Agilent Technologies InfiniiVision 7000A Series Programmer's Manual page 918

Index
SRE (Service Request Enable Register), 133,
759
SRQ (Service Request interrupt), 152, 159,
STANdard commands, 676
standard deviation measured on
waveform, 335
Standard Event Status Enable Register
(ESE), 118, 764
Standard Event Status Register (ESR), 120,
standard for video, 595
standard, LIN, 563
start acquisition, 136, 150, 174,
start and stop edges, 317
STARt commands, 676
start cursor, 719
start measurement, 312
start print job, 291
start time, 524, 719
start time marker, 716
state memory, 131
state of instrument, 123, 452
STATistics commands, 677
statistics increment, 340
statistics reset, 341
statistics results, 331
statistics, type of, 339
status, 134, 177, 179
Status Byte Register (STB), 132, 134, 135,
STATus commands, 677
status data structure clear, 117
status registers, 56
status reporting, 751
STB (Status Byte Register), 132, 134, 135,
step size for frequency span, 279
stop, 150, 178
stop acquisition, 178
STOP commands, 677
stop cursor, 720
stop displaying channel, 148
stop displaying math function, 148
stop displaying pod, 148
stop on mask test failure, 381
stop time, 524, 720
storage, 131
store instrument setup, 123, 131
store setup, 131
store waveforms to pixel memory,
storing calibration information, 210
string variables, 54
string variables, reading multiple query results
into, 55
string variables, reading query results into
multiple, 55
string, quoted ASCII, 109
subnet mask, 37
subsource, waveform source, 642
subsystem commands, 112, 806
subtract math function, 266, 273,
subtract math function as g(t) source,
sweep mode, trigger, 467, 477
sweep speed set to fast to measure fall
time, 322
918
sweep speed set to fast to measure rise
time, 334
163 switch disable,
switch, calibration protect,
sync break, LIN,
sync frame count (FlexRay),
syntax elements,
syntax rules, program data,
763 syntax, optional terms,
syntax, program message,
SYSTem commands,
176 system commands, 446, 447, 448, 449, 452,
454
system commands introduction,
T
tdelta, 715
tedge, 342
telnet ports 5024 and 5025,
Telnet sockets,
temporary message,
TER (Trigger Event Register), 179,
termination conditions, mask test,
test sigma, mask test run,
test, self, 137
text, writing to display,
757
threshold, 243, 395, 695,
THReshold commands,
threshold voltage (lower) for
measurement,
threshold voltage (upper) for
757
measurement,
thresholds, 317,
thresholds used to measure period,
thresholds, how autoscale affects,
TIFF image format,
time base, 457, 458, 459, 461, 462,
time base commands introduction,
time base reset conditions,
time base window, 464, 465,
time between points,
time buckets, 184,
TIME commands,
time delay, 737
time delta, 715
158
time difference between data points,
time duration, 490, 491, 494,
time holdoff for trigger,
time interval, 342, 344,
time interval between trigger and
occurrence,
time marker sets start time,
time per division,
time record, 280
time specified,
time, calibration,
638
time, mask test run,
269
time, start marker,
time, stop marker,
time, system,
time/div, how autoscale affects,
Agilent InfiniiVision 7000A Series Oscilloscopes Programmer's Guide
449
214
564
430
108
790
108
787
445
445
626
57
447
760
377
382
447
741
678
713
723
716
327
144
409
737
456
128
466
715
185
678
646
524
472
715
721
716
459
354
216
383
719
720
454
144
time-at-max measurement, 717
time-at-min measurement, 718
TIMebase commands, 455
timebase vernier, 463
TIMebase:MODE, 52
time-ordered label list, 250
timeout, 583
timer, 579
timing measurement, 312
title channels, 225
title, mask test, 391
tolerance, automask, 366, 367
top of waveform value measured,
TOTal commands, 678
total frame count (CAN), 425
total frame count (FlexRay), 431
total waveforms in mask test, 371
trace memories, how autoscale affects,
trace memory, 177, 180
trace memory data, 247
track measurements, 336
trademarks, 2
transfer instrument state, 123, 452
transmit, 247
transmit word size, I2S, 542
tree traversal rules, 806
tree, command, 791
TRG (Trigger), 133, 135, 136
TRIG OUT BNC, 211
trigger (external) input impedance, 257,
trigger armed event register, 165,
trigger burst, UART, 601
TRIGger CAN commands, 478
trigger channel source, 525, 594
TRIGger commands, 467, 678
TRIGger commands, general, 470
trigger data, UART, 602
trigger duration, 490, 491
TRIGger DURation commands, 489
TRIGger EBURst commands, 495
trigger edge, 575
TRIGger EDGE commands, 499
trigger edge coupling, 500
trigger edge slope, 503
trigger event bit, 179
Trigger Event Register (TER), 760
TRIGger FLEXray commands, 505
TRIGger GLITch commands, 517
trigger holdoff, 472
TRIGger I2S commands, 526
trigger idle, UART, 603
TRIGger IIC commands, 544
trigger level constants, 227
trigger level voltage, 501
TRIGger LIN commands, 553
TRIGger M1553 commands, 566
trigger occurred, 135
trigger pattern, 475, 492
trigger qualifier, 493
trigger qualifier, UART, 606
trigger reset conditions, 128
TRIGger SEQuence commands, 573
355
144
702
167