Service Information; Special Tools; Common Tools; Driver Handle A Tool - Honda CM 185T 1981 Manual

SERVICE INFORMATION

TROUBLESHOOTING
REAR WHEEL
REAR BRAKE PANEL
REAR SHOCK ABSORBER
SWING AR M
REAR BRAKE PEDAL
SERVICE INFORMATION
• W O R K I N G P R A C T I C E
This section describes removal, installation and repair of the rear shock absrobers, the swingarm and the rear brake.
This vehicle does not have a center stand. Support the engine w i t h a block or the frame body w i t h a rigid rack securely, when
removing the rear wheel.
• T O O L S

Special Tools

Rear shock absorber compressor Tool No. 0 7 9 5 9 - 3 2 9 0 0 0 1
Spring holder attachment Tool No. 0 7 9 6 7 - 1 1 5 0 1 0 0

Common Tools

Bearing driver (42x47)
Tool No. 0 7 7 4 6 - 0 0 1 0 3 0 0
Driver handle A
Tool No. 0 7 7 4 9 - 0 0 1 0 0 0 0
Pilot (15)

Tool No. 0 7 7 4 6 - 0 0 4 0 3 0 0

• T O R Q U E S
Axle nut: 4 . 0 - 5 . 0 kg-m ( 2 8 . 9 - 3 6 . 2 ft-lb.
Swingarm pivot bolt: 5 . 0 - 6 . 0 kg-m ( 3 6 . 2 - 4 3 . 4 ft-lb.
Rear brake torque link nut: 2 . 0 - 2 . 5 kg-m ( 1 4 . 5 - 1 8 . 1 ft-lb.
Shock absorber nut: 3 . 0 - 4 . 0 kg-m ( 2 1 . 7 - 2 8 . 9 ft-lb.
Driven sprocket nut; 5 . 5 - 6 . 5 kg-m ( 3 9 . 8 - 4 7 . 0 ft-lb.
Brake cam bolt: 0 . 8 - 1 . 2 kg-m ( 5 . 8 - 8 . 6 ft-lb.)
• S E R V I C E D A T A
ITEMS
Axle bend
Wheel rim runout Radial
Axial
Brake d r u m I.D.
Brake lining thickness
Rear shock absorber spring free length
Swingarm pivot bushing clearance
Date of Issue: December, 1977
© HONDA MOTOR CO., L T D .
12 REAR WHEEL/
REAR SUSPENSION
1 2 - 1
1 2 - 2
1 2 - 3
1 2 - 8
1 2 - 1 0
1 2 - 1 2
1 2 - 1 3
S T A N D A R D
-----------------------
-----------------------
-----------------------
130.0 mm (5.1181 in.)
4.0 mm (0.1575 in.)
184.1 mm (7.2480 in.)
0 . 2 - 0 . 3 mm ( 0 . 0 0 7 9 - 0 . 0 1 1 8 in.)
SERVICE L I M I T
0.2 mm (0.0079 in.)
2.0 mm (0.0787 in.)
2.0 mm (0.0787 in.)
131.0 mm (5.1575 in.)
2.0 mm (0.0787 in.)
175.6 mm (6.9133 in.)
0.5 mm (0.0197 in.)
12-1