Renault Laguna III Manual page 370

ENGINE AND CYLINDER BLOCK ASSEMBLY
Drive plate: Removal - Refitting
V4Y
Special tooling required
Mot. 1390 Support for removal - refitting
of engine - gearbox assembly
Mot. 919-02 Flywheel locking tool.
Equipment required
refrigerant charging station
component support
Tightening torquesm
drive plate bolts
central nut of the left-
hand suspended engine
mounting rubber pad
IMPORTANT
Wear protective gloves during the operation.
WARNING
It is strictly forbidden to apply any pressure to the
engine oil sump. Damage to the sump will irrepara-
bly damage the engine by:
- blocking the strainer,
- raising the oil level above maximum, with a risk of
engine racing.
REMOVAL
I - REMOVAL PREPARATION OPERATION
a Position the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
a Disconnect the battery (see Battery: Removal - Re-
fitting) (80A, Battery).
a Remove:
- the front wheels (see Wheel: Removal - Refitting)
(35A, Wheels and tyres),
- the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion),
- the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection),
- the headlights (see Headlight: Removal - Refit-
ting) (80B, Headlights),
- the bonnet catch (see Bonnet lock: Removal -
Refitting) (52A, Non-side opening element mecha-
nisms),
- the audible warning (see Audible warning: Re-
moval - Refitting) (82B, Horn),
- the front end panel (see Front end panel: Remov-
al - Refitting) (42A, Upper front structure),
- the petrol injection computer (see 17B, Petrol in-
jection, Petrol injection computer: Removal -
Refitting, page 17B-30) ,
- the air filter unit (see 12A, Fuel mixture, Air filter
unit: Removal - Refitting, page 12A-13) .
88 N.m
a Drain:
62 N.m
- the refrigerant circuit using a refrigerant charging
station (see Refrigerant circuit: Draining - Fill-
ing) (62A, Air conditioning),
- the cooling system (see 19A, Cooling, Cooling
system: Draining - Refilling, page 19A-16) .
a Remove:
- the "radiator - condenser - fan assembly" assembly
(see 19A, Cooling, Cooling radiator: Removal -
Refitting, page 19A-28) ,
- the front right-hand driveshaft (see Front right-
hand driveshaft: Removal - Refitting) (29A,
Driveshafts),
- the front left-hand driveshaft (see Front left-hand
driveshaft: Removal - Refitting) (29A, Drive-
shafts),
- the battery disconnection unit (see Battery dis-
connection unit: Removal - Refitting) (80A, Bat-
tery),
- the protection and switching unit (see Protection
and Switching Unit: Removal - Refitting) (87G,
Engine compartment connection unit),
- the radiator cross member mounting (see Radiator
cross member mounting: Removal - Refitting)
(41A, Front lower structure),
- the inlet manifold (see 12A, Fuel mixture, Inlet
distributor: Removal - Refitting, page 12A-75) ,
- the front row upstream oxygen sensor (see 17B,
Petrol injection, Oxygen sensors: Removal -
Refitting, page 17B-17) ,
- the front and rear catalytic pre-converters (see
Front catalytic pre-converter: Removal - Refit-
ting) and (see Rear catalytic pre-converter: Re-
moval - Refitting) .
10A-293
10A