YASKAWA GA800 Technical Reference page 252

5.2 European Standards
Model Terminal
R/L1, S/L2, T/L3
U/T1, V/T2, W/T3
4477 -, +1
+3
R/L1, S/L2, T/L3
U/T1, V/T2, W/T3
4568 -, +1
+3
R/L1, S/L2, T/L3
U/T1, V/T2, W/T3
4605 -, +1
+3
R/L1, S/L2, T/L3
U/T1, V/T2, W/T3
4720 -, +1
+3
*1 For IP20 protection, use wires that are in the range of applicable gauges.
*2 Remove insulation from the ends of wires to expose the length of wire shown.
*3 For wire gauges more than 30 mm
*4 Install a GFCI with this wire gauge to maintain compliance with IEC/EN 61800-5-1:2007.
*5 Terminals - and +1 have two screws. The Recommended Gauge is the wire gauge for one terminal.
*6 A junction terminal is necessary to connect a braking resistor unit (LKEB-series) to terminals B1 and B2.
252
Applicable Gauge
Recomm. Gauge
(IP20 Applicable Gauge
mm 2
70 - 150 × 4P
120 × 4P
70 - 150 × 4P
95 × 4P
(120 - 150 × 4P)
95 - 185 × 4P
95 × 4P
35 - 95 × 4P
70 × 4P
150
70 - 150 × 4P
120 × 4P
70 - 150 × 4P
95 × 4P
(120 - 150 × 4P)
95 - 185 × 4P
95 × 4P
35 - 95 × 4P
70 × 4P
95 × 2P
70 - 150 × 4P
120 × 4P
70 - 150 × 4P
95 × 4P
(120 - 150 × 4P)
95 - 185 × 4P
95 × 4P
35 - 95 × 4P
70 × 4P
95 × 2P
70 - 150 × 4P
120 × 4P
70 - 150 × 4P
95 × 4P
(120 - 150 × 4P)
95 - 185 × 4P
95 × 4P
35 - 95 × 4P
70 × 4P
95 × 2P
2 , tighten to a tightening torque of 4.1 N∙m to 4.5 N∙m (36 lbf∙in to 40 lbf∙in).
Wire Stripping
*2
Length
*1 )
mm
mm 2
-
(150 × 4P)
-
-
(185 × 4P)
-
(95 × 4P)
50 - 150
-
(-)
-
(150 × 4P)
-
-
(185 × 4P)
-
(95 × 4P)
60 - 150
-
(-)
-
(150 × 4P)
-
-
(185 × 4P)
-
(95 × 4P)
60 - 150
-
(-)
-
(150 × 4P)
-
-
(185 × 4P)
-
(95 × 4P)
60 - 150
-
(-)
YASKAWA SIEPC71061737D GA800 Drive Technical Reference
Terminal Screw Tightening Torque
Size and Shape N∙m (lbf∙in)
35
M12
(310)
35
M12
(310)
35
M12
(310)
35
M12
(310)
32 - 40
M12
(283 - 354)
35
M12
(310)
35
M12
(310)
35
M12
(310)
35
M12
(310)
32 - 40
M12
(283 - 354)
35
M12
(310)
35
M12
(310)
35
M12
(310)
35
M12
(310)
32 - 40
M12
(283 - 354)
35
M12
(310)
35
M12
(310)
35
M12
(310)
35
M12
(310)
32 - 40
M12
(283 - 354)