 8022 51 Title Error in lock of stack tray 2 alignment motor front (M27) of the
stacker
Description Stack tray 1 alignment HP sensor front (S48) failed to be ON
of detection even though specified period of time has passed in the case
of initial operation to shift from the standby position for each
paper to HP
Measures 1. Replace the stack tray 2 alignment HP sensor front (S51).
2. Replace the stack tray 2 alignment motor front (M27).
3. Replace the slave controller PCB.
E537 8022 52 Title Error in lock of stack tray 2 alignment motor front (M27) of the
2nd stacker
Description Stack tray 1 alignment HP sensor front (S48) failed to be ON
of detection even though specified period of time has passed in the case
of initial operation to shift from the standby position for each
paper to HP
Measures 1. Replace the stack tray 2 alignment HP sensor front (S51).
2. Replace the stack tray 2 alignment motor front (M27).
3. Replace the slave controller PCB.
E539 8001 02 Title Error in delivery angle adjustment motor (HP sensor delay)
Description HP sensor does not come ON within 5 sec after the operation
of detection start.
Measures 1. Check the connector of the delivery angle HP sensor.
2. Check the connector of the delivery angle adjustment
motor.
3. Replace the delivery angle HP sensor.
4. Replace the delivery angle adjustment motor.
5. Replace the finisher controller PCB.
7
Error Code > Error Code > Error Code Details
Description
7 Error Code > Error Code > Error Code Details
Detail
Code Location Item
Code
E539 8002 02 Title Error in delivery angle adjustment motor (HP sensor
stationary)
Description HP sensor does not go OFF within 5 sec after the operation
of detection start.
Measures 1. Check the connector of the delivery angle HP sensor.
2. Check the connector of the delivery angle adjustment
motor.
3. Replace the delivery angle HP sensor.
4. Replace the delivery angle adjustment motor.
5. Replace the finisher controller PCB.
E540 0013 02 Title Error in the tray 1 shift motor
Description The swing guide safety switch (front/rear) is turned ON.
of detection
Measures 1. Check the connector of the swing guide safety switch (front/
rear) (SW102/SW104).
2. Check the connector of the staple position switch (SW103).
3. Replace the swing guide safety switch (front/rear) (SW102/
SW104).
4. Replace the staple position switch (SW103).
5. Replace the swing guide solenoid (SL101).
6. Replace the tray 1 shift motor (M105).
7. Replace the finisher controller PCB.
E540 8001 02 Title a. Error in tray A (upper tray) (Fin-AK)
b. Error in the tray 1 shift motor (Fin-AG)
Description a. Tray A rotation sensor does not come ON within 300 msec
of detection after the tray A up/down motor starts operation.
b. The tray 1 does not come off the tray 1 area sensor at the
same area.
Measures a-1. Check the connector of the tray A rotation sensor.
a-2. Check the connector of the tray A up/down motor.
a-3. Replace the tray A rotation sensor.
a-4. Replace the tray A up/down motor.
a-5. Replace the finisher controller PCB.
b-1. Check the connectors of the tray 1 area sensors (S122/
S123/S124), and replace the sensors if necessary.
b-2. Check the connector of the tray 1 shift motor (M105), and
replace the motor if necessary.
b-3. Replace the finisher controller PCB.
7-47
Description
7-47