Mitsubishi A1SD75M3 User Manual page 737

Outline of installation, wiring and maintenance
......................................................................... 4-2
Outline of starting .......................................... 1-16
Outline of stopping ........................................ 1-18
Outline of zero point return control ................. 8-2
Override function ......................................... 12-50
Override program .......................................... 6-17
[P]
P RATE (explanation of terms)........ Appendix-41
PANCAKE MOTOR (explanation of terms)
.......................................................... Appendix-41
PARAMETER (explanation of terms)
.......................................................... Appendix-42
PI-PID switching position droop (
................................................. 5-67, 87, 101, 111
PLC CPU ....................................................... A-16
PLC CPU memo area ..................................... 7-3
PLC READY signal ....................................... 3-14
PLC READY signal [Y1D] ON program........ 6-14
POSITION CONTROL (explanation of terms)
.......................................................... Appendix-42
POSITION LOOP GAIN (explanation of terms)
.......................................................... Appendix-42
POSITION LOOP MODE (explanation of terms)
.......................................................... Appendix-42
POSITIONING (explanation of terms)
.......................................................... Appendix-42
POSITIONING COMPLETE SIGNAL
(explanation of terms) ...................... Appendix-42
POSITIONING DATA (explanation of terms)
.......................................................... Appendix-42
POSITIONING PARAMETER (explanation of
terms)................................................ Appendix-42
POSITIONING START (explanation of terms)
.......................................................... Appendix-43
PTP Control (explanation of terms)
.......................................................... Appendix-43
PU (explanation of terms) ................ Appendix-43
PULSE (explanation of terms) ......... Appendix-43
Parameter ( Da.13 )..................................... 5-130
Parameter 1 ( Da.17
Parameter 2 ( Da.18
Parameter area ............................................... 7-3
Parameter error (No. 1 to 15) (
..................................................................... 5-164
Parameter error (No. 16 to 31) (
..................................................................... 5-164
Pr.134 )
).................................. 5-135
).................................. 5-135
Md.113 )
Md.114 )
Parameter error (No. 32 to 36) (
......................................................................5-164
Parameter initialization program....................6-19
Parameter initialization request (
......................................................................5-172
Parameter setting program............................6-12
Performance specifications .............................3-3
Peak load ratio (
Peripheral device connection connector .........4-4
Personal computer........................................ A-16
Position loop gain 1 (
Position loop gain 1 (
............................................. 5-63, 73, 83, 93, 109
Position loop gain 2 (
Position loop gain 2 (
............................................. 5-63, 73, 83, 93, 109
Positioning address pass mode ..................12-20
Positioning address/movement amount (
......................................................................5-116
Positioning complete........................................9-5
Positioning complete signal ...........................3-13
Positioning complete signal output time (
........................................................................5-44
Positioning control operation program ............6-9
Positioning data No. (
Positioning data No. 101 to 600 setting .....7-9,16
Positioning data No. being executed] (
......................................................................5-158
Positioning data area (No. 1 to 100) ...............7-3
Positioning data area (No. 101 to 600) ...........7-3
Positioning data being executed (
......................................................................5-158
Positioning data setting program...................6-12
Positioning operation speed override (
......................................................................5-176
Positioning program examples ......................6-12
Positioning start No. (
Positioning start No. setting program ............6-14
Positioning start information area (No.7000)
..........................................................................7-3
Positioning start information area
(No.7001 to 7010) ............................................7-3
Positioning start information setting program
........................................................................6-13
Positioning start signal...................................3-14
Positioning start signal input program ...........6-15
Positioning starting point No. (
Positioning to the zero point ..........................8-21
Index - 7
Md.115
Cd.10
Md.119 ).............................5-166
) .....................5-162
Md.107
)
Pr.113
) .....................5-162
Md.109
Pr.115 )
Cd.5 ) .....................5-170
Md.54
Md.56
Cd.18
Cd.11 )......................5-174
) .......5-182
Cd.31
)
)
Da.5 )
Pr.41 )
)
)
)