Fuji Electric FRENIC-HVAC User Manual page 333

Code Name
J606 External PID Control 2 (Maximum scale) -999.00 to 0.00 to 9990.00
J607 (Minimum scale) -999.00 to 0.00 to 9990.00
J610
J611 I (Integral time) 0.0 to 3600.0 s
J612 D (Differential time) 0.00 to 600.00 s
J613 (Feedback filter) 0.0 to 900.0 s
J614 (Anti-reset wind-up) OFF: Disable
J615 (ON/OFF control hysteresis width) 0.00 to 9990.00
J616 (Proportional operation output convergent
J617 (Proportion cycle) 1 to 150 s
J618 (Upper limit of PID process output) -10 to 110%
J619 (Lower limit of PID process output) -10 to 110%
J620 (Upper and lower limits) 0: Limit PID output with J618，J619
J621 (Alarm output selection) 0: Absolute-value alarm (PV)
J622 (Upper level alarm (AH)) OFF: Disable
J624 (Lower level alarm (AL)) OFF: Disable
J627 (Feedback error detection mode) 0: Disable (Turns ON output signals (EPV2-ERR) and continues
J629 (Feedback error upper-limit) Auto: 105% equivalent
J630 (Feedback error lower-limit) Auto: -5% equivalent
J631 (Feedback error detection time) 0.0 to 300.0 s
J640 (Manual command) 0: Keypad ( /
J651 External PID Control 3 (Mode selection) 0: Disable
*6 The upper and lower level values are restricted by the maximum and minimum scales.
Data setting range
P (Gain) ON/OFF: ON/OFF control
0.000 to 30.000 times
0.01 to 9990.00 *6
*6
0 to 150%
value)
1: 110%, -10% of PID output with J618 exceeded or less than
J619
1: Absolute-value alarm (PV) (with Hold)
2: Absolute-value alarm (PV) (with Latch)
3: Absolute-value alarm (PV) (with Hold and Latch)
4: Deviation alarm (PV)
5: Deviation alarm (PV) (with Hold)
6: Deviation alarm (PV) (with Latch)
7: Deviation alarm (PV) (with Hold and Latch
8: Absolute-value alarm (SV)
9: Absolute-value alarm (SV) (with Hold)
10: Absolute-value alarm (SV) (with Latch)
11: Absolute-value alarm (SV) (with Hold and Latch)
12: Absolute-value alarm (MV)
13: Absolute-value alarm (MV) (with Hold)
14: Absolute-value alarm (MV) (with Latch)
15: Absolute-value alarm (MV) (with Hold and Latch)
-999.00 to 0.00 to 9990.00
*6
-999.00 to 0.00 to 9990.00
*6
operation.)
1: Enable (Free run stop (PVb trip))
2: Enable (Deceleration and stop (PVb trip))
-999.00 to 0.00 to 9990.00
*6
-999.00 to 0.00 to 9990.00 *6
key)
8: Keypad ( / key) (Balanceless-bumpless)
51: External PID manual command 1(Analog input: Terminals
[12], [C1] and [V2])
52: External PID manual command 2(Analog input: Terminals
[12], [C1] and [V2])
111: Apply external PID control 1 manual command
1: Enable process control (Normal operation)
2: Enable process control (Inverse operation)
11: Enable process control, interlocking with inverter running
(Normal operation)
12: Enable process control, interlocking with inverter running
(Inverse operation)
21: Enable process control by external digital signal (Normal
operation)
22: Enable process control by external digital signal (Inverse
operation)
31: Enable process control by external digital signal, interlocking
with inverter running (Normal operation)
32: Enable process control by external digital signal, interlocking
with inverter running (Inverse operation)
6-23
6.2 Function Code Tables
Change
Data Default Related
when
copying setting page
running
N Y 100.00 6-245
N Y 0.00
Y Y 0.100
Y Y 0.0
Y Y 0.00
Y Y 0.5
Y Y OFF
Y Y 0.00
Y Y 0 6-246
Y Y 30
Y Y 100
Y Y 0
Y Y 0
Y Y 0
Y Y OFF
Y Y OFF
Y Y 0
Y Y Auto
Y Y Auto
Y Y 0.1
N Y 0
N Y 0