H6: Pulse Train Input/Output - YASKAWA GA800 Technical Reference

No.
Name
(Hex.)
H5-10 Modbus Register 0025H
Unit Sel
(0436)
H5-11 Comm ENTER
Command Mode
(043C)
H5-12 Run Command Method
Selection
(043D)
H5-17 ENTER command
response @CPU BUSY
(11A1)
Expert
H5-18 Motor Speed Filter over
Comms
(11A2)
H5-20 Communication
Parameters Reload
(0B57)
H5-22 Speed Search from
MODBUS
(11CF)
H5-25 Function 5A Register 1
Selection
(1589)
RUN
H5-26 Function 5A Register 2
Selection
(158A)
RUN
H5-27 Function 5A Register 3
Selection
(158B)
RUN
H5-28 Function 5A Register 4
Selection
(158C)
RUN
◆

H6: Pulse Train Input/Output

No.
Name
(Hex.)
H6-01 Terminal RP Pulse Train
Function
(042C)
H6-02 Terminal RP Frequency
Scaling
(042D)
RUN
YASKAWA SIEPC71061737D GA800 Drive Technical Reference
Description
V/f CL-V/f OLV CLV AOLV
Sets the unit of measure used for the MEMOBUS/Modbus communications monitor
register 0025H (output voltage reference monitor).
0 : 0.1 V units
1 : 1 V units
V/f CL-V/f OLV CLV AOLV
Sets the function to make the Enter command necessary to change parameters through
MEMOBUS/Modbus communications.
0 : ENTER Command Required
1 : ENTER Command Not Required
V/f CL-V/f OLV CLV AOLV
Sets the input method for the Run command when b1-02 = 2 [Run Command Selection 1 =
Memobus/Modbus Communications] or b1-16 = 2 [Run Command Selection 2 =
Memobus/Modbus Communications].
0 : FWD/Stop, REV/Stop
1 : Run/Stop, FWD/REV
V/f CL-V/f OLV CLV AOLV
Sets operation when the EEPROM write command is sent without EEPROM write
available. Usually it is not necessary to change this setting.
0 : Ignore Command(No ROM/RAM Write)
1 : Write to RAM Only
V/f CL-V/f OLV CLV AOLV
Sets the filter time constant used when monitoring motor speed during MEMOBUS/
Modbus communications or with a communication option.
V/f CL-V/f OLV CLV AOLV
Sets the function to immediately enable updated MEMOBUS/Modbus communications
parameters.
0 : Reload at Next Power Cycle
1 : Reload Now
V/f CL-V/f OLV CLV AOLV
Enables the MEMOBUS/Modbus communication register Speed Search function (bit0 of
15DFH).
0 : Disabled
1 : Enabled
V/f CL-V/f OLV CLV AOLV
Returns the contents of the specified MEMOBUS/Modbus communications register when
responding to the master device.
V/f CL-V/f OLV CLV AOLV
Returns the contents of the specified MEMOBUS/Modbus communications register when
responding to the master device.
V/f CL-V/f OLV CLV AOLV
Returns the contents of the specified MEMOBUS/Modbus communications register when
responding to the master device.
V/f CL-V/f OLV CLV AOLV
Returns the contents of the specified MEMOBUS/Modbus communications register when
responding to the master device.
Description
V/f CL-V/f OLV CLV AOLV
Sets the function for pulse train input terminal RP.
0 : Frequency Reference
1 : PID Feedback Value
2 : PID Setpoint Value
3 : Speed Feedback (V/F Control)
V/f CL-V/f OLV CLV AOLV
Sets the frequency of the pulse train input signal used when the item selected with H6-01
[Terminal RP Pulse Train Function] is input at 100%.
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
11.10 H: Terminal Functions
Default
Ref.
(Range)
0 947
(0, 1)
0 948
(0, 1)
0 948
(0, 1)
0 948
(0, 1)
0 ms 948
(0 - 100 ms)
0 949
(0, 1)
0 949
(0, 1)
0044H (U1-05) 949
(0000H - FFFFH)
0045H (U1-06) 949
(0000H - FFFFH)
0042H (U1-03) 949
(0000H - FFFFH)
0049H (U1-10) 950
(0000H - FFFFH)
Default
Ref.
(Range)
0 950
(0 - 3)
1440 Hz 951
(100 - 32000 Hz)
11
611