Canon imagePRESS 1135 Series Service Manual page 1230

COPIER > OPTION > USER
PR-PSESW Dspl/hide of output pause button
Lv.1 Details Setting to display/hide [Stop printing] button on the system-status/
stop screen.
Use case • Upon request from the user
• To promptly stop the print job in operation or under reservation
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF and then ON the main power supply.
Display/adj/set range 0 to 1
0: Hide (no display), 1: Display
Default value 1
IDPRN-SW Charge target jog set of dept mngt cuntr
Lv.1 Details Setting the type of job that advances the counter of department ID
control
Use case Upon request from the user
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF and then ON the main power supply.
Display/adj/set range 0 to 1
0:
PRINT category: BoxPrint, ReportPrint, SendLocalPrint, PDLPrint
COPY category: COPY
1:
PRINT category: ReportPrint, SendLocalPrint, PDLPrint
COPY category: COPY, BoxPrint
Default value 0
PCL-COPY Set of PCL COPIES command control method
Lv.2 Details Setting the binder control method of COPIES command with PCL.
Select whether to use the control method of Canon-made PCL or
use the same control method of non-Canon-made PCL.
Use case Upon request from the user
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF and then ON the main power supply.
Display/adj/set range 0 to 65535
0: Control method of Canon-made PCL (following the value of
COPIES command that is specified for each page to control on a
page-basis)
1: Control method of non-Canon-made PCL (handling the value of
COPIES command, which is specified for page 1at the time of
sorting, as bind figure while the value of COPIES command for the
next page or later is invalid. Same control applies as Canon-made
PCL at the time of non-sort mode)
2 to 65535: for future use
Default value 0
8
Service Mode > COPIER > OPTION (Mechanical specifications Setting Mode) > USER
8 Service Mode > COPIER > OPTION (Mechanical specifications Setting Mode) > USER
COPIER > OPTION > USER
CNT-SW Set default dspl items on charge counter
Lv.1 Details Setting of default display items of the charge counter on the screen
to check the counter status.
Use case Upon request from the user
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF and then ON the main power supply.
Caution Do not use this mode overseas (outside Japan).
Display/adj/set range 0 to 2
For Japan
0: counter 1 - total 1: 101
1: counter 1 - total 2: 102, counter 2 - copy - (total 2): 202,
counter 3 - total A2: 127
2: Not used
For UL
0: counter 1 - total 1: 101, counter 2 - total (large): 103, counter
3 - copy (total 1): 201, counter 4 - copy (large): 203
1: counter 1 - total 2: 102, counter 2 - copy (total 2): 202
2: Not used
Default value 0
TAB-ACC Auto cassette change set for index paper
Lv.1 Details Setting to enable/disable auto cassette change when index paper (tab
paper) is out.
Use case Upon request from the user
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF and then ON the main power supply.
Caution Be sure to instruct the user to thoroughly comply the following:
• Use index paper with the same number of tabs
• Set index paper
Be sure to comply the above, otherwise proper print is not available
and it can cause soil inside the machine because of toner.
Display/adj/set range 0 to 1
0: Disable auto cassette change, 1: Enable auto cassette change
Default value 1
REMPNL ON/OFF of remote panel function
Lv.1 Details ON/OFF setting of remote panel function
Selecting ON enables to operate the device from PC (just like
operating from the control panel).
Use case Upon request from the user
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF and then ON the main power supply.
Caution Do not use this mode overseas (outside Japan).
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 0
8-287
8-287