YASKAWA GA800 Technical Reference page 550

11.5 b: Application
No.
Name
(Hex.)
b5-60 PID Setpoints 4
(1184)
RUN
b5-61 PID Trim Mode Lower
Limit Sel
(119A)
b5-62 PID Trim Mode Lower
Limit Value
(119B)
b5-63 PID Differential FB
Monitor Sel
(119C)
b5-64 PID Differential FB
Monitor Gain
(119D)
b5-65 PID Differential FB
Monitor Bias
(119F)
b5-66 PID Feedback Monitor
Level
(11DE)
b5-67 PID Differential FB
Monitor Lvl
(11DF)
b5-89 Sleep Method Selection
(0B89)
RUN
b5-90 EZ Sleep Unit
(0B90)
b5-91 EZ Sleep Minimum
Speed
(0B91)
RUN
b5-92 EZ Sleep Level
(0B92)
RUN
b5-93 EZ Sleep Time
(0B93)
RUN
b5-94 EZ Sleep Wake-up Level
(0B94)
RUN
550
V/f CL-V/f OLV CLV AOLV
Sets the PID setpoint when H1-xx = 3E or 3F [MFDI Function Select = PID Setpoint
Selection 1/2]. This value is a percentage of the maximum output frequency.
Note:
Parameter A1-02 [Control Method Selection] selects which parameter is the maximum
output frequency.
• A1-02 ≠ 8 [EZOLV]: E1-04 [Maximum Output Frequency]
• A1-02 = 8: E9-02 [Maximum Speed]
V/f CL-V/f OLV CLV AOLV
Sets the function that adjusts the PID output in relation to the frequency reference.
0 : Disabled
1 : Enabled
V/f CL-V/f OLV CLV AOLV
Sets the PID Trim Mode Lower Limit Value as a percentage of the maximum output
frequency.
Note:
Parameter A1-02 [Control Method Selection] selects which parameter is the maximum
output frequency.
• A1-02 ≠ 8 [EZOLV]: E1-04 [Maximum Output Frequency]
• A1-02 = 8: E9-02 [Maximum Speed]
V/f CL-V/f OLV CLV AOLV
Selects the monitor (Ux-xx) used as the PID Differential Feedback. Set the x-xx part of the
Ux-xx [Monitor].
V/f CL-V/f OLV CLV AOLV
Sets the gain for the monitor specified in b5-63 [PID Differential FB Monitor Sel].
V/f CL-V/f OLV CLV AOLV
Sets the bias for the monitor specified in b5-63 [PID Differential FB Monitor Sel].
V/f CL-V/f OLV CLV AOLV
Sets the signal level for the monitor specified in b5-55 [PID Feedback Monitor Selection].
0 : Absolute
1 : Bi-directional (+/-)
V/f CL-V/f OLV CLV AOLV
Sets the signal level for the monitor specified in b5-63 [PID Differential FB Monitor Sel].
0 : Absolute
1 : Bi-directional (+/-)
V/f CL-V/f OLV CLV AOLV
Sets sleep and wake up operation when using PID.
0 : Standard
1 : EZ Sleep/Wake-up
V/f CL-V/f OLV CLV AOLV
Sets the measurement units for b5-91 [EZ Sleep Minimum Speed] and b5-92 [EZ Sleep
Level].
0 : 0.1Hz units
1 : rev/min
V/f CL-V/f OLV CLV AOLV
Sets the minimum speed for the EZ Sleep/Wakeup function. This parameter uses the
largest value from b5-91, b5-34 [PID Output Lower Limit Level], and d2-02 [Frequency
Reference Lower Limit].
V/f CL-V/f OLV CLV AOLV
Sets the value that the output frequency or motor speed must be less than for longer than
b5-93 [EZ Sleep Time] to enter Sleep Mode.
V/f CL-V/f OLV CLV AOLV
Sets the length of time that the output frequency or motor speed must be less than b5-92
[EZ Sleep Level] to enter Sleep Mode.
V/f CL-V/f OLV CLV AOLV
Sets the level at which the drive resumes operation when exiting Sleep Mode.
Description
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
YASKAWA SIEPC71061737D GA800 Drive Technical Reference
Default
Ref.
(Range)
0.00% 757
(0.00 - 100.00%)
0 757
(0, 1)
0.00% 758
(0.00 - 100.00%)
000 758
(000 - 999)
1.00 758
(0.00 - 10.00)
0.00 758
(-10.00 - +10.00)
0 758
(0, 1)
0 759
(0, 1)
0 759
(0, 1)
0 759
(0, 1)
0.0 Hz or 0 min -1 (r/min) 759
(0.0 to 590.0 Hz or 0 to
35400 min -1 (r/min))
-1
0.0 Hz or 0 min (r/min) 759
(0.0 to 590.0 Hz or 0 to
-1
35400 min (r/min))
5.0 s 759
(0.0 - 1000.0 s)
0.00% 760
(0.00 - 600.00%)