Fuji Electric FRENIC-HVAC User Manual page 320

C codes: Control Functions of Frequency
Code Name
C01 Jump Frequency 1
C02 2
C03 3
C04 (Hysteresis width) 0.0 to 30.0 Hz
C05 Multistep Frequency 1
C06 2
C07 3
C08 4
C09 5
C10 6
C11 7
C12 8
C13 9
C14 10
C15 11
C16 12
C17 13
C18 14
C19 15
C21 Pattern Operation (Mode selection) 0: Carry out a single cycle of the specified pattern operation and
C22 Pattern Operation
C23
C24
C25
C26
C27
C28
C30 Frequency Command 2
C31 Analog Input Adjustment for [12]
C32
C33 (Filter time constant) 0.00 to 5.00 s
C34 (Gain base point) 0.00% to 100.00%
C35
C36 Analog Input Adjustment for [C1]
C37
C38 (Filter time constant) 0.00 to 5.00s
C39 (Gain base point) 0.00% to 100.00%
C40 Terminal [C1] Input Range Selection
C41 Analog Input Adjustment for [V2]
C42
C43 (Filter time constant) 0.00 to 5.00 s
C44 (Gain base point) 0.00% to 100.00%
C45
C53 Selection of Normal/Inverse Operation
(Frequency command 1)
C55 Analog Input Adjustment for Terminal [12]
C56 (Bias base point) 0.00 to 100.00%
0.0 to 120.0 Hz
0.00 to 120.00 Hz
stop the inverter output
1: Carry out the specified pattern operation repeatedly and stop
the inverter output upon receipt of a stop command.
2: Carry out a single cycle of the specified pattern operation and
continue to run at the last reference frequency.
(Stage 1) 0.00 to 6000.00 s
FWD/RED 1 to 4
(Stage 2)
(Stage 3)
(Stage 4)
(Stage 5)
(Stage 6)
(Stage 7)
0: Enable / keys on the keypad
1: Voltage input to terminal [12] (-10 to +10 VDC)
2: Current input to terminal [C1] (4 to 20 mA DC)
3: Sum of voltage and current inputs to terminals [12]
and [C1]
5: Voltage input to terminal [V2] (0 to 10 VDC)
7: Terminal command UP/DOWN control
8: Enable / keys on the keypad
(balanceless-bumpless switching available)
10: Pattern operation
-5.0% to 5.0%
(Offset)
(Gain) 0.00% to 200.00%
(Polarity) 0: Bipolar 1: Unipolar
-5.0% to 5.0%
(Offset)
(Gain) 0.00% to 200.00%
0: 4 to 20 mA
1: 0 to 20 mA
-5.0% to 5.0%
(Offset)
(Gain) 0.00% to 200.00%
(Polarity) 0: Bipolar 1: Unipolar
0: Normal operation
1: Inverse operation
-100.00 to 100.00%
(Bias value)
Data setting range
6-10
Change
Data Default Related
when
copying setting page
running
Y Y 0.0 6-125
Y Y 0.0
Y Y 0.0
Y Y 3.0
Y Y 0.00
Y Y 0.00
Y Y 0.00
Y Y 0.00
Y Y 0.00
Y Y 0.00
Y Y 0.00
Y Y 0.00
Y Y 0.00
Y Y 0.00
Y Y 0.00
Y Y 0.00
Y Y 0.00
Y Y 0.00
Y Y 0.00
N Y 0 6-127
Y Y 0.00 6-128
FWD 1
N Y 2 6-130
Y* Y 0.0
Y* Y 100.00
Y Y 0.05
Y* Y 100.00
N Y 1
Y* Y 0.0
Y* Y 100.00
Y Y 0.05
Y* Y 100.00
N Y 0
Y* Y 0.0
Y* Y 100.00
Y Y 0.05
Y* Y 100.00
N Y 1
Y Y 0
Y Y 0.00
Y Y 0.00