Canon imagePRESS 1135 Series Service Manual page 1193

COPIER > OPTION > IMG-FIX
FX-LVL08 Set of fixing ability (POD3 upper deck)
Lv.1 Details Setting for fixing performance.
Selecting the mode with priority on fixing performance makes the
paper in the deck to be fed with the sequence to improve fixing
performance (increasing fixing temperature + drop in throughput).
Perform this mode separately for each deck.
Use case In the case of low fixing performance
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 1
0: Standard mode, 1: Mode with priority on fixing performance
Default value 0
Supplement/memo Following can be applied at the same time: COPIER> OPTION>
IMG-FIX> OHP-TEMP
FX-LVL09 Set of fixing ability (POD3 middle deck)
Lv.1 Details Setting for fixing performance.
Selecting the mode with priority on fixing performance makes the
paper in the deck to be fed with the sequence to improve fixing
performance (increasing fixing temperature + drop in throughput).
Perform this mode separately for each deck.
Use case In the case of low fixing performance
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 1
0: Standard mode, 1: Mode with priority on fixing performance
Default value 0
Supplement/memo Following can be applied at the same time: COPIER> OPTION>
IMG-FIX> OHP-TEMP
FX-LVL10 Set of fixing ability (POD3 lower deck)
Lv.1 Details Setting for fixing performance.
Selecting the mode with priority on fixing performance makes the
paper in the deck to be fed with the sequence to improve fixing
performance (increasing fixing temperature + drop in throughput).
Perform this mode separately for each deck.
Use case In the case of low fixing performance
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 1
0: Standard mode, 1: Mode with priority on fixing performance
Default value 0
Supplement/memo Following can be applied at the same time: COPIER> OPTION>
IMG-FIX> OHP-TEMP
8
Service Mode > COPIER > OPTION (Mechanical specifications Setting Mode) > IMG-FIX
8 Service Mode > COPIER > OPTION (Mechanical specifications Setting Mode) > IMG-FIX
COPIER > OPTION > IMG-FIX
FX-JAM-W Adj fix web slnd drve times at jam recvr
Lv.1 Details Adjusting the number of drives for fixing web solenoid in the case
that the fixing roller temperature is 180 deg C with jam recovery
sequence.
Use case Upon request from the user to shorten the jam recovery sequence.
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 100
Unit 1 time
Default value 70
FX-JAM-I Adj of idling time at jam recovery
Lv.1 Details Adjusting the time for idle rotation after the fixing cleaning web is
taken up with jam recovery sequence.
The external heat roller and the pressure roller are disengaged
(separated) from the fixing roller during idle rotation.
Use case Upon request from the user to shorten the jam recovery sequence.
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 60
Unit 1 second
Default value 30
FIX-ENV1 Set of fixing mode: Thin/Plain PP
Lv.1 Details To set the fixing performance/productivity for thin paper of 105 g/m2
or less and plain paper.
When 0 is specified, auto mode is enabled.
From 1 to 3, as the smaller value is set, priority is given to
productivity and the greater value is set, priority is given to fixing
performance.
When 4 is specified, priority is given to productivity in case of 15 deg
C or more as well as setting value 1 (fixing mode 1) and priority is
given to fixing performance in case of less than 15 deg C as well as
setting value 3 (fixing mode 3).
Use case When changing the fixing performance or productivity during auto
control.
Adj/set/operate method Enter the setting value and press the OK key.
Display/adj/set range 0 to 4
0: Auto mode
1: Fixing mode 1
2: Fixing mode 2
3: Fixing mode 3
4: Fixing mode 1 in 15 deg C or more and fixing mode 3 in less than
15 deg C.
Default value 0
Related service mode COPIER> OPTION> IMG-FIX> FIX-ENV2 to 5, FX-LVL01 to 10
8-250
8-250