Canon imagePRESS 1135 Series Service Manual page 1166

COPIER> FUNCTION> CLEAR
MN-CON RAM clear of main CON PCB SRAM board
Lv.1 Details Clear the RAM data of the main controller PCB SRAM board.
All data on the SRAM board is initialized.
Use case At the time of clearing of the RAM data of the main controller PCB
SRAM board
Adj/set/operate method 1) Select the item and press the OK key.
The machine is automatically rebooted.
2) Turn OFF/ON the main power.
Caution • Inform the user that all images in BOX will be deleted and receive
approval about it.
• Since the file management information is initialized, images on the
HDD cannot be also read.
• Before execution of this item, be sure to output the service mode
setting value by P-PRINT. After execution, enter necessary setting
values.
• The RAM data is cleared after the main power is turned OFF/ON.
Related service mode COPIER> FUNCTION> MISC-P> P-PRINT
CARD Clear of card ID-related data
Lv.1 Details Clear the data related to the card ID (department).
Use case At the time of clearing of the data related to the card ID
Adj/set/operate method 1) Select the item and press the OK key.
2) Turn OFF/ON the main power.
Caution The data is cleared after the main power is turned OFF/ON.
ALARM Clear of alarm log
Lv.1 Details Clear the alarm log.
Use case At the time of clearing of the alarm log
Adj/set/operate method 1) Select the item and press the OK key.
2) Turn OFF/ON the main power.
Caution The alarm log is cleared after the main power is turned OFF/ON.
SND-STUP Clear setting name of send read setting
Lv.2 Details Clear the name of the send scanning setting.
Use case At the time of switching of the language setting
Adj/set/operate method Select the item and press the OK key.
8
Service Mode > COPIER > FUNCTION (Operation / Inspection Mode) > CLEAR
8 Service Mode > COPIER > FUNCTION (Operation / Inspection Mode) > CLEAR
COPIER> FUNCTION> CLEAR
CA-KEY Delete CA certificate and key pair
Lv.2 Details Simultaneously delete the CA certificate and key pair which are
additionally registered by the user.
Use case At the time of replacement/discarding of the device by a service
person
Adj/set/operate method 1) Select the item and press the OK key.
2) Check that OK is displayed.
3) Turn OFF/ON the main power.
Caution • Unless this item is executed at the time of replacement/discarding
of the device, the CA certificate and key pair which are additionally
registered by the user remain in the HDD, which is a problem in
terms of security.
• Do not execute this item carelessly because the CA certificate
and key pair which are additionally registered are deleted when
it is executed. If they are deleted mistakenly, they need to be
again registered by the user. If no CA certificate and key pair are
additionally registered, the machine condition becomes the same
as the one at the time of factory shipment, so there is no problem.
• When NG is displayed in 2), there is a possibility that deletion was
not executed. In this case, surely execute deletion by initializing
the HDD, etc.
Display/adjust/set range When operation finished normally: OK, When operation failed: NG
Supplement/memo • The CA certificate is used in the MEAP application with the
function of E-RDS and SSL client connection, and the key pair is
used in the IPP, RUI, MEAP SSL function.
• When the main power is turned OFF/ON, the CA certificate and
key pair which were registered at the time of factory shipment
are decompressed from the archive (/BOOTDEV/KCMNG), and
become available in the E-RDS/SSL function.
LANG-ERR Clear of language-related error
Lv.1 Details Clear the language-related error.
When the language-related error occurred after switched to the
language other than the default language, the setting recovers and
returns to the default language.
Use case When the language-related error occurred at the time of switching of
the language
Adj/set/operate method Select the item and press the OK key.
8-223
8-223