Suzuki XL7 2007 Service Manual page 817

Calc. TWC Temp. Bank 1 or Bank 2: This parameter
displays the catalytic converter temperature as
calculated by the control module.
Catalytic Converter Protection Active: This
parameter displays if the control module is
commanding catalytic converter protection.
Catalyst Monitor Complete This Ignition: This
parameter displays the monitor completion status
during the current driving/monitoring cycle.
Catalyst Monitor Enabled This Ignition: This
parameter displays the monitor enable status during
the current driving/monitoring cycle.
CKP Resync Counter: This parameter displays the
number of times the control module re-syncs with the
CKP sensor.
Clutch Start Switch (If Equipped): This parameter
displays the state of the clutch pedal as determined
by the control module from the clutch start switch.
CMP Sensor: This parameter displays the speed of the
engine as calculated by the control module using the
signal from the CMP sensor. The scan tool will
display a higher value as engine speed is increased.
The scan tool will display a lower value as the engine
speed is decreased.
Cold Start up: This parameter displays the state of the
engine coolant temperature at start up.
CPP Switch (If Equipped): This parameter displays
the state of the clutch pedal as determined by the
control module from the clutch pedal switch.
Crank Request Signal: This parameter displays
whether the ignition switch has been cycled to the
crank position requesting the control module to
activate the starter relay.
Cruise Control Active: This parameter displays the
status of the cruise control system as determined by
the control module.
Cruise Disengage 1-8 History: The parameter
displays the last 8 cruise control disengages in order
from 1 to 8, with 8 being the most recent. There are
about 33 possible causes for the cruise control to
disengage.
Cruise Inhibited: This parameter displays the status of
the cruise control system as determined by the
control module.
Cruise On/Off Switch: This parameter displays the
status of the cruise control system as determined by
the control module.
Cruise Resume/Accel. Switch: This parameter
displays the status of the cruise control system as
determined by the control module.
Cruise Set/Coast Switch: This parameter displays the
status of the cruise control system as determined by
the control module.
Cylinder 1-6 IC Circuit Status: This parameter
displays the diagnostic state of the output driver for
the ignition control circuits. The scan tool will display
OK if the circuit is operating correctly. The scan tool
will display Short or Open if there is an open, short to
ground or a short to voltage on the circuit.
Cylinder 1-6 Injector Circuit Status: This parameter
displays the state of the fuel injector control circuit.
The parameter displays Fault if the fuel injector
control circuit is open, shorted to ground, or shorted
to voltage.
Cylinder 1-6 Knock Retard: This parameter displays
the knock retard as commanded by the control
module for cylinders 1-6. Each cylinder is controlled
individually based on both knock sensor signal
inputs.
Decel. Fuel Cutoff: This parameter displays the status
of the operating mode of the control module used to
turn off the fuel injectors and the EVAP canister
purge valve during certain deceleration conditions.
Desired Exh. CMP Bank 1 or 2: This parameter
displays the desired exhaust camshaft angle as
commanded by the control module.
Desired HO2S Bank 1 or 2 Sensor 1: This parameter
displays the voltage output from the HO2S to the
control module. A lower voltage indicates a lean
exhaust, while a higher voltage indicates a rich
exhaust.
Desired Idle Speed: This parameter displays the
desired engine idle speed as commanded by the
control module.
Desired Int. CMP Bank 1 or 2: This parameter
displays the desired intake camshaft angle as
commanded by the control module.
Distance Since DTC Cleared: This parameter displays
the distance accumulated since an emission
diagnostic trouble code was cleared. The scan tool
will display increasing distance as the vehicle is
driven.
DTC Set This Ignition: This parameter displays Yes if
a DTC set on the current ignition cycle.
EC Ignition Relay Command: This parameter displays
the state of the control circuit for control module
power relay as commanded by the control module.
EC Ignition Relay Circuit Status: This parameter
displays the state of the EC Ignition Relay control
circuit. The parameter displays Fault if the EC
Ignition Relay control circuit is open, shorted to
ground, or shorted to voltage. The parameter
displays Indeterminate until the circuit has been
commanded ON.
EC Ignition Relay Feedback Signal: This parameter
displays the voltage available at the EC ignition relay
pin of the control module.
ECM in VTD Fail Enable: This parameter indicates
whether or not the engine control module (ECM) is in
failure enable mode for the vehicle theft deterrent
(VTD) system.
ECT Sensor: This parameter displays the temperature
of the engine coolant based on input to the control
module from the engine coolant temperature (ECT)
sensor.
Engine Load: This parameter displays the calculated
engine load in percent based on inputs to the control
module from various engine sensors.
Fuel System: 1G-17