Canon imagePRESS 1135 Series Service Manual page 1209

COPIER > OPTION > FEED-SW
CIS-SW Switching of CIS detection mode
Lv.2 Details Switch the CIS detection mode.
When an error occurred in the CIS pre-sample mode, select "CIS
threshold fixed mode".
Use case When an error occurs when CIS pre-sampling is performed with
colored paper/pre-print paper, etc.
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF and then ON the main power supply.
Display/adj/set range 0 to 1
0: CIS pre-sample mode
1: CIS threshold fixed mode
Default value 0
CIS-TH Adj CIS paper edge detect threshold VL
Lv.2 Details Adjusting the threshold for paper edge detection from side
registration detection with CIS paper.
With side registration detection, CIS guide (black) on the feeding
path is measured by CIS to determine paper edge when the
photosensitivity level of CIS exceeds the edge detection threshold.
If the edge cannot be detected (e.g. dark color paper), reduce this
threshold so that side registration can be properly executed.
Use case When an error occurs when CIS pre-sampling is performed with
colored paper/pre-print paper, etc.
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF and then ON the main power supply.
Display/adj/set range 0 to 255
Unit 7.8125 mV
Default value 26
8
Service Mode > COPIER > OPTION (Mechanical specifications Setting Mode) > FEED-SW
8 Service Mode > COPIER > OPTION (Mechanical specifications Setting Mode) > FEED-SW
COPIER > OPTION > FEED-SW
EX-MTR-1 Set delvrySPD ctrl in reverse/duplex mix
Lv.1 Details When the reverse delivery and the duplex delivery are mixed, the
productivity is reduced since the delivery&receipt speed from the
host machine to the downstream equipment is switched each time.
When this item is set to "1" or "2", the next delivery speed is
specified by the delivery speed control and the switching operation of
delivery&receipt speed will be decreased.
- Duplex delivery after reverse delivery: Increase the speed once
the trailing edge of a paper passes through the fixing until its leading
edge reaches to the downstream equipment.
- Reverse delivery after duplex delivery: Decrease the speed once a
paper is reversed after speed increase until its leading edge reaches
to the downstream equipment.
1: When "Delivery speed control is reset between jobs" is specified,
the delivery speed setting is reset per job and a previous job setting
does not affect to a next job.
2: When "Delivery speed control is not reset between jobs" is
specified, a next job is started while the delivery speed setting of a
previous job is maintained.
Use case When the productivity is low in 1-sided/duplex mixed
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range -5 to 5
-5 to -1, 3 to 5: Not used
0: Normal control
1: Delivery speed control is reset between jobs
2: Delivery speed control is not reset between jobs
Default value 1
EX-MTR-2 [Not used]
EX-MTR-3 [Not used]
PFIX-P-1 Pstn set prefixing feed assy: 52-63 g/m2
Lv.1 Details Lowering standby position of the pre-fixing feeding assembly to
secure feeding stability.
This mode only applies to LTR size or smaller paper with grammage
of 52 to 63 g/m2.
Use case - In the case of pre-fixing corner bend between secondary transfer
and the fixing
- In the case of big pre-fixing upper curl on the 1st side that prevents
the paper's leading edge from entering into the fixing roller nip,
resulting in inner delivery sensor delay jam
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF and then ON the main power supply.
Caution There should be no pre-fixing corner bend or inner delivery sensor
delay jam.
Display/adj/set range 0 to 1
0: Upper position, 1: Lower position
Default value 0
8-266
8-266