Canon imagePRESS 1135 Series Service Manual page 794

Detail
Code Location Item
Code
E580 8017 51 Title Error in lock of stack tray up/down motor 1 (M20) of the
stacker
Description In the case that the arm is at the mechanical lower-limit
of detection position (without dolly, with delivery position tray, with the lifter
upper tray, the delivery position is at lower limit), although
turning ON of stack tray 1 full level sensor (S18) triggers to
stop rising of the stack tray, it failed to be ON even though 30
sec has passed.
Measures 1. Replace the stack tray 1 full level sensor (S18).
2. Replace the stack tray up/down motor 1 (M20).
3. Replace the slave controller PCB.
E580 8017 52 Title Error in lock of stack tray up/down motor 1 (M20) of the 2nd
stacker
Description In the case that the arm is at the mechanical lower-limit
of detection position (without dolly, with delivery position tray, with the lifter
upper tray, the delivery position is at lower limit), although
turning ON of stack tray 1 full level sensor (S18) triggers to
stop rising of the stack tray, it failed to be ON even though 30
sec has passed.
Measures 1. Replace the stack tray 1 full level sensor (S18).
2. Replace the stack tray up/down motor 1 (M20).
3. Replace the slave controller PCB.
E580 8018 51 Title Error in stack tray up/down motor of the stacker
Description With any operation other than removal-opening operation,
of detection the front cover was detected open during the job or removal
lowering/rising.
Measures 1. Replace the front cover open/close sensor (S52).
2. Replace the stack tray up/down motor 1 (M20) or stack tray
up/down motor 2 (M19).
3. Replace the slave controller PCB.
4. Replace the master controller PCB.
E580 8018 52 Title Error in stack tray up/down motor of the 2nd stacker
Description With any operation other than removal-opening operation,
of detection the front cover was detected open during the job or removal
lowering/rising.
Measures 1. Replace the front cover open/close sensor (S52).
2. Replace the stack tray up/down motor 1 (M20) or stack tray
up/down motor 2 (M19).
3. Replace the slave controller PCB.
4. Replace the master controller PCB.
7
Error Code > Error Code > Error Code Details
Description
7 Error Code > Error Code > Error Code Details
Detail
Code Location Item
Code
E580 8021 51 Title Error in lock of stack tray up/down motor 2 (M19) of the
stacker
Description In the case that stack tray 2 full level sensor (S23) and arm
of detection escape sensor 2 (S24) are ON, although turning ON of stack
tray 2 full level sensor (S23) triggers to stop lowering of the
stack tray, it failed to be OFF even though 30 sec has passed.
Measures 1. Check the connector of arm escape sensor 2 (S24), and
replace the sensor if necessary.
2. Replace the stack tray up/down motor 2 (M19).
3. Replace the slave controller PCB.
E580 8021 52 Title Error in lock of stack tray up/down motor 2 (M19) of the 2nd
stacker
Description In the case that stack tray 2 full level sensor (S23) and arm
of detection escape sensor 2 (S24) are ON, although turning ON of stack
tray 2 full level sensor (S23) triggers to stop lowering of the
stack tray, it failed to be OFF even though 30 sec has passed.
Measures 1. Check the connector of arm escape sensor 2 (S24), and
replace the sensor if necessary.
2. Replace the stack tray up/down motor 2 (M19).
3. Replace the slave controller PCB.
E580 8022 51 Title Error in lock of stack tray up/down motor 2 (M19) of the
stacker
Description In the case that stack tray 2 full level sensor (S23) is ON
of detection while arm escape sensor 2 (S24) is OFF, although turning ON
of arm escape sensor 2 (S24) triggers to stop lowering of the
stack tray it failed to be ON even though 30 sec has passed.
Measures 1. Check the connector of the arm escape sensor 2 (S24),
and replace the sensor if necessary.
2. Replace the stack tray up/down motor 1 (M20).
3. Replace the slave controller PCB.
E580 8022 52 Title Error in lock of stack tray up/down motor 2 (M19) of the 2nd
stacker
Description In the case that stack tray 2 full level sensor (S23) is ON
of detection while arm escape sensor 2 (S24) is OFF, although turning ON
of arm escape sensor 2 (S24) triggers to stop lowering of the
stack tray it failed to be ON even though 30 sec has passed.
Measures 1. Check the connector of the arm escape sensor 2 (S24),
and replace the sensor if necessary.
2. Replace the stack tray up/down motor 1 (M20).
3. Replace the slave controller PCB.
7-62
Description
7-62