Juniper JUNOSE SOFTWARE FOR E SERIES 11.3.X - SYSTEM BASICS CONFIGURATION GUIDE 2010-10-04 Configuration Manual page 104
Software for e series broadband services routers system basics configuration guide
Hide thumbs
Also See for JUNOSE SOFTWARE FOR E SERIES 11.3.X - SYSTEM BASICS CONFIGURATION GUIDE 2010-10-04:
- Configuration manual (304 pages) ,
- Reference manual (284 pages)
Table of Contents
Advertisement
JunosE 11.3.x System Basics Configuration Guide
Table 10: Command Mode Overview (continued)
Mode Name
Use of Mode
Profile Configuration
QoS Interface Set
Configuration
QoS Interface Superet
Configuration
QoS Parameter
Definition Configuration
QoS Profile
Configuration
QoS Shared Shaper
Control Configuration
Queue Profile
Configuration
74
Access to Mode
Configure profiles.
Configure QoS interface
sets.
Configure QoS interface
supersets.
Configure QoS parameter
definitions.
Configure QoS profiles.
Configure variables within
the simple shared shaper
algorithm.
Configure queue profiles.
Exit from Mode
From Global Configuration
mode, use the profile
command.
Prompt:
host1(config-profile)#
From Global Configuration
mode, use the
qos-interface-set
command.
Prompt:
host1(config-qos-
interface-set)#
From Global Configuration
mode, use the
qos-interface-superset
command.
Prompt:
host1(config-qos-
interface-superet)#
From Global Configuration
mode, use the
qos-parameter-define
command.
Prompt:
host1(config-qos-
parameter-define)#
From Global Configuration
mode, use the qos-profile
command.
Prompt:
host1(config-qos-profile)#
From Global Configuration
mode, use the
qos-shared-shaper-control
command.
Prompt:
host1(config-qos-shar
ed-shaper-control)#
From Global Configuration
mode, use the
queue-profile command.
Prompt:
host1(config-queue)#
Copyright © 2010, Juniper Networks, Inc.
Use the exit command once to
return to Global Configuration
mode.
Press Ctrl+z to return to Exec
mode.
Use the exit command once to
return to Global Configuration
mode.
Press Ctrl+z to return to Exec
mode.
Use the exit command once to
return to Global Configuration
mode.
Press Ctrl+z to return to Exec
mode.
Use the exit command once to
return to Global Configuration
mode.
Press Ctrl+z to return to Exec
mode.
Use the exit command once to
return to Global Configuration
mode.
Press Ctrl+z to return to Exec
mode.
Use the exit command once to
return to Global Configuration
mode.
Press Ctrl+z to return to Exec
mode.
Use the exit command once to
return to Global Configuration
mode.
Press Ctrl+z to return to Exec
mode.
Advertisement
Table of Contents
Troubleshooting
Related Manuals for Juniper JUNOSE SOFTWARE FOR E SERIES 11.3.X - SYSTEM BASICS CONFIGURATION GUIDE 2010-10-04
Related Products for Juniper JUNOSE SOFTWARE FOR E SERIES 11.3.X - SYSTEM BASICS CONFIGURATION GUIDE 2010-10-04
- Juniper JUNOSE SOFTWARE FOR E SERIES 11.0.X - BGP AND MPLS CONFIGURATION GUIDE 2009-12-30
- Juniper JUNOSE SOFTWARE FOR E SERIES 11.3.X - BGP AND MPLS CONFIGURATION GUIDE 2010-10-12
- Juniper JUNOSE SOFTWARE FOR E SERIES 11.3.X - IP SERVICES CONFIGURATION GUIDE 2010-10-01
- Juniper JUNOSE SOFTWARE FOR E SERIES 11.3.X - MULTICAST ROUTING CONFIGURATION GUIDE 2010-10-07
- Juniper JUNOSE SOFTWARE FOR E SERIES 11.3.X - PHYSICAL LAYER CONFIGURATION GUIDE 2010-09-24
- Juniper JUNOSE SOFTWARE FOR E SERIES 11.3.X - SERVICE AVAILABILITY CONFIGURATION GUIDE 2010-10-08
- Juniper JUNOSE SOFTWARE FOR E SERIES 11.3.X - LINK LAYER CONFIGURATION GUIDE 2010-10-13
- Juniper JUNOSE SOFTWARE FOR E SERIES 11.3.X - QUALITY OF SERVICE CONFIGURATION GUIDE 2010-09-22
- Juniper JUNOS OS 10.3 - XML MANAGEMENT PROTOCOL GUIDE 6-30-2010
- Juniper JUNOS SOFTWARE 10.2 - SOFTWARE INSTALLATION AND UPGRADE GUIDE 4-28-2010
- Juniper JUNOS 10.1 - CONFIGURATION GUIDE 1-2010
- Juniper JUNOSE 11.1.X - BROADBAND ACCESS CONFIGURATION GUIDE 6-4-2010
- Juniper JUNOSE SOFTWARE 11.1.X - BROADBAND ACCESS CONFIGURATION GUIDE 6-6-2010
- Juniper JUNOSE SOFTWARE 11.0.X - LINK LAYER CONFIGURATION GUIDE 4-1-2010
- Juniper JUNOSE SOFTWARE 11.2.X - LINK LAYER CONFIGURATION GUIDE 7-7-2010
- Juniper JUNOSE SOFTWARE 11.2.X - BROADBAND ACCESS CONFIGURATION GUIDE 7-20-2010
Need help?
Do you have a question about the JUNOSE SOFTWARE FOR E SERIES 11.3.X - SYSTEM BASICS CONFIGURATION GUIDE 2010-10-04 and is the answer not in the manual?