Fuji Electric FRENIC-HVAC User Manual page 331

Code Name
J510 External PID Control 1
J511 I (Integral time) 0.0 to 3600.0 s
J512 D (Differential time) 0.00 to 600.00 s
J513 (Feedback filter) 0.0 to 900.0 s
J514 (Anti-reset wind-up) OFF: Disable
J515 (ON/OFF control hysteresis width) 0.00 to 9990.00
J516 (Proportional operation output convergent
J517 (Proportional cycle) 1 to 150 s
J518 (Upper limit of PID process output) -10 to +110%
J519 (Lower limit of PID process output) -10 to +110%
J520 (Upper and lower limits) 0: Limit PID output with J518, J519
J521 (Alarm output selection) 0: Absolute-value alarm (PV)
J522 (Upper level alarm (AH)) OFF: Disable
J524 (Lower level alarm (AL)) OFF: Disable
J527 (Feedback error detection mode) 0: Disable (Turns ON output signals (EPV1-ERR) and continues
J529
(Feedback error upper-limit)
J530 (Feedback error lower-limit) Auto: -5% equivalent
J531 (Feedback error detection time) 0.0 to 300.0 s
J540 (Manual command) 0: Keypad ( /
J550 External PID Multistep Command
(Mode selection)
J551 (Multistep command 1) -999.00 to 0.00 to 9990.00
J552 (Multistep command 2) -999.00 to 0.00 to 9990.00
J553 (Multistep command 3) -999.00 to 0.00 to 9990.00
*6 The upper and lower level values are restricted by the maximum and minimum scales.
Data setting range
P (Gain) ON/OFF: ON/OFF control
0.000 to 30.000 times
0.00 to 9990.00
*6
*6
0 to 150%
value)
1: 110%, -10% of PID output with J518 exceeded or less than
J519
1: Absolute-value alarm (PV) (with Hold)
2: Absolute-value alarm (PV) (with Latch)
3: Absolute-value alarm (PV) (with Hold and Latch)
4: Deviation alarm (PV)
5: Deviation alarm (PV) (with Hold)
6: Deviation alarm (PV) (with Latch)
7: Deviation alarm (PV) (with Hold and Latch
8: Absolute-value alarm (SV)
9: Absolute-value alarm (SV) (with Hold)
10: Absolute-value alarm (SV) (with Latch)
11: Absolute-value alarm (SV) (with Hold and Latch)
12: Absolute-value alarm (MV)
13: Absolute-value alarm (MV) (with Hold)
14: Absolute-value alarm (MV) (with Latch)
15: Absolute-value alarm (MV) (with Hold and Latch)
-999.00 to 0.00 to 9990.00
*6
-999.00 to 0.00 to 9990.00 *6
operation.)
1: Enable (Free run stop (PVA trip))
2: Enable (Deceleration and stop (PVA trip))
Auto: 105% equivalent
-999.00 to 0.00 to 9990.00
*6
-999.00 to 0.00 to 9990.00
*6
key)
8: Keypad ( / key) (Balanceless-bumpless)
51: External PID command 1 (Analog input: Terminals [12], [C1]
and [V2])
Bit 0: Enable multistep command under external PID control 1
Bit 1: Enable multistep command under external PID control 2
Bit 2: Enable multistep command under external PID control 3
6-21
6.2 Function Code Tables
Change
Data Default Related
when
copying setting page
running
Y Y 0.100 6-229
Y Y 0.0
Y Y 0.00
Y Y 0.5
Y Y OFF 6-233
Y Y 0.00 6-234
Y Y 0 6-235
Y Y 30 6-236
Y Y 100 6-237
Y Y 0
Y Y 0
Y Y 0 6-238
Y Y OFF
Y Y OFF
Y Y 0 6-241
Y Y Auto
Y Y Auto
Y Y 0.1
N Y 0 6-243
N Y 0 6-244
Y Y 0.00
Y Y 0.00
Y Y 0.00