H3: Analog Inputs - YASKAWA GA800 Technical Reference

■
6A: Data Logger Error
Setting Value Function
6A Data Logger Error
■
90 to 93: DWEZ Digital Outputs 1 to 4
Setting Value Function
90 to 93 DWEZ Digital Outputs 1 to
4
■
A0 to A7: DWEZ Extended Digital Outputs 1 to 8
Setting Value Function
A0 to A7 DWEZ Extended Digital
Outputs 1 to 8
■
100 to 1A7: Inverse Outputs of 0 to A7
Setting Value Function
100 to 1A7 Inverse Outputs of 0 to A7
For example, set H2-xx = 10E for the inverse output of E [Fault].
◆

H3: Analog Inputs

WARNING! Sudden Movement Hazard. Do test runs and examine the drive to make sure that the command references are correct.
If you set the command reference incorrectly, it can cause damage to the drive or serious injury or death.
Drives have three analog input terminals, terminals A1, A2, and A3. H3 parameters select the functions set to these
analog input terminals and adjust signal levels.
Table 12.64 shows the functions that you can set to analog input terminals. Use H3-02, H3-06, and H3-10 [MFAI
Function Selection] to set functions.
Setting
Function
Value
0 Frequency Reference
1 Frequency Gain
2 Auxiliary Frequency Reference 1
3 Auxiliary Frequency Reference 2
4 Output Voltage Bias
5 Accel/Decel Time Gain
6 DC Injection Braking Current
7 Torque Detection Level
8 Stall Prevent Level During Run
9 Output Frequency Lower Limit
B PID Feedback
C PID Setpoint
D Frequency Bias
Note:
All analog input scaling uses gain and bias for adjustment. Set the gain and bias values correctly.
YASKAWA SIEPC71061737D GA800 Drive Technical Reference
V/f CL-V/f OLV CLV AOLV
The terminal activates when the drive detects a LoG [Com Error / Abnormal SD card].
V/f CL-V/f OLV CLV AOLV
Sets the DriveWorksEZ digital output. Refer to the DriveWorksEZ online manual for more information.
V/f CL-V/f OLV CLV AOLV
Sets the digital output for the DriveWorksEZ DO-A3 option card. Refer to the DriveWorksEZ online manual for more information.
V/f CL-V/f OLV CLV AOLV
Causes inverse output of the function for the selected MFDO. Uses the last two digits of 1xx to select which function to inversely
output.
Table 12.64 MFAI Setting Values
Ref.
936
936
936
937
937
937
937
938
938
938
938
939
939
Description
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
Description
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
Description
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
Description
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
Setting
Function
Value
E Motor Temperature (PTC Input)
F Not Used
10 Forward Torque Limit
11 Reverse Torque Limit
12 Regenerative Torque Limit
13 Torque Reference / Torque Limit
14 Torque Compensation
15 General Torque Limit
16 Differential PID Feedback
1F Not Used
30 DWEZ Analog Input 1
31 DWEZ Analog Input 2
32 DWEZ Analog Input 3
12.8 H: Terminal Functions
Ref.
939
939
939
940
941
941
941
941
941
941
941
942
942
12
929