Juniper JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010 Configuration Manual page 756

JUNOSe 11.1.x Link Layer Configuration Guide
setting
the local entity into loopback mode.............247
slow protocols
destination address of OAM PDUs and........230
specifying
action on exceeding high threshold, disabling
interface...................................................246
action on exceeding high threshold,
failover.....................................................246
detection of remote failure conditions.........246
high threshold for frame error events..........244
high threshold for frame seconds summary
error events.............................................244
high threshold for symbol error events........244
interface type..............................................242
link events to monitor.................................244
low threshold for frame error events...........244
low threshold for frame seconds summary
error events.............................................244
low threshold for symbol error events.........244
mode of discovery.......................................242
PDU loss threshold before link-fault event is
generated.................................................243
rate of transmission of Information OAM
PDUs........................................................243
remote loopback functionality.....................247
tracking of error frame events.....................244
tracking of error frame second events.........244
tracking of symbol error events...................244
window for frame error events....................244
window for frame seconds summary error
events......................................................244
window for symbol error events..................244
support for unified ISSU......................................242
support on SRP Ethernet interfaces.....................242
supported standards...........................................230
viewing
configurations for all interfaces on which
OAM is enabled........................................258
details about processing of packets,
statistics...................................................253
discovery mode...........................................250
general OAM parameters configured on an
interface...................................................255
link monitoring configured on an
interface...................................................255
warning message
while placing local entity in remote loopback
mode.......................................................247
Ethernet OAM link-fault management commands
ethernet oam lfm................................................243
ethernet oam lfm high-threshold.........................246
ethernet oam lfm link-monitor
frame-seconds.................................................244
ethernet oam lfm link-monitor
frame-seconds-summary.................................245
724
Index
ethernet oam lfm link-monitor
symbol-period.................................................245
ethernet oam lfm mode......................................243
ethernet oam lfm pdu-lost-threshold...................243
ethernet oam lfm pdu-transmit-interval..............243
ethernet oam lfm remote-failure.........................246
ethernet oam lfm remote-loopback start.............247
ethernet oam lfm remote-loopback stop.............248
ethernet oam lfm remote-loopback
supported........................................................247
show ethernet oam lfm discovery.......................250
show ethernet oam lfm statistics........................253
show ethernet oam lfm status.............................255
show ethernet oam lfm summary.......................258
Ethernet OAM messages See OAM messages
Ethertype value, assigning to
S-VLANs..........................183, 186, 459, 546, 589, 675
Event notification OAM PDUs
description of......................................................231
generating to the remote peer............................239
generation of and sending to the remote peer
when low threshold is exceeded..................237
identification of duplicate events
using sequence number...............................237
link monitoring function and..............................236
receive link path monitoring
and transmission to the remote peer...........238
responding to received notices...........................239
supported TLVs for tracking link faults
Errored Frame Event...................................237
Errored Frame Seconds Summary
Event.......................................................237
Errored Symbol Period Event .....................237
transmission of, multiple times
owing to failure in delivery..........................237
viewing...............................................................253
example.............................................................209, 210
examples, configuration
ATM 1483 subinterfaces, dynamic......................637
ATM VC classes...............................................59, 67
bridged Ethernet, dynamic.................................557
bridged Ethernet, static.......................................447
Cisco HDLC.........................................................508
IPoA, dynamic....................................................553
MLFR..................................................................138
MLPPP, dynamic.................................................328
MLPPP, static..............................................312, 328
Multiclass MLPPP, dynamic................................356
Multiclass MLPPP, static......................................357
PPPoE, dynamic.........................................528, 534
PPPoE, static...............................................386, 393
profiles for dynamic interfaces...........................593
transparent bridging...........................................488
VLAN subinterfaces, dynamic.....................667, 669
exporting ATM 1483 subinterface descriptions............45
Extensible Authentication Protocol. See EAP