Canon imagePRESS 1135 Series Service Manual page 1186

COPIER > OPTION > IMG-FIX
FX-LP-2 Arch ctrl of fixing roller: 145kg pressr
Lv.1 Details Set ON/OFF of loop control for the fixing roller when 145 kg pressure
is applied (1900 pulse).
This item is used for Plain Paper 2 (80 to 105 g/m2), Thick Paper 1
(106 to 180 g/m2), Coated Paper 2 (91 to 120 g/m2), Coated Paper
3 (121 to 128 g/m2), and Coated Paper 4 (129 to 150 g/m2).
When loop control is set to OFF, an image failure "a line in main
scanning direction" due to the fixing feed speed can be prevented.
Use case When a line in main scanning direction is not eliminated even when
the speed of the fixing roller is adjusted
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF and then ON the main power supply.
Caution - Output a halftone image to check that there is no line in main
scanning direction.
- There should be no jam, buckling, or corner bend with the output
paper.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 1
Related service mode COPIER> OPTION> IMG-FIX> FX-SPD-2
COPIER> OPTION> FEED-SW> EX-MTR-2
Supplement/memo A line in main scanning direction: Because the feeding speed of the
fixing roller is faster than the secondary transfer external roller, the
paper is pulled between secondary transfer and fixing operation,
causing a line in main scanning direction at 227 to 255 mm from the
leading edge of the paper.
8
Service Mode > COPIER > OPTION (Mechanical specifications Setting Mode) > IMG-FIX
8 Service Mode > COPIER > OPTION (Mechanical specifications Setting Mode) > IMG-FIX
COPIER > OPTION > IMG-FIX
FX-LP-3 Arch ctrl of fixing roller: 175kg pressr
Lv.1 Details Set ON/OFF of loop control for the fixing roller when 175 kg pressure
is applied (2200 pulse).
This item is used for Thick Paper 2 (181 to 300 g/m2), Coated
Paper 5 (151 to 180 g/m2), Coated Paper 6 (181 to 240 g/m2), and
Embossed Paper.
When loop control is set to OFF, an image failure "a line in main
scanning direction" due to the fixing feed speed can be prevented.
Use case When a line in main scanning direction is not eliminated even when
the speed of the fixing roller is adjusted
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF and then ON the main power supply.
Caution - Output a halftone image to check that there is no line in main
scanning direction.
- There should be no jam, buckling, or corner bend with the output
paper.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 1
Related service mode COPIER> OPTION> IMG-FIX> FX-SPD-3
COPIER> OPTION> FEED-SW> EX-MTR-3
Supplement/memo A line in main scanning direction: Because the feeding speed of the
fixing roller is faster than the secondary transfer external roller, the
paper is pulled between secondary transfer and fixing operation,
causing a line in main scanning direction at 227 to 255 mm from the
leading edge of the paper.
RAG-SW ON/OFF of fixing burst control mode
Lv.1 Details ON/OFF setting for the mode to restrict fixing burst (skipping) as a
countermeasure for line burst.
Select 1: ON if there is side line burst on all the media.
Select ON according to the paper type if the line burst incident varies
according to the media.
Use case In the case of side line burst.
Adj/set/operate method Enter the setting value, and then press OK key.
Caution To activate skipping, specify 1 to 3 for RAG-CONT.
Display/adj/set range 0 to 3
0: OFF, 1: ON, 2: ON for coated paper group only,
3: OFF for coated paper group only
Default value 0
Related service mode COPIER> OPTION> IMG-FIX> RAG-CONT
8-243
8-243