Canon imagePRESS 1135 Series Service Manual page 994

Address bit Name
P039 15 Developing cooling fan full speed
14 Developing cooling fan half speed
13 Pre-primary transfer suction fan full speed
12 Pre-primary transfer suction fan half speed
11 Pre-exposure LED 1 ON
10 Pre-exposure LED 2 ON
9 Primary suction fan full speed
8 Primary suction fan half speed
7 M4 : Primary charging assembly cleaning
motor CW
M5 : Pre-primary transfer charging
assembly cleaning motor
6 M4 : Primary charging assembly cleaning
motor CCW
M5 : Pre-primary transfer charging
assembly cleaning motor
5 Not use
4 Not use
3 Not use
2 Not use
1 Not use
0 Not use
P040 15 Developing magnet roller motor ON
14 Not use
13 Drum potential sensor
12 Developing sleeve motor ON
11 Developing sleeve motor CW
10 Developing sleeve motor gain
9 Drum Cleaner motor ENABLE
8 Drum Cleaner motor ON
7 Drum Cleaner motor CW
6 Developing stirring motor ENABLE
5 Developing stirring motor CW
4 Developing stirring motor ON
3 Jam detection port
2 Error detection port
1 5V remote
0 Check operation LED
8
Service Mode > COPIER > I / O > Main Body (DCON > P001-052, P065 to 072)
Symbol Remarks
FM1 1: ON
FM1 1: ON
FM2 1: ON
FM2 1: ON
LED1 1: ON
LED2 1: ON
FM3 1: ON
FM3 1: ON
M4, M5 1: CW
M4, M5 1: CCW
- -
- -
- -
- -
- -
- -
M74 1: ON
- -
DP1 0: ON
M1 1: CW
M1 1: CW
M1
M7 1: Enable
M7 1: ON
M7 0: CW, 1: CCW
M2 1: Enable
M2 -
M2 -
- 1: Jam
- 1: Error
- 1: ON
1: ON
8 Service Mode > COPIER > I / O > Main Body (DCON > P001-052, P065 to 072)
Address bit Name
P041 15 Fixing heater control PCB connect detection -
14 Air pickup driver PCB connect detection
13 Developing driver PCB contact detection
(drawer)
12 Reverse delivery driver PCB connect
detection (drawer2)
11 Reverse delivery driver PCB connect
detection (drawer1)
10 ITB driver PCB contact detection (drawer)
9 Registration/duplexing driver PCB contact
detection (drawer2)
8 Registration/duplexing driver PCB contact
detection (drawer1)
7 Double feed detection PCB contact
detection
6 Fixing feed unit switch
5 Developing driver PCB 3.3 V Reset
detection
4 Fixing main driver PCB 3.3 V Reset
detection
3 Reverse delivery driver PCB 3.3V Reset
detection
2 ITB driver PCB 3.3 V Reset detection
1 Registration/duplexing driver PCB 3.3 V
Reset detection
0 Pickup feed driver PCB 3.3 V Reset
detection
8-51
Symbol Remarks
0: Not connected,
1: Connected
- 0: Not connected,
1: Connected
- 0: Connected,
1: Not connected
- 0: Connected,
1: Not connected
- 0: Connected,
1: Not connected
- 0: Connected,
1: Not connected
- 0: Connected,
1: Not connected
- 0: Connected,
1: Not connected
- 0: Not connected,
1: Connected
SW14 0: Closed when
the registration/
duplex driver PCB
is connected, or not
connected,
1: Open when the
registration/duplex
driver PCB is connected
- 1: Reset
- 1: Reset
- 1: Reset
- 1: Reset
- 1: Reset
- 1: Reset
8-51