Advertisement
GLASS
23-47
door lock knob, trim panel and water shield.
(2)
With the door glass in the down position disen-
gage the division bar from the lower adjusting bracket
(Fig. 98).
(3) Remove the lock nut of the tilting adjusting
screw and turn the adjusting screw clockwise to dis-
engage the screw from the door frame bracket.
(4)
Remove the two attaching screws from the base
of the vent frame.
(5) Tilt the vent frame to the rear and remove the
vent frame assembly up out of the door.
lnst allation
(1) With the
tilt
adjusting screw bottomed in the
vent frame and the door glass down, insert the vent
frame into the door.
(2)
Turn the tilt adjusting screw counter-clockwise
and engage it into the bracket of the door.
(3) Install the two attaching screws in the base of
the vent frame finger tight.
(4)
Attach the lower end of the division bar to the
adjusting bracket.
(5) Refer to Figure 98 for the vent frame adjust-
ment points and methods.
(6) Install the water shield, trim panel, and inside
door hardware.
IAV Models)
(1) Remove the door interior trim and hardware.
(2) With the door glass in the down position, re-
move the division bar adjusting screw (Fig. 100).
(3) Remove the two vent frame attaching screws
from the front of the door.
(4)
Disconnect the cat whiskers far enough for
clearance of the division bar when
it
is removed.
(5) Tilt the vent frame to the rear and remove from
the door.
(6)
The tilt adjustment screw should be in lowest
position, when installing the vent wing assembly.
(7) With the vent wing tilted toward the rear of the
door, guide the division bar and the tilt adjustment
bracket down into the door.
(8) Install the division bar adjusting screw and
the vent wing to door panel screws.
(9)
Position the tilt adjustment screw in the door
inner panel and install the lock nut.
(10) Install the two vent frame screws (in the front
of the door).
(11)
Adjust the vent wing and install the door in-
terior trim and hardware.
Door Glass
Removal fAR Models)
lock knob, trim panel and water shield.
(1)
Remove the inside handles, arm rest, remote
(2)
Place the glass in the down position and insert
a screwdriver under the retainer ring and pry the
retainer off of both regulator arm studs.
(3) Remove the regulator studs from the glass low-
er channel.
(4)
Remove the two up stops.
(5) Remove the door glass up through the door
frame.
Installation
(1) With the glass tilted slightly to the rear insert
the glass into the front and rear run channel and
lower the glass down into the door.
(2) Lubricate the slides of the glass lower channel.
(3) Insert the regulator arm studs into the slides of
(4)
Install the retainers over the end of the regula-
(5) Install the two up stops and adjust the door
(6)
Install the water shield, trim panel and inside
the glass lower channel.
tor studs.
glass.
door hardware.
Removal fAV Models)
watershield.
(1)
Remove the door interior trim, hardware and
(2)
Lower the window and remove the glass up stop.
(3) Remove the clip from the regulator forward
(4)
Loosen the rear track adjusting screws and re-
(5) Remove the regulator rear arm from the lift
(6) Remove the glass from the door.
(7) Remove the lift bracket and bushing from the
arm pivot (Fig. 100).
move the glass from the channel.
bracket channel.
door glass (Fig. 103).
Installation
(1)
Install the lift bracket and the forward regulator
*GASKET
RIVET
I
I
GLASS AND FRAME
LIFT BRACKET
Fig. 103-Hard
Top Door
Glass Attachment
IAV Models)
Hide quick links:
Advertisement
