Function - Canon imagePRESS 1135 Series Service Manual

FEEDER> ADJUST
ADJMSCN2 Zoom adj in 2-sided main scan way: back
Lv.1 Details Make a fine adjustment of the backside image magnification in main
scanning direction at the time of DADF duplex scanning.
When the value is incremented by 1, the image is reduced by 0.1 %
in main scanning direction.
Use case When a displacement occurred to the front/backside image
magnification at the time of duplex scanning
Adj/set/operate method Enter the setting value and press the OK key.
Display/adj/set range -10 to 10
Unit 0.1 %
Default value 0
ADJSSCN1 Zoom adj in 2-sided sub scan way: front
Lv.1 Details Make a fine adjustment of the front side image magnification in sub
scanning direction at the time of DADF duplex scanning.
When the value is incremented by 1, the image is reduced by 0.1 %
in sub scanning direction.
Use case When a displacement occurred to the front/backside image
magnification at the time of duplex scanning
Adj/set/operate method Enter the setting value and press the OK key.
Display/adj/set range -10 to 10
Unit 0.1 %
Default value 0
ADJSSCN2 Zoom adj in 2-sided sub scan way: back
Lv.1 Details Make a fine adjustment of the backside image magnification in sub
scanning direction at the time of DADF duplex scanning.
When the value is incremented by 1, the image is reduced by 0.1 %
in sub scanning direction.
Use case When a displacement occurred to the front/backside image
magnification at the time of duplex scanning
Adj/set/operate method Enter the setting value and press the OK key.
Display/adj/set range -10 to 10
Unit 0.1 %
Default value 0
8
Service Mode > FEEDER > FUNCTION
T-8-109
8 Service Mode > FEEDER > FUNCTION

FUNCTION

FEEDER> FUNCTION
SENS-INT Initialization of DADF sensor
Lv.1 Details Initialize DADF sensors.
Use case At the time of replacement of the reader controller PCB / post-
separation sensor 1 (SR2) / post-separation sensor 2 (SR3) / post-
separation sensor 3 (PCB2) / registration sensor (PCB3) / read
sensor 1 (PCB4) / read sensor 2 (SR5)
Adj/set/operate method Enter the value and press the OK key.
MTR-CHK Specifying DADF operation motor
Lv.1 Details Specify the DADF motor to operate.
The motor is activated by MTR-ON.
Use case At the time of operation check
Adj/set/operate method Enter the value and press the OK key.
Display/adj/set range 0 to 9
0: Pickup motor (M1), 1: Feed motor (M2), 2: Registration motor (M3),
3: Read motor (M4), 4: Delivery motor (M5), 5: Separation motor 1
(M6), 6: Separation motor 2 (M7), 7: Tray up/down motor (M8), 8:
Glass moving motor (M9), 9: Pickup unit up/down motor (M10)
Related service mode FEEDER> FUNCTION> MTR-ON
TRY-A4 Adj of DADF tray width detect ref 1: A4
Lv.1 Details Automatically adjust the paper width detection reference point 1 for
the DADF document feed tray. (A4)
Use case • At the time of replacement of the document width volume (VR)
• At the time of replacement of the reader controller PCB / clearing
of RAM data
TRY-A5R Adj of DADF tray width detect ref 2: A5R
Lv.1 Details Automatically adjust the paper width detection reference point 2 for
the DADF document feed tray. (A5R)
Use case • At the time of replacement of the document width volume (VR)
• At the time of replacement of the reader controller PCB / clearing
of RAM data
TRY-LTR Adj of DADF tray width detect ref 1: LTR
Lv.1 Details Automatically adjust the paper width detection reference point 1 for
the DADF document feed tray. (LTR)
Use case • At the time of replacement of the document width volume (VR)
• At the time of replacement of the reader controller PCB / clearing
of RAM data
TRY-LTRR Adj of DADF tray width detect ref2: LTRR
Lv.1 Details Automatically adjust the paper width detection reference point 2 for
the DADF document feed tray. (LTRR)
Use case • At the time of replacement of the document width volume (VR)
• At the time of replacement of the reader controller PCB / clearing
of RAM data
8-424
8-424