Table of Contents
Advertisement
–
Enclosure Fan,
PL 1.15 Item
6.
–
Marking unit cooling fan,
PL 1.15 Item
–
Abatement fan assembly,
PL 94.20 Item
–
Cleaning unit,
PL 94.10 Item
21.
–
Stripper Jam Clearance LED assembly,
–
Registration/preheat Interface PWB,
•
Repair the wiring as necessary,
REP
•
If necessary, install a new drum driver PWB,
above.
Cleaning Unit
•
To view the +12V distribution from the
•
For +12V faults on the cleaning unit PWB, refer to
•
Repair the wiring as necessary,
REP
•
If necessary, install a new cleaning unit,
NOTE: The cleaning unit PWB is not spared individually, the next highest assembly is the
cleaning unit.
Media Path Driver PWB
•
To view the +12V distribution from the
•
For +12V faults on the
media path driver
–
WD 8.1
–
WD 8.5
•
The components that follow are driven from +12V from the
–
Exit illuminator,
PL 10.15 Item
–
Horizontal illuminator,
PL 82.15 Item
–
Registration/preheat illuminator PWB,
–
Registration/preheat interface PWB,
•
Repair the wiring as necessary,
REP
•
If necessary, install a new media path driver PWB,
the list above.
Registration/Pre-heat Interface PWB
•
To view the +12V distribution from the
•
To view +12 V distribution from
media path driver
•
For +12V faults on the registration/pre-heat interface PWB, refer to
•
The components that follow are driven from +12V from the reg/preheat interface PWB:
–
Registration scan bar Q89-005,
–
Registration/preheat air pumps MOT88-008,
•
Repair the wiring as necessary,
REP
•
If necessary, install a new registration/pre-heat interface PWB,
of the items in the list above
Power Distribution PWB
•
To view the +12V distribution from the
•
For +12V faults on the
power distribution
–
WD 1.6
ColorQube® 9303 Family
23.
11.
PL 10.10 Item 10
PL 88.10 Item 10
1.1.
PL 1.15 Item
4, or one of the items in the list
drum driver
PWB, refer to
WD
9.4.
WD
9.19.
1.1.
PL 94.10 Item
21.
power supply
unit, refer to
WD
1.5.
PWB, refer to:
media path driver
16.
11.
PL 82.15 Item
17.
PL 88.10 Item
10.
1.1.
PL 1.15 Item
5, or one of the items in
drum driver
PWB, refer to
WD
9.2.
PWB, refer to
WD
8.1.
WD
8.6.
PL 88.10 Item
2.
PL 88.10 Item
5.
1.1.
PL 88.10 Item
power supply
unit, refer to
WD
1.5.
PWB, refer to:
–
WD 1.7
•
Check for +12V on both sides of fuse F2 on the
present, check the wiring between PJ8 pin 11 on the
pin 5 on the
scanner
•
Repair the wiring as necessary,
•
If necessary, install a new power distribution PWB,
Single Board Controller PWB
•
To view the +3.3V distribution from the
•
For +3.3V faults on the
–
WD 3.1
–
WD 3.2
•
If necessary repair the wiring,
PL 62.16 Item
7.
•
If necessary, install a new single board controller PWB,
Scanner PWB
•
To view the +12V distribution from the
•
For +12V faults on the
–
WD 6.1
–
WD 6.3
•
The scan carriage,
•
Repair the wiring as necessary,
•
If necessary, install a new scanner PWB,
PWB:
Full Width Array
•
To view the +12V distribution from the
•
For +12V faults on the full width array, refer to
•
Repair the wiring as necessary,
•
If necessary, install a new scan carriage assembly,
UI PWB
•
To view the +12V distribution from the
•
For +12V faults on the
•
If necessary repair the wiring,
•
If necessary, install a new user interface control PWB,
status PWB,
PL 2.10 Item
Quad Wave Amp PWB
•
To view the +12V distribution from the
•
For +12V faults on
•
Repair the wiring as necessary,
•
If necessary, install a new quad wave amp PWB,
10, or one
Printheads 1 to 4
•
To view the +12 V distribution from the
•
For +12V faults on the printhead, refer to
•
If necessary, install a new printhead
February 2013
2-27
power distribution
power distribution PWB
PWB.
REP
1.1.
PL 3.11 Item
power distribution
PWB, refer to
single board controller
PWB, refer to:
REP 1.1
or install a new DADH/IIT power comms harness,
PL 3.11 Item
power distribution
PWB, refer to
scanner
PWB, refer to:
PL 62.15 Item 6
is driven from +12V from the
REP
1.1.
PL 62.16 Item
8.
scanner
PWB, refer to
WD
6.3.
REP
1.1.
PL 62.15 Item
single board controller
UI
PWB, refer to
WD
3.2.
REP
1.1.
PL 2.10 Item 2
4.
IME controller
PWB, refer to
quad wave amp
PWB, refer to
WD
9.13.
REP
1.1.
PL 92.10 Item
IME controller
PWB, refer to
WD 9.20
and
WD
PL 91.20 Item 2
or
PL 91.25 Item
PWB. If +12V is not
and PJ920
1.
WD
1.6.
13.
WD
1.7.
scanner
PWB:
WD
6.3.
1.
PWB, refer to
WD 3.2
or user interface
WD
9.5.
3.
WD 9.5
and
WD
9.6.
9.21.
2.
Status Indicator RAPs
01E
Advertisement
Chapters
Table of Contents
