Service Information - Honda CB 600F Hornet 2007 Shop Manual

FRONT WHEEL/SUSPENSION/STEERING

SERVICE INFORMATION

GENERAL
• When servicing the front wheel, fork or steering stem, support the motorcycle using a safety stand or hoist.
• A contaminated brake disc or pad reduces stopping power. Discard contaminated pads and clean a contaminated disc
with a high quality brake degreasing agent.
• After the front wheel installation. check the brake operation by applying the brake lever.
• Refer to the brake system information (page 15-4).
• Use only tires marked "TUBELESS" and tubeless valves on rim marked "TUBELESS TIRE AP PLICABLE".
SPECIFICATIONS
ITEM
Minimum tire tread depth
Cold tire Driver only
pressure
Driver and passenger
Axle runout
Radial
Wheel rim
runout
Axial
Wheel balance weight
Fork Spring free length
Pipe runout
Recommended fork fluid
Fluid level
Fluid capacity
7teering head-bearing pre-load
TORQUE VALUES
Handlebar holder bolt
Steering stem adjusting lock nut
Steering stem adjusting nut
Steering stem nut
Bottom bridge pinch bolt
Top bridge pinch bolt
Fork bolt
Fork bolt lock nut
Fork socket bo It
Front axle pinch bolt
Front axle bolt
Front brake disc mounting bolt
Front brake master cylinder holder bolt
Front brake caliper mounting bolt
Front brake hose clamp bolt
Front pulser ring mounting bolt
(CB600FA)
13-4
250 kPa (2.50 kgf/cm', 36 psi)
250 kPa (2.50 kgf/cm', 36 psi)
245.7 (9.67)
Honda Ultra Cushion Oil 10W or equivalent
70 (2.8)
494 ± 2.5
Imp oz)
8.8 - 13. 7
27 N•m (2.8 kgf•m, 20 lbf . ft)
See page 13-37
26 N·m (2.7 kgf•m, 19 lbf . ft)
103 N·m (10.5 kgf-m, 76 lbf-ft)
39 N•m (4.0 kgf•m, 29 lbf•ft)
22 N·m (2.2 kgf•m, 16 lbf•ft)
34 N-m (3.5 kgf•m, 25 lbf·ft)
20 N•m (2.0 kgf•m, 15 !bf . ft)
20 N•m (2.0 kgf•m, 15 lbf•ft)
22 N·m (2.2 kgf·m, 16 lbf·ft)
59 N·m (6.0 kgf•m, 44 lbf·ft)
20 N•m (2.0 kgf-m, 15 lbf·ft)
12 N•m (1.2 kgf•m, 9 lbf•ft)
30 N·m (3.1 kgf·m. 22 lbf•ft)
CB600FA: 10 N•m (1.0 kgf-m, 7 lbf-ft)
CB600F: 12 N·m (1.2 kgf·m, 9 lbf·ft)
7.0 N-m (0.7 kgf,m, 5.2 lbf•ft)
STANDARD
-
-
-
-
-
-
cm' (16.7 ± 0.08 US oz, 17.4 ±
N (0.9 - 1.4 kgf, 2.0- 3.1 lbf)
Apply engine oil to the threads.
Apply a locking agent to the threads.
ALOC bolt; replace with a new one.
ALOC bolt; replace with a new one.
ALOC bolt; replace with a new one.
ALOC bolt; replace with a new one.
Unit· mm (in)
-
SERVICE LIMIT
1.5 (0.06)
-
-
0 . 2 (0.01)
2.0 (0.08)
2.0 (0.08)
60 g (2.1oz) max.
240.8 (9.48)
0.20 (0.008)
-
-
-
0.09
-