Fuji Electric FRENIC-HVAC User Manual page 329

Code Name
J209 (Tuning manipulated value) 10 to 100% (Maximum frequency = 100%)
J210
J211 I (Integral time) 0.0 to 3600.0 s
J212 D (Differential time) 0.00 to 600.00 s
J213 (Feedback filter) 0.0 to 900.0 s
J214 (Anti-reset wind-up) OFF: Disable
J218 (Upper limit of PID process output) Inherit: Depends on setting of F15
J219 (Lower limit of PID process output) Inherit: Depends on setting of F16
J221 PID Control 2 (Alarm output selection) 0: Absolute-value alarm
J222 (Upper level alarm (AH)) OFF: Disable
J223 (Upper level alarm detection hysteresis
J224 (Lower level alarm (AL)) OFF: Disable
J225 (Upper level alarm detection hysteresis
J227 (Feedback failure detection
(Mode selection))
J228 (Feedback failure continuation duration) Cont.: After detection of the failure, continue to run as specified
J229 (Feedback failure upper-limit) Auto: 105% equivalent
J230 (Feedback failure lower-limit) Auto: -5% equivalent
J231 (Feedback failure detection time) 0.0 to 300.0 s
J249 Slow Flowrate Stop Function
(Mode selection)
*
J250 * (Operation level) Auto: Adjust automatically
J251 * (Elapsed time) 0 to 60 s
J256 * (Initiation inhibition time) 0 to 3600 s
J257 * (Cancel frequency) OFF: Disable
J258 * (Cancel deviation level 1) OFF: Disable
J259 * (Cancel delay timer) 0 to 3600 s
J260 * (Cancel deviation level 2) OFF: Disable
J249-J260 are available in the ROM version 1600 or later.

*6 The upper and lower level values are restricted by the maximum and minimum scales.
Data setting range
P (Gain) 0.000 to 30.000 times
0.01 to 9990.00
*6
0.0 to 120.0 Hz
0.0 to 120.0 Hz
1: Absolute-value alarm (with Hold)
2: Absolute-value alarm (with Latch)
3: Absolute-value alarm (with Hold and Latch)
4: Deviation alarm
5: Deviation alarm (with Hold)
6: Deviation alarm (with Latch)
7: Deviation alarm (with Hold and Latch)
50: Absolute value alarm (Cancel PID control)
-999 to 0.00 to 9990.00 *6
0.00 to 9990.00 *6
width)
-999 to 0.00 to 9990.00
*6
0.00 to 9990.00
*6
width)
0: Disable (Turns ON output signals (PV2-ERR) and continues
operation.)
1: Enable (Free run stop (PV2 trip))
2: Enable (Deceleration and stop (PV2 trip))
3: Enable (Continuation of operation at the maximum frequency
(upper limit frequency))
4: Enable (Continuation of operation at the minimum frequency
(lower limit frequency))
5: Enable (Continuation of operation at the frequency used when
failure is detected.)
by J227. After stop (output shutoff), cause a PV2 trip.
0 to 3600 s
-999.00 to 0.00 to 9990.00
*6
-999.00 to 0.00 to 9990.00 *6
OFF: Disable
1: Manual operation (stop judgment: MV)
2: Manual operation (stop judgment: PV)
0.00 to 120.00 Hz when J149 = MV
0.00 to 9990.00 when J149 = PV
0.0 to 120.0 Hz
0.01 to 9990.00
*6
0.01 to 9990.00
*6
6-19
6.2 Function Code Tables
Change
when
running
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
N
Y
*6
Y
Y
Y
Y
Y
Y
Data Default Related
copying setting page
Y 10% 6-215
Y 0.100
Y 0.0
Y 0.00
Y 0.5
Y OFF
Y Inherit 6-216
Y Inherit
Y 0
Y OFF
Y 0.00
Y OFF
Y 0.00
Y 0
Y Cont.
Y Auto
Y Auto
Y 0.1
Y OFF
Y Auto
Y 0
Y 0
Y 0.0
Y OFF
Y 0
Y OFF