Canon imagePRESS 1135 Series Service Manual page 780

Detail
Code Location Item
Code
E540 8001 51 Title Error in lock of upper tray up/down motor (M36) of the stacker
Description • In the case of initial lowering to move the tray down by
of detection 5mm from the OFF-state of the upper tray paper surface
sensor (S57), and then stop, lowering operation is not
complete even though specified period of time has passed
since the motor was driven.
• In the case of initial lowering to start moving down the tray
from the ON-state of the upper tray paper surface sensor
(S57) and move the tray down by 5mm after the upper
tray paper surface sensor (S57) was OFF, and then stop,
lowering operation is not complete even though specified
period of time has passed since the motor was driven.
• In the case of detecting paper surface position during
paper feeding to move the tray down by 30mm to stop,
lowering operation is not complete even though specified
period of time has passed since the motor was driven.
Measures 1. Check the connector of the upper tray paper surface
sensor (S57), and replace the sensor if necessary.
2. Replace the upper tray up/down motor (M36).
3. Replace the master controller PCB.
E540 8001 52 Title Error in lock of upper tray up/down motor (M36) of the 2nd
stacker
Description • In the case of initial lowering to move the tray down by
of detection 5mm from the OFF-state of the upper tray paper surface
sensor (S57), and then stop, lowering operation is not
complete even though specified period of time has passed
since the motor was driven.
• In the case of initial lowering to start moving down the tray
from the ON-state of the upper tray paper surface sensor
(S57) and move the tray down by 5mm after the upper
tray paper surface sensor (S57) was OFF, and then stop,
lowering operation is not complete even though specified
period of time has passed since the motor was driven.
• In the case of detecting paper surface position during
paper feeding to move the tray down by 30mm to stop,
lowering operation is not complete even though specified
period of time has passed since the motor was driven.
Measures 1. Check the connector of the upper tray paper surface
sensor (S57), and replace the sensor if necessary.
2. Replace the upper tray up/down motor (M36).
3. Replace the master controller PCB.
7
Error Code > Error Code > Error Code Details
Description
7 Error Code > Error Code > Error Code Details
Detail
Code Location Item
Code
E540 8002 02 Title a. Error in tray A (upper tray) (Fin-AK)
b. Error in the tray 1 shift motor (Fin-AG)
Description a. Detected position of tray A is below the tray B.
of detection b. The tray 1 detects the discontinuous area with the tray 1
area sensors.
Measures a-1. Check the connector of the tray A area sensor, and
replace the sensor if necessary.
a-2. Replace the finisher controller PCB.
b-1. Check the connectors of the tray 1 area sensors (S122/
S123/S124), and replace the sensors if necessary.
b-2. Check the connector of the tray 1 shift motor (M105), and
replace the motor if necessary.
b-3. Replace the finisher controller PCB.
E540 8002 51 Title Error in lock of upper tray up/down motor (M36) of the stacker
Description • In the case of initial rising to move the tray up after the
of detection upper tray paper surface sensor (S57) was ON to drive by
5mm, and then stop, rising operation is not complete even
though specified period of time has passed since the motor
was driven.
• In the case of detecting paper surface position during
paper feeding to move the tray up to drive by 5mm after
the upper tray paper surface sensor (S57) was ON, and
then stop, rising operation is not complete normally even
though specified period of time has passed since the motor
was driven.
Measures 1. Check the connector of the upper tray paper surface
sensor (S57), and replace the sensor if necessary.
2. Replace the upper tray up/down motor (M36).
3. Replace the master controller PCB.
E540 8002 52 Title Error in lock of upper tray up/down motor (M36) of the 2nd
stacker
Description • In the case of initial rising to move the tray up after the
of detection upper tray paper surface sensor (S57) was ON to drive by
5mm, and then stop, rising operation is not complete even
though specified period of time has passed since the motor
was driven.
• In the case of detecting paper surface position during
paper feeding to move the tray up to drive by 5mm after
the upper tray paper surface sensor (S57) was ON, and
then stop, rising operation is not complete normally even
though specified period of time has passed since the motor
was driven.
Measures 1. Check the connector of the upper tray paper surface
sensor (S57), and replace the sensor if necessary.
2. Replace the upper tray up/down motor (M36).
3. Replace the master controller PCB.
7-48
Description
7-48