Xerox ColorQube 9303 Series Service Manual page 55

• The marking unit driver PWB, PL 92.10 Item
ler PWB
• Repair the wiring as necessary, REP 1.1
• If necessary, install a new IME controller PWB,
Marking Unit Driver PWB
• To view the +24V distribution from the
• For +24V faults on the marking unit driver
– WD 9.10
– WD 9.12
• The solenoid patch PWB, PL 93.10 Item 9
driver PWB:
• Repair the wiring as necessary, REP
• If necessary, install a new marking unit driver PWB,
Solenoid Patch PWB
• To view the +24V distribution from the
• For +24V faults on the solenoid patch
– WD 9.14
– WD 9.15
• The components that follow are driven from +24V from the
– Purge solenoid valves 1 to 4 SOL93-059, 060, 061, 062, part of
– Black ink solenoid valves 5 to 8 SOL063,064, 065, 066, part of
– Yellow ink solenoid valves 9 to 12,SOL067, 068, 069, 070, part of
– Cyan ink solenoid valves 13 to 16 SOL071, 072, 073, 074, part of
– Magenta ink solenoid valves 17 to 20 SOL075, 076, 077, 078, part of
10
• Repair the wiring as necessary, REP
• If necessary, install a new solenoid patch PWB,
Power Distribution PWB
• To view the +24V distribution from the
• For +24V faults on the power distribution
– WD 1.6
– WD 1.7
• Check for +24V on both sides of fuse F8 on the
present, check the following wiring:
– Between PJ8 pins 7 and 9 on the
the scanner PWB.
– Between PJ8 pins 1, 3 and 5 on the
3 on the DADH PWB.
• Repair the wiring as necessary, REP
• If necessary, install a new power distribution PWB,
Scanner PWB
• To view the +24V distribution from the
• For +24V faults on the scanner PWB, refer to:
– WD 6.1
ColorQube® 9303 Family
4, is driven from +24V from the IME control-
PL 92.10 Item 1.
IME controller PWB, refer to WD 9.7.
PWB, refer to:
is driven from +24V from the marking unit
1.1.
PL 92.10 Item 4.
marking unit driver PWB, refer to WD 9.12.
PWB, refer to:
solenoid patch PWB:
PL 93.10 Item
PL 93.10 Item 10
PL 93.10 Item 10
PL 93.10 Item 10
PL 93.10 Item
1.1.
PL 93.10 Item 9.
power supply unit, refer to WD 1.5
PWB, refer to:
power distribution PWB. If +24V is not
power distribution PWB and PJ920 pins 1 and 3 on
power distribution PWB and PJ188 pins 1, 2 and
1.1.
PL 3.11 Item 1.
power distribution PWB, refer to WD 1.7
– WD 6.2
• The components that follow are driven from +24V from the
– LED exposure lamp(s),
• Repair the wiring as necessary,
• If necessary, install a new scanner PWB,
DADH PWB
• To view the +24V distribution from the
• For +24V faults on the DADH
– WD 5.1
– WD 5.2
• The components that follow are driven from +24V from the
– DADH CVT motor MOT05-099,
– DADH feed motor MOT05-074,
– DADH duplex solenoid SOL05-100,
– Nudger motor MOT05-098,
– DADH feed clutch CL05-062,
– DADH cover interlock switch S05-212,
• Repair the wiring as necessary,
• If necessary, install a new DADH PWB,
10.
Media Path Driver PWB
• To view the +24V distribution from the
• For +24V faults on the media path driver
– WD 8.2
– WD 8.3
– WD 8.4
– WD 8.5
• The components that follow are driven from +24V from the
– Bypass feed motor (M7) MOT74-420,
– 3 tray module PWB,
– Tray 5 control PWB,
– OCT, PL 12.00 Item
– LCSS PWB, PL 12.75 Item
– HVF PWB, PL 12.140 Item
• Repair the wiring as necessary,
• If necessary, install a new media path driver PWB,
3 Tray Module PWB
• To view the +24 distribution from the
• For +24V faults on the three trays module PWB, refer to:
– WD 7.3
– WD 7.4
– WD 7.5
• The +24V LED on this PWB is shown in
• The components that follow are driven from +24V from the
February 2013
2-31
scanner
PL 62.15 Item 2.
REP 1.1
PL 62.16 Item 8
power distribution PWB, refer to
PWB, refer to:
DADH
PL 5.25 Item 9.
PL 5.15 Item 16.
PL 5.30 Item 3.
PL 5.15 Item 5.
PL 5.15 Item 9.
PL 5.15 Item 11.
REP 1.1
PL 5.10 Item 5.
power supply unit, refer to WD 1.5
PWB, refer to:
media path driver
PL 74.10 Item 2.
PL 73.16 Item 4.
PL 75.68 Item 8.
1.
1.
2.
REP 1.1.
PL 1.15 Item 5
media path driver PWB, refer to
WD 7.3
3 tray module
PWB:
WD 1.7.
PWB:
PWB:
WD 8.2
PWB:
Status Indicator RAPs
01H