Fuji Electric FRENIC-HVAC User Manual page 323

Code Name
H50 Non-linear V/f Pattern 1 (Frequency) OFF: Cancel, 0.1 to 120.0 Hz
H51
H52 Non-linear V/f Pattern 2 (Frequency) OFF: Cancel, 0.1 to 120.0 Hz
H53
H56 Deceleration Time for Forced Stop
H61 Multistep Frequency + UP/DOWN Control
(Initial frequency setting)
H63 Low Limiter (Mode selection) 0: Limit by F16 (Frequency limiter: Low) and continue to run
H64 (Lower limiting frequency) Inherit: Depends on F16 (Frequency limiter, Low)
H68 Slip Compensation 1
(Operating conditions)
H69 Automatic Deceleration
(Mode selection)
H70 Overload Prevention Control
H71 Deceleration Characteristics
H72 Main Power Down Detection
(Mode selection)
H76 Torque Limiter for Braking
(Frequency increment limit)
H77 Service Life of DC Link Bus Capacitor
(Remaining time)
H78 Maintenance Interval (M1)
H79 Preset Startup Count for Maintenance (M1) OFF: Disable
H80 Output Current Fluctuation Damping Gain
for Motor 1
H89 Reserved *5
H90 Reserved *5
H91 Current Input Wire Break Detection
H92 Continuity of Running
H93
H94 Cumulative Motor Run Time 1
H95 DC Braking
(Braking response mode)
H96 STOP Key Priority/Start Check Function
H97 Clear Alarm Data
H98 Protection/Maintenance Function
(Mode selection)
*5 These function codes are reserved for particular manufacturers. Unless otherwise specified, do not access these function codes.
Data setting range
(Voltage) 0-240 V: Output an AVR-controlled voltage (230 V class series)
0-500 V: Output an AVR-controlled voltage (460 V class series)
0-690 V: Output an AVR-controlled voltage (575 V class series)
(Voltage) 0-240 V: Output an AVR-controlled voltage (230 V class series)
0-500 V: Output an AVR-controlled voltage (460 V class series)
0-690 V: Output an AVR-controlled voltage (575 V class series)
0.00 to 3600 s
1: Last UP/DOWN command value on releasing the run
command
13 to 106: Multistep frequency + UP/DOWN command (Initial
value to be preserved)
1: If the output frequency lowers below the one limited by F16
(Frequency limiter: Low), decelerate to stop the motor.
0.1 to 60.0 Hz
0: Enable during ACC/DEC and at base frequency or above
1: Disable during ACC/DEC and enable at base frequency or
above
2: Enable during ACC/DEC and disable at base frequency or
above
3: Disable during ACC/DEC and at base frequency or above
0: Disable
2: Torque limit control with Force-to-stop if actual deceleration
time exceeds three times the specified one
3: DC link bus voltage control with Force-to-stop if actual
deceleration time exceeds three times the specified one
4: Torque limit control with Force-to-stop disabled
5: DC link bus voltage control with Force-to-stop disabled
OFF: Cancel
Inherit: Follow the selected deceleration time
0.01 to 100.00 Hz/s
0: Disable
1: Enable
0: Disable
1: Enable
0.0 to 120.0 Hz
0 to 43800 (in units of 10 hours)
OFF: Disable
10 to 99990 (in units of 10 hours)
1 to 65535
0.00 to 1.00
0, 1
0, 1
OFF: Disable, 0.1 to 60.0 s
(P) Auto: Adjust automatically
0.000 to 10.000 times
(I) Auto: Adjust automatically
0.010 to 10.000 s
0 to 99990 (The cumulative run time can be modified or reset in
units of 10 hours.)
0: Slow
1: Quick
Data STOP key priority
0: Disable
1: Enable
2: Disable
3: Enable
0: Disable
1: Enable (Setting "1" clears alarm data and then returns to "0.")
0 to 255
Bit 0: Lower the carrier frequency automatically
Bit 1: Detect input phase loss
Bit 2: Detect output phase loss
Bit 3: Select life judgment threshold of DC link bus capacitor
(0: Factory default level; 1: User setup level)
Bit 4: Judge the life of DC link bus capacitor
Bit 5: DC fan lock detection
Bit 7: Switch NEMA/UL Type 1, NEMA/UL Type 12 enclosure
(0: NEMA/UL Type 1; 1: NEMA/UL Type 12)
6-13
6.2 Function Code Tables
Change
when
running
N
N
N
N
Y
N
Y
Y
N
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
N
Y
Start check function Y
Disable
Disable
Enable
Enable
Y
Y
(0: Disabled; 1: Enabled)
(0: Disabled; 1: Enabled)
(0: Disabled; 1: Enabled)
(0: Disabled; 1: Enabled)
(0: Disabled; 1: Enabled)
Data Default Related
copying setting page
Y OFF 6-159
Y1 0
Y OFF
Y1 0
Y 20.0
Y 1 6-160
Y 0 6-164
Y 2.0
Y 0
Y 0
Y OFF 6-165
Y 0 6-166
Y 1
Y 5.0
N NEMA/UL 6-167
Type 1/12:
43800
N
UL open
type :
87600
N OFF 6-168
Y 0.20
Y 1 6-169
Y 0
Y OFF
Y1 Auto
Y1 Auto
N -
Y 1
Y 3 6-170
N 0
Y UL open 6-171
type ,
NEMA/UL
Type 1
: 19
NEMA/UL
Type 12
: 147