Canon imagePRESS 1135 Series Service Manual page 1372

SORTER> ADJUST
10RGT-1 Adj 10sheet stack top right angle:trimmr
Lv.2 Details To adjust the cut angle on the top side when the right angle is not
accurate at 3-direction cut for 10-sheet stack.
As the value is changed by 1, the rotation degree is changed by
0.1 mm.
+: rotation degree is increased, cut angle gets smaller
-: rotation decree is decreased, cut angle gets larger
Use case When the right angle is not accurate after the stack is cut
Display/adj/set range -100 to 100
Unit 0.1 mm
Default value 0
10RGT-2 Adj 10sheet stack rear right angle:trmmr
Lv.2 Details To adjust the cut angle on the tail side when the right angle is not
accurate at 3-direction cut for 10-sheet stack.
As the value is changed by 1, the rotation degree is changed by
0.1 mm.
+: rotation degree is increased, cut angle gets smaller
-: rotation decree is decreased, cut angle gets larger
Use case When the right angle is not accurate after the stack is cut
Display/adj/set range -100 to 100
Unit 0.1 mm
Default value 0
10RGT-3 Adj 10sheet stack fore right angle:trmmr
Lv.2 Details To adjust the cut angle on the fore edge side when the right angle is
not accurate at 3-direction cut for 10-sheet stack.
As the value is changed by 1, the rotation degree is changed by
0.1 mm.
+: rotation degree is increased, cut angle gets smaller
-: rotation decree is decreased, cut angle gets larger
Use case When the right angle is not accurate after the stack is cut
Display/adj/set range -100 to 100
Unit 0.1 mm
Default value 0
200RGT-1 Adj 200sheet stack top right angle:trmmr
Lv.2 Details To adjust the cut angle on the top side when the right angle is not
accurate at 3-direction cut for 200-sheet stack.
As the value is changed by 1, the rotation degree is changed by
0.1 mm.
+: rotation degree is increased, cut angle gets smaller
-: rotation decree is decreased, cut angle gets larger
Use case When the right angle is not accurate after the stack is cut
Display/adj/set range -100 to 100
Unit 0.1 mm
Default value 0
8
Service Mode > SORTER > ADJUST
8 Service Mode > SORTER > ADJUST
SORTER> ADJUST
200RGT-2 Adj 200sheet stck tail right angle:trmmr
Lv.2 Details To adjust the cut angle on the tail side when the right angle is not
accurate at 3-direction cut for 200-sheet stack.
As the value is changed by 1, the rotation degree is changed by
0.1 mm.
+: rotation degree is increased, cut angle gets smaller
-: rotation decree is decreased, cut angle gets larger
Use case When the right angle is not accurate after the stack is cut
Display/adj/set range -100 to 100
Unit 0.1 mm
Default value 0
200RGT-3 Adj 200sheet stck fore right angle:trmmr
Lv.2 Details To adjust the cut angle on the fore edge side when the right angle is
not accurate at 3-direction cut for 200-sheet stack.
As the value is changed by 1, the rotation degree is changed by
0.1 mm.
+: rotation degree is increased, cut angle gets smaller
-: rotation decree is decreased, cut angle gets larger
Use case When the right angle is not accurate after the stack is cut
Display/adj/set range -100 to 100
Unit 0.1 mm
Default value 0
SLD-MTR Adj of slide motor HP: trimmer
Lv.2 Details To adjust the home position of the slide motor
If the home position of the slide motor is displaced, cut position or
finish size is also displaced.
As the value is changed by 1, the home position is changed by
0.1 mm (finish size is also changed).
+: decrease
-: increase
Use case When the cut position or finish size is displaced
Display/adj/set range -20 to 20
Unit 0.1 mm
Default value 0
STK-VR0 Stack volume 0mm adj value: trimmer
Lv.1 Details To enter the 0 mm adjustment value of stack volume attached to the
main grip.
Use case When the master controller PCB/EEPROM is replaced
Display/adj/set range 0 to 1023
Default value 0
STK-VR25 Stack volume 25mm adj value: trimmer
Lv.1 Details To enter the 25 mm adjustment value of stack volume attached to
the main grip.
Use case When the master controller PCB/EEPROM is replaced
Display/adj/set range 0 to 1023
Default value 0
8-429
8-429