Agilent Technologies InfiniiVision 7000A Series Programmer's Manual page 917

Request-for-OPC flag clear, 117
reset, 128, 578
RESet commands, 672
reset conditions, 128
reset mask statistics, 369
reset measurements, 149, 246
resolution of printed copy, 710
resource session object, 49
ResourceManager object, 49
restore configurations, 123, 127, 131,
restore labels, 249
restore setup, 127
return values, query, 808
returning acquisition type, 196
returning number of data points,
right reference, 461
rise time measurement, 312
rise time of positive edge, 334
rising edge, 475, 575
RMODe commands, 672
RMS value measurement, 353
roll time base mode, 457
root (:) commands, 139, 141
root level commands, 112
RQL (Request Control) status bit, 119,
RQS (Request Service), 135
RS-232/UART triggering, 469
RST (Reset), 128
rules, tree traversal, 806
rules, truncation, 788
RUMode commands, 672
run, 136, 174
Run bit, 165, 167
run mode, mask test, 377
running configuration, 131, 452
Rx frame count (UART), 442
Rx source, 607
S
sample rate, 195
sampled data, 699
sampled data points, 626
SAMPlepoint commands, 673
SAV (Save), 131
save, 131, 404
SAVE commands, 403, 673
save filename, 405
save image, 406
save image with inksaver, 410
save mask, 412, 413
save mask test failures, 380
save path information, 414
save setup, 415
SAVE TO INTERN, 158
save waveform data, 416
save waveforms to pixel memory,
saved image, area, 407
saving and recalling data, 244
SBUS commands, 420
scale, 276, 462, 466
SCALe commands, 674
Agilent InfiniiVision 7000A Series Oscilloscopes Programmer's Guide
scale factors output on hardcopy, 285,
scale for channels,
scale units for channels,
scale units for external trigger,
scaling display factors,
SCPI commands,
scratch measurements,
screen area for hardcopy print,
screen area for saved image,
452 screen data, 247
SECAM, 591,
seconds per division,
SEGMented commands,
segmented waveform save option,
188 segments, analyze,
segments, count of waveform,
segments, setting number of memory,
segments, setting the index,
segments, time tag,
select measurement channel,
self-test, 137
sensing a channel probe,
sensing a external trigger probe,
sensitivity of oscilloscope input,
121 sequence, 576, 577,
sequence trigger,
SEQuence trigger commands,
sequence triggering,
sequencer edge counter,
sequencer timer,
sequential commands,
serial clock, 548,
serial data, 549,
serial decode bus,
serial decode bus display,
serial decode mode,
serial frame, 589
serial number,
service request,
Service Request Enable Register (SRE), 133,
759
set, 128
set center frequency,
set conditions,
set cursors, 719,
set date, 446
set delay, 144
set thresholds,
set time, 454
set time/div, 144
set up oscilloscope,
setting digital display,
setting digital label, 205,
setting digital position,
setting digital threshold,
setting display,
setting external trigger level,
158
setting impedance for channels,
setting inversion for channels,
setting pod display,
setting pod size,
setting pod threshold,
408
234
235
263
227
57
714
283
407
595
462
674
419
190
636
191
192
637
337
698
703
227
578
580
573
469
574
579
809
587
588
421
427
436
175
135
267
144
720
144
37
239
240
241
243
268
254
223
224
393
394
395
settings, 127, 131
settings, instrument, 282
setup, 182, 199, 219, 237, 244, 266, 282,
SETup commands, 674
setup configuration, 127, 131, 452
setup defaults, 128
setup memory, 127
setup reported, 469
setup, recall, 402
setup, save, 415
short form, 4, 788
show channel labels, 249
show measurements, 312, 336
SICL example in C, 891
SICL example in Visual Basic, 900
SICL examples, 891
sigma, mask test run, 382
SIGNal commands, 675
signal type, 231, 260
signed data, 622
simple command headers, 789
single acquisition, 176
single-ended probe heads, 228
single-ended signal type, 231, 260
single-shot DUT, synchronizing with,
size, 242, 394
SIZE commands, 675
skew, 230, 696
slope, 503, 582
slope (direction) of waveform, 721
SLOPe commands, 675
slope not valid in TV trigger mode,
slope of edge, 575
slope parameter for delay measurement,
slope, Nth edge in burst, 498
smoothing acquisition type, 620
software version, 122
source, 252, 266, 337, 486, 562,
SOURce commands, 675
source for function, 277, 278, 704
source for trigger, 504
source for TV trigger, 594
source, automask, 364
source, FLEXray, 515
source, mask test, 390
SOURce1 commands, 676
SOURce2 commands, 676
span, 266
span of frequency on display, 279
specify measurement, 337
SPI, 582, 583, 585
SPI commands, 676
SPI decode bit order, 437
SPI decode word width, 438
SPI trigger, 584, 586
SPI trigger clock, 587
SPI trigger commands, 581
SPI trigger data, 588
SPI trigger frame, 589
SPI triggering, 469
square root math function, 273
Index
452
780
503
319
638
917