Advertisement
GLASS
IN
AND OUT
FORE AND AFT
IN
AND OUT
"
REG
STO
D OUT
REG
STO
IN AND' OUT
DOWN STOP
SCREW AND WASHER
NK929
Fig. I 1 2 4 u a r f e r Window Adiustments-
Hard Top (AP ModelsJ
at center of the track.
ing the track to the belt reinforcement.
Installation
(1)
Insert the track assembly into the door through
the large access opening in the door inner panel (Fig.
111).
(2) Align the upper attaching screw hole in the
track with the attaching hole in the belt line and the
hole in the lower track support with the bottom
while inserting the stud on the center of the track
through the hole in the door inner panel.
(3) Install the screw and washer assembly at the
top finger tight only.
(4) Install the screw and washer assembly, and wir-
ing clip if used, to the bottom support finger tight only.
(5) Install the sleeve adjusting nut on the track stud.
(6)
Install the door glass assembly and adjust for
(7)
Install the door water shield, trim panel and in-
(4) Remove the screw and washer assembly attach-
alignment and ease of operation.
side handles.
Adjustments IAP Models)
Refer to Figure 112 for the adjustment points and
methods of adjustment.
(1)
Remove the regulator handle, trim panel and
water shield.
(2) Close the door and adjust the upper rear track
attachments so the rear of the window lightly touches
the cat whiskers. To move window inboard, turn the
sleeve nut clockwise and to move outboard turn the
sleeve nut counterclockwise.
(3) Run the window up, seating the top of glass
fully against the roof rail weatherstrip and the front
of the window flush with the top of the front door
window.
QUARTER WINDOWS (Hard Top)
(4) Adjust the upper front track attachment
so
the
front of the window is aligned with the rear of the
front door window at the belt line. Turn the sleeve
nut clockwise to move the window in and counter-
clockwise to move the window out.
(5) Adjust the lower front track attachment so the
front of the window is aligned with the rear of the
front door window at the roof rail. Turn the sleeve
nut counterclockwise to move the window in and
clockwise to move the window out.
(6) Adjust the pivot bracket
so the top of the win-
dow is fully against and parallel to the roof rail
weatherstrip. To raise the front of the window, lower
the front of the pivot bracket.
(7)
Move the upper front track attachment forward
so
the weatherstrip of the window is against the front
door window.
(8)
Position the up stops against the lower frame
of
the window.
(9) Run the window down
so
the top of the glass
is
even with or slightly below the belt line.
(10) Adjust the lower rear track attachment
so
the
"boss" is against the outboard side of the inside panel.
(11) On manually operated regulators, position the
stop on the regulator plate against the stop on
the regulator sector,
On
electrically operated regu-
lators, position the stop against the bumper (Fig. 112).
(12) Move the
front
track center support
so it is
positioned against the brace and tighten the screw se-
curely.
(13) Operate the window, inspect alignment and
test
for ease of operation.
(14) Install the water shield, trim panel and regula-
tor handle.
IAR Models)
methods of adjustment for the quarter glass.
Refer to Figure 113 for the adjustment points and
Adjustments IAV Models Except AVP29J
(1)
With the hardware, trim panel and water shield
removed, run the window up until the glass is parallel
to the rear of the front door glass.
(2) Position the up stop (Fig. 114) down against the
regulator arm and tighten securely in place.
(3)
Roll the glass
2 / 3
way down, loosen the screw
at the front of the quarter window and move the
glass assembly on the hinge upward and tighten the
screw.
(4) Roll the glass up and inspect the seal between
the rear edge of the door glass and the front edge
of the quarter window.
(5) If necessary readjust as outlined in steps 1, 2
and 3.
(6) With the door open, loosen the three screws at
the front of the quarter panel top edge and move the
Hide quick links:
Advertisement
