Suzuki 2009 Grand Vitara Owner's Manual
  1. Manuals
  2. Brands
  3. Suzuki Manuals
  4. Automobile
  5. 2009 Grand Vitara
  6. Owner's manual

Suzuki 2009 Grand Vitara Owner's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

ENGLISH
SERVICE STATION INFORMATION
Fuel recommendation:
See page 1-1
Engine oil recommendation:
Engine oil with "Starburst" symbol
For further details, see "Engine Oil and Filter" in the
"INSPECTION AND MAINTENANCE" section.
Suzuki Red: Magenta 100%, Yellow 100%
Suzuki Blue: Cyan 100%, Magenta 70%
takumi color: Cyan 100%, Black 85%
Black
13.5 mm
Brake and clutch fluid:
DOT3
Automatic transmission fluid:
SUZUKI ATF 3317 or Mobil ATF 3309
Tire cold pressure:
See the "Tire Information Label" located on the
driver's door lock pillar.

Advertisement

Table of Contents
loading

Related Manuals for Suzuki 2009 Grand Vitara

Summary of Contents for Suzuki 2009 Grand Vitara

  • Page 1 DOT3 Engine oil recommendation: Automatic transmission fluid: Engine oil with “Starburst” symbol SUZUKI ATF 3317 or Mobil ATF 3309 For further details, see “Engine Oil and Filter” in the Tire cold pressure: “INSPECTION AND MAINTENANCE” section. See the “Tire Information Label” located on the driver’s door lock pillar.
  • Page 2 This owner’s manual applies to the GRAND VITARA series: 79K035 NOTE: The illustrated model is one of the GRAND VITARA series. © COPYRIGHT SUZUKI MOTOR CORPORATION 2008 79K20-03E...
  • Page 3 IF YOU HAVE ANY PROBLEMS WITH YOUR SUZUKI: Please review the New Vehicle Warranty Information booklet supplied with your SUZUKI. Should you have a question or problem regarding the warranty or service of your vehicle, please take the following action:...
  • Page 4 Indicates a potential hazard that ling in either the United States or Canada, could result in death or injury. you may wish to contact the Suzuki Cus- tomer Relations Department directly of the country in which you are temporarily oper- ating your vehicle.
  • Page 5 CB (Citizen’s Band) radios may cause electronic interfer- ence with your vehicle’s ignition sys- tem, resulting in vehicle performance problems. Consult your SUZUKI dealer or qualified service technician for advice on installing such mobile communication equipment. 79K20-03E...
  • Page 6 MEMO 79K20-03E...
  • Page 7 INTRODUCTION Thank you for choosing SUZUKI and welcome to our growing family. Your choice was a wise one; SUZUKI products are a great value that will give you years of driving pleasure. This Owner’s Manual was prepared to help you have a safe, enjoyable, and trouble-free experience with your SUZUKI. In it you will learn about the vehicle’s operation, its safety features and maintenance requirements.
  • Page 8 SERVICE STATION GUIDE 1. Fuel (see section 1) 2. Engine hood (see section 5) 3. Tire changing tools (see section 8) 4. Engine oil dipstick <Yellow> (see section 7) 5. Automatic transmission fluid dipstick <Red> (see section 7) 6. Engine coolant (see section 7) 7.

  • Page 9: Table Of Contents

    TABLE OF CONTENTS FUEL RECOMMENDATION California Proposition 65 Warning BEFORE DRIVING WARNING OPERATING YOUR VEHICLE Engine exhaust, some of its constitu- ents, and certain product compo- DRIVING TIPS nents contain or emit chemicals known to the State of California to cause cancer and birth defects or OTHER CONTROLS AND EQUIPMENT other reproductive harm.
  • Page 10 ILLUSTRATED TABLE OF CONTENTS EXTERIOR EXAMPLE 1. Rear Window Wiper (P.2-79) 2. Engine Hood (P.5-37) 3. Windshield Wiper (P.2-77) 4. Roof Rails or Roof Rack Anchors (if equipped) (P.5-52) 5. Radio Antenna (P.5-8) 6. Spare Wheel (P.8-3) 7. Tailgate (P.2-3) 8.
  • Page 11 INTERIOR EXAMPLE 1. Interior Light (P.5-38, P.7-40) 2. Seat Belts (P.2-26) 3. Coat hooks (if equipped) (P.5-45) 4. Side Curtain Air Bags (P.2-46) 5. Sun Visor (P.5-38) 6. Overhead Console Box (if equipped) (P.5-45) 7. Spot Light (P.5-40, P.7-41) 8. Inside Rearview Mirror (P.2-17) 9.
  • Page 12 ILLUSTRATED TABLE OF CONTENTS INSTRUMENT PANEL EXAMPLE 1. Power Window Controls (if equipped) (P.2-15) 2. Power Mirror Control (if equipped) (P.2-18) 3. Remote Audio Controls (if equipped) (P.5-30) 4. Front Air Bags (P.2-45) 5. Cruise Control (P.3-26) 6. Hazard Warning Switch (P.2-77) 7.
  • Page 13 INSTRUMENT PANEL EXAMPLE 1. Lighting Control Lever (P.2-73)/ Turn Signal Control Lever (P.2-76) 2. Instrument Cluster (P.2-54) 3. Windshield Wiper and Washer Lever (P.2-77)/Rear Window Wiper and Washer Switch (P.2-79) 4. Rear Window Defroster and Outside Rearview Mirrors Defroster Switch (if equipped) (P.2-80) 5.
  • Page 14 Do not remove the messages for any reason. If a label comes off or the messages become difficult to be read, have it corrected by your SUZUKI dealer. 1. Air bag warning labels (on both sun visors) 2. Rollover warning label 3.

  • Page 15: Fuel Recommendation

    FUEL RECOMMENDATION FUEL RECOMMENDATION Fuel Recommendation ... 1-1 65D394 79K20-03E...

  • Page 16: Fuel Recommendation

    (wood alcohol) may be suitable for use in NOTE: your vehicle if they contain cosolvents and To help clean the air, SUZUKI recom- corrosion inhibitors. Do NOT USE fuels mends you use the oxygenated fuels. containing more than 5% methanol under However, if you are not satisfied with the any circumstances.

  • Page 17: Before Driving

    BEFORE DRIVING BEFORE DRIVING Keys ... 2-1 Door Locks ... 2-1 Keyless Start System Remote Controller/Keyless Entry System Transmitter ... 2-4 Theft Deterrent Light ... 2-15 Windows ... 2-15 Mirrors ... 2-17 Front Seats ... 2-18 Rear Seats ... 2-22 Seat Belts and Child Restraint Systems ...

  • Page 18: Keys: 8

    Keys: 8 Spare Tire Nut Lock: 5 BEFORE DRIVING Keys EXAMPLE 54G489 Your vehicle comes with a pair of identical keys. Keep the spare key in a safe place. One key can open all of the locks on the vehicle. The key identification number is stamped on a metal tag provided with the keys.
  • Page 19 Door Locks: 3, 5, 8 To unlock a front door from outside the vehicle, insert the key and turn the top of the key toward the rear of the vehicle. UNLOCK LOCK 64J002 To lock a door from inside the vehicle, turn the lock knob forward.
  • Page 20 Door Locks: 3, 5, 8 BEFORE DRIVING (when using the power door locking switch) To lock or unlock all the doors simulta- neously, depress the front or rear of the switch respectively. NOTE: • If your vehicle is equipped with the key- less entry system, you can also lock or unlock all doors by operating the remote controller/transmitter.

  • Page 21: Keyless Start System Remote Controller/Keyless Entry System Transmitter

    The transmitter has only a keyless After using the emergency lever, be sure to entry system. For details, refer to the fol- see your SUZUKI dealer. lowing explanations. BEFORE DRIVING Type A...
  • Page 22 • If you lose one of the remote controllers, • The turn signal lights will flash twice. ask your SUZUKI dealer as soon as pos- • If the interior light switch is in the sible for a replacement. Be sure to have “DOOR”...
  • Page 23 Door Locks: 3, 5, 8 “PANIC” button (3) function This function is to get the attention of oth- ers. Press the “PANIC” button (3) for more than 1 second. The headlights and taillights will blink for about 30 seconds. Also, the horn will sound intermittently for about 30 sec- onds at the same time.
  • Page 24 • If you lose one of the remote controllers, television. ask your SUZUKI dealer as soon as pos- sible for a replacement. Be sure to have your dealer program the new remote controller code in your vehicle’s memory...
  • Page 25 Door Locks: 3, 5, 8 • You can use up to four remote controllers and ignition keys for your vehicle. Ask your SUZUKI dealer for details. • The battery life of the remote controller is about two years, but it can vary depending on usage conditions.
  • Page 26 Door Locks: 3, 5, 8 BEFORE DRIVING Replacement of the battery If the remote controller becomes unreli- able, replace the battery. To replace the battery of the remote con- troller: 66J016 1) Insert a flat blade screw driver covered with a soft cloth in the slot of the remote controller and pry it open.
  • Page 27 • To purchase new remote controllers, see your SUZUKI dealer. • Before you begin programming, have all of your remote controllers available. To program a new remote controller 7.
  • Page 28 If you still cannot operate the systems, see your SUZUKI dealer. To change the old remote controller codes in your vehicle’s memory If you have lost one of the remote control- lers, you should change the remote con- troller codes in your vehicle’s memory as...
  • Page 29 • If you lose one of the transmitters, ask your SUZUKI dealer as soon as possible for a replacement. Be sure to have your dealer program the new transmitter code in your vehicle’s memory so that the old...
  • Page 30 5) Turn the ignition switch to the “LOCK” • To purchase new transmitters, see your position and remove the key within 10 SUZUKI dealer. seconds. All doors will lock/unlock to • Before you begin programming, have all confirm that this procedure has been of your transmitters available.
  • Page 31 Windows: 3, 8 52D212 6) Press the “UNLOCK” button (2) on the transmitter one time within 20 seconds (after step 5). All the doors will lock/ unlock to confirm that the procedure has been completed and the transmitter has been programmed. 7) If you want to program an additional transmitter, repeat the procedure from step 1) through step 6).

  • Page 32: Theft Deterrent Light

    Windows: 3, 8 Mirrors: 3, 8 BEFORE DRIVING Theft Deterrent Light EXAMPLE 78K013 This light will blink with the ignition switch in the “OFF” or “ACC” position. The blink- ing light is intended to deter theft by lead- ing others to believe that the vehicle is equipped with a security system.

  • Page 33: Mirrors

    Mirrors: 3, 8 CLOSE OPEN 81A009 To open a window, push the top part of the switch and to close the window lift up the top part of the switch. The driver’s window has an “auto-down” feature for added convenience (at toll booths or drive-through restaurants, for example).
  • Page 34 Seat Adjustment: 14 BEFORE DRIVING Mirrors Inside Rearview Mirror Day driving Night driving 78K033 You can adjust the inside rearview mirror by hand so as to see the rear of your vehi- cle in the mirror. To adjust the mirror, set the selector tab (1) to the day position, then move the mirror up, down or sideways by hand to obtain the best view.

  • Page 35: Front Seats

    Seat Adjustment: 14 Head Restraints: 3 Power Mirror Control (if equipped) 64J015 The switch to control the power rearview mirrors is located on the driver’s door panel. You can adjust the mirrors when the ignition switch is in the “ACC” or “ON” posi- tion.

  • Page 36: Seat Belts And Child Restraint Systems: 14

    Head Restraints: 3 Seat Belts and Child Restraint Systems: 14 BEFORE DRIVING Adjusting Seat Position 64J016 The adjustment lever for each front seat is located under the front of the seat. To adjust the seat position, pull up on the adjustment lever and slide the seat forward or rearward.
  • Page 37 Seat Belts and Child Restraint Systems: 14 Head Restraints 63J256 Head restraints are designed to help reduce the risk of neck injuries in case of an accident. Adjust the head restraint to the position which places the center of the head restraint closest to the top of your ears.
  • Page 38 Seat Belts and Child Restraint Systems: 14 BEFORE DRIVING 79K036 To reinstall the head restraint, insert the head restraint bars into the holes (4) and push the head restraint down. 2-21 Front Seat Heater (if equipped) EXAMPLE 78K018 With the ignition switch in the “ON” posi- tion, push in one or both of the seat heater Improperly using the seat heater can switches to warm the corresponding...
  • Page 39 Seat Belts and Child Restraint Systems: 14 CAUTION To avoid damaging the heater ele- ment: • Do not subject the front seats to heavy impacts, such as children jumping on them. • Do not cover the seat with any insulating materials such as blan- kets or cushions.
  • Page 40 Seat Belts and Child Restraint Systems: 14 BEFORE DRIVING Head Restraints Head restraints are designed to help reduce the risk of neck injuries in case of an accident. Adjust the head restraint to the position which places the center of the head restraint closest to the top of your ears.
  • Page 41 Seat Belts and Child Restraint Systems: 14 Folding Rear Seats The rear seat(s) of your vehicle can be folded forward to provide additional cargo space. To fold the rear seats forward: 1) Remove the luggage compartment cover. 66J211 2) Stow the seat belt buckles of the center and left seating position into the pocket of the seat cushion as shown in the illustration.
  • Page 42 Seat Belts and Child Restraint Systems: 14 BEFORE DRIVING 64J089 6) Fold the entire seat forward. 66J195 7) Push down the adjuster (2) to make the strap slack, and then unhook the strap by pushing down the hook (3). 2-25 Luggage or other cargo should be stowed in the luggage compartment with the rear seat in an upright posi-...
  • Page 43 Seat Belts and Child Restraint Systems: 14 64J091 2) Pull down the seat cushion until it locks into place. WARNING When returning the rear seat cushion to the normal position, be careful that your finger is not caught between the lock and the floor.
  • Page 44 Seat Belts and Child Restraint Systems: 14 BEFORE DRIVING Above the pelvis 65D606 WARNING • Never allow persons to ride in the cargo area of a vehicle. In the event of an accident, there is a much greater risk of injury for persons who are not riding in a seat with their seat belt securely fastened.
  • Page 45 Seat Belts and Child Restraint Systems: 14 WARNING (Continued) • Do not wear your seat belt over hard or breakable objects in your pockets or on your clothing. If an accident occurs, objects such as glasses, pens, etc. under the seat belt can cause injury.
  • Page 46 Seat Belts and Child Restraint Systems: 14 BEFORE DRIVING Safety reminder Sit up straight and fully back Low on hips 60A038 Low on hips 60A040 To reduce the risk of sliding under the belt during a collision, position the lap portion of the belt across your lap as low on your hips as possible and adjust it to a snug fit 2-29...
  • Page 47 Seat Belts and Child Restraint Systems: 14 52D249 NOTE: The word “CENTER” is molded into the buckle for the rear seat center belt. The buckles are designed so a latch plate can not be inserted into the wrong buckle. Seat Belt Reminder Driver’s seat belt reminder light 60A039 To unfasten the belt, push the red...
  • Page 48 Seat Belts and Child Restraint Systems: 14 BEFORE DRIVING reminder light in the instrument cluster and the front passenger’s seat belt reminder light in the center of the instrument panel will come on and a buzzer will sound as a reminder to the driver and front passenger to buckle their seat belts.
  • Page 49 Seat Belts and Child Restraint Systems: 14 Driver’s seat belt reminder If the driver’s seat belt remains unbuckled with the ignition key in the “ON” position, the driver’s seat belt reminder works as fol- lows: 1) The driver’s seat belt reminder light will come on for about 20 seconds when the ignition key is turned to the “ON”...
  • Page 50 Seat Belts and Child Restraint Systems: 14 BEFORE DRIVING Seat Belt Inspection EXAMPLE 65D209 Periodically inspect the seat belts to make sure they work properly and are not dam- aged. Check the webbing, buckles, latch plates, retractors, anchorages and guide loops.
  • Page 51 Infant restraint - rear seat only 65D584 Booster seat EXAMPLE 65D203 SUZUKI highly recommends that you use a child restraint system to restrain infants and small children. Many different types of Children could be endangered in a child restraint systems are available; make...
  • Page 52 Seat Belts and Child Restraint Systems: 14 BEFORE DRIVING 65D607 WARNING Do not install a rear-facing child restraint in the front passenger’s seat. If the passenger’s air bag inflates, a child in a rear-facing child restraint could be seriously injured. The back of a rear-facing child restraint would be too close to the inflating air bag.

  • Page 53: Supplemental Restraint System (Air Bags)

    Seat Belts and Child Restraint Systems: 14 Supplemental Restraint System (air bags): 3, 9, 12 CAUTION Before installing a child restraint sys- tem in the rear seat, raise the head restraint to the most upper position. ELR type belt EXAMPLE 65D233 Install your child restraint system accord- ing to the instructions provided by the child...
  • Page 54 Supplemental Restraint System (air bags): 3, 9, 12 BEFORE DRIVING A-ELR type EXAMPLE 83E032 2) Allow the extra webbing to retract, and pull the webbing toward the retractor to take up any slack. Make sure that the lap portion of the belt is tight around the child restraint system and the shoulder portion of the belt is positioned so that it can not interfere with the child’s head or...
  • Page 55 Supplemental Restraint System (air bags): 3, 9, 12 To revert from ALR to ELR EXAMPLE 65D267 When you unbuckle the seat belt and allow it to retract to a certain length, the retractor will automatically revert back to the normal ELR mode.
  • Page 56 Supplemental Restraint System (air bags): 3, 9, 12 BEFORE DRIVING EXAMPLE 65D340 3) Snap the strap hooks to the anchors. Take care not to pinch your fingers. EXAMPLE 65D341 4) Return the seatback to the normal, upright position. Tighten the lower straps as described in the child restraint 2-39 owner’s manual.
  • Page 57 Supplemental Restraint System (air bags): 3, 9, 12 EXAMPLE 54G184 4) Push the child restraint toward the anchors so that the connecting bar tips are partially hooked to the anchors. Use your hands to confirm the position. Installation-Child Restraint with Top EXAMPLE Strap Rear seat...
  • Page 58 If a seat belt cannot be fastened securely because it is not long enough, see your authorized SUZUKI dealer for a seat belt extender. Seat belt extenders are available for each seating position except for the rear center position.
  • Page 59 Upon activation, some noise will occur and some smoke may be released. This section of the owner’s manual These conditions are not harmful and do describes your SUZUKI’s SEAT BELT not indicate a fire in the vehicle. PRETENSIONER SYSTEM.
  • Page 60 “LOCK” position for at least 90 seconds before performing any electri- EXAMPLE cal service work on your SUZUKI. Do not touch pretensioner system components or wiring. The wires are wrapped with yellow tape or yellow tubing, and the couplers are yellow.
  • Page 61 Supplemental Restraint System (air bags): 3, 9, 12 Your vehicle is equipped with a Supple- mental Restraint System consisting of the following components in addition to a lap- shoulder belt at each front seating position. 1. Driver’s front air bag 2.
  • Page 62 “AIR BAG” light stays on, or comes on while driving, the air bag system (or the seat belt pretensioner system) may not work properly. Have the air bag system inspected by an authorized SUZUKI dealer as soon as possible. 2-45 Front Air Bags dashboard.
  • Page 63 Front air bags will not inflate Front air bags are not designed to inflate in rear impacts, side impacts, rollovers or minor frontal collisions, since they would offer no protection in those types of acci- dents. Remember, since air bags deploy only one time during an accident, seat belts are needed to restrain occupants from further movements during the acci-...
  • Page 64 BEFORE DRIVING side air bag cover to identify the location of Side collision range the side air bags. Side air bags are designed to inflate only in 64J034 severe side impact collisions. Side curtain air bags are located in the roof Side curtain air bags are designed to lining.
  • Page 65 Side air bags and side curtain air bags will probably not inflate An air bag supplements, or adds to, the crash protection offered by seat belts. The driver and all passengers must be properly restrained by wear- ing seat belts at all times, whether or not air bags are mounted at their seating position, to minimize the risk of severe injury or death in the event...
  • Page 66 BEFORE DRIVING “PASS AIR BAG OFF” Indicator bag, depending on the front passenger’s seating posture and body build. The air bag should be turned off in the following situations: • There is no occupant in the front pas- senger seat. •...
  • Page 67 According to accident statistics, children are safer when properly restrained in rear seating positions than in front seating posi- tions. Whenever possible, SUZUKI recom- mends you install child restraints in the rear seat. The front passenger sensing system is designed to enable the front passenger’s...
  • Page 68 Have the system inspected by an authorized SUZUKI dealer as soon as possible. 2-51 How the System Works WARNING In a frontal collision, the crash sensors will detect rapid deceleration and send a signal to the controller.
  • Page 69 The air bag will neither hinder your view nor make it harder to exit the vehicle. Air bags must inflate quickly and forcefully in order to reduce the chance of serious or fatal injuries. However, an unavoidable consequence of the quick inflation is that the air bag may irritate bare skin, such as the facial area against a front air bag.
  • Page 70 SUZUKI dealer as soon as possible. objects could be propelled by the Special procedures are required for servic- air bag in the event of a crash.

  • Page 71: Instrument Cluster

    Instrument Cluster EXAMPLE 1. Speedometer 2. Tachometer 3. Fuel gauge 4. Temperature gauge 5. Information display 6. MODE/ILL knob 7. TRIP knob 8. Warning and indicator lights BEFORE DRIVING 79K018 2-54 79K20-03E...

  • Page 72: Warning And Indicator Lights

    BEFORE DRIVING Warning and Indicator Lights For details about the seat belt reminder, refer to “Seat Belts and Child Restraint Front Passenger’s Seat Belt Systems” in this section. Reminder Light It is absolutely essential that the driver and passengers wear their seat belts at all times.
  • Page 73 Have • If you have a flat tire, replace it with your vehicle inspected by an autho- the spare tire. Refer to “Jacking rized SUZUKI dealer. Even if the light Instructions” in the “EMERGENCY turns off after blinking, indicating SERVICE”...
  • Page 74 Because the disc brake system is self- If one of these happens, have the system adjusting, the fluid level will drop as the inspected by your SUZUKI dealer. If the ABS becomes inoperative, the brake sys- brake pads become worn.
  • Page 75 • When the transfer switch (if equipped) is the ESP systems (other than ABS). You turned to the “4L LOCK” position, the should have the system inspected by an authorized SUZUKI dealer. canceled automatically. The light will ® For details of the ESP systems, refer to come on and stay on.
  • Page 76 ® the ESP system. Have your vehicle be inspected by your SUZUKI dealer inspected by an authorized SUZUKI before you drive the vehicle again. dealer. For details of the hill descent control sys- tem, refer to “Hill descent control System”...
  • Page 77 WARNING or blinks when the engine is running, ser- vice to the emission control system is nec- essary. Bring the vehicle to your SUZUKI dealer to have the emission control system serviced right away and avoid hard accel- eration until the service is performed.
  • Page 78 BEFORE DRIVING NOTE: Open Door Warning Light If the fuel filler cap is not installed fully, the electrical system gets wet (such as by driv- ing through a deep puddle of water) or the fuel tank gets nearly empty, the malfunc- tion indicator lamp may come on.
  • Page 79 If this light blinks in red, it reminds you that Daytime Running Light (D.R.L.) the remote controller is not in the vehicle. Indicator Light (if equipped) For details, refer to “Keyless Start System Remote Controller/Keyless Entry System Transmitter” in this section. Turn Signal Indicators With the D.R.L.

  • Page 80: Speedometer

    EXAMPLE inspected by an authorized SUZUKI dealer. NOTE: The information display shows the warning and indicator message when the transfer system is operated, or has a problem. Master Warning Indicator Light The speedometer indicates vehicle speed in km/h and mph.

  • Page 81: Fuel Gauge

    Fuel Gauge NOTE: The information display shows the warning and indicator message when this light comes on. Avoid driving with an extremely low fuel level. Running out of fuel could cause the engine to misfire, damag- ing the catalytic converter. NOTE: The activation point of the low fuel warning light (1) varies depending on road condi-...

  • Page 82: Brightness Control

    BEFORE DRIVING Brightness Control EXAMPLE NOTE: • If you do not turn the brightness control knob within about 5 seconds of activat- ing the brightness control display, the brightness control display will be can- celed automatically. • When you reconnect the battery, the brightness of the instrument panel lights 79K039 will be reinitialized.
  • Page 83 The information display shows the follow- A/T Selector Position ing information. (for automatic transmission) Display (A) EXAMPLE A/T selector position indicator (for auto- matic transmission) Display (B) Warning and Indicator Messages/Fuel Consumption/Driving Range/Average Speed The display (A) shows the automatic trans- mission selector position.
  • Page 84 BEFORE DRIVING To switch the display indication, push the NOTE: MODE/ILL knob (2) quickly. When you reconnect the negative (–) ter- minal to the battery, the value of average NOTE: fuel consumption will be shown after driv- The value of fuel consumption, driving ing for a while.
  • Page 85 which includes average speed during pre- Odometer/Trip meter/Thermometer vious driving. When the ignition switch is turned to the “ON” position, the display (C) shows one of To reset the value of average speed, push the following three indications, trip meter A, and hold the MODE/ILL knob (2) for about trip meter B and thermometer.
  • Page 86 BEFORE DRIVING Thermometer Setting mode The thermometer indicates the outside temperature. EXAMPLE When the ignition switch is in the “ON” 79K067 position and the vehicle is stationary, you If the outside temperature nears freezing, can enter the setting mode of the informa- the message shown in the above illustra- tion display by pushing and holding the tion will appear on the display.
  • Page 87 Temperature units Warning and Indicator Messages You can change the units that temperature The display shows the warning and indica- is displayed in. tor messages to let you know about certain vehicle problems. NOTE: A tone may also sound to alert you. When you change the units that tempera- If warning and indicator messages appear ture is displayed in, the air conditioning...
  • Page 88 (#1) Close all doors completely. Ding There may be a problem with the ESP Have your vehicle inspected by an authorized SUZUKI dealer. Ding There may be problem with the hill descent control sys- tem and the hill hold control system.
  • Page 89 )” in the “OPERATING YOUR VEHICLE” section for details. Sound Cause and Remedy There may be a problem with the 4WD system. Have your vehicle inspected by an authorized SUZUKI dealer. Ding Fuel is low. (#1) Fill the fuel tank immediately.

  • Page 90: Lighting Control Lever

    BEFORE DRIVING Lighting Control Lever 65D611 WARNING To avoid possible injury, do not oper- ate controls by reaching through the steering wheel. 2-73 Your vehicle’s lighting system is controlled by three main systems: the Lighting switch, the Auto-On Headlight System (when the lighting switch is in the “AUTO”...
  • Page 91 The three systems work together to operate your lights as shown in the following chart: E/G: Engine IG: Ignition switch ON: Lights ON LIGHT: When it is light around the light sensor (5). DARK: When it is dark around the light sensor (5). IG OFF Lighting Main lights to...
  • Page 92 BEFORE DRIVING Auto-On Headlight System HIGH PASS 79K016 With the headlights on, push the lever for- ward to switch to the high beams or pull The Auto-on headlight system automati- the lever toward you to switch to the low cally turns on all lights that are operated by beams.

  • Page 93: Front Fog Light Switch (If Equipped)

    Daytime Running Light (D.R.L.) Front Fog Light Switch System (if equipped) The headlights light, but are dimmer than the low beam, when the following three conditions are all met. Also, the D.R.L. indi- cator light on the instrument panel comes Conditions for D.R.L.

  • Page 94: Hazard Warning Switch

    BEFORE DRIVING Turn Signal Operation Hazard Warning Switch With the ignition switch in the “ON” posi- tion, move the lever up or down to activate the right or left turn signals. Push in the hazard warning switch to acti- vate the hazard warning lights. All four turn signal lights and both turn signal indicators will flash simultaneously.
  • Page 95 Windshield Wipers EXAMPLE EXAMPLE MIST 63J301 If the lever is equipped with the “INT TIME” To turn the windshield wipers on, move the control, turn the control forward or rear- lever up and down to one of the four oper- ward to adjust the intermittent wiper opera- tion to the desired interval.
  • Page 96 BEFORE DRIVING Rear Window Wiper/Washer Switch CAUTION EXAMPLE To help prevent damage to wind- shield wiper and washer system components, you should take the fol- lowing precautions: • Do not continue to hold in the lever when there windshield washer fluid being sprayed or the washer motor can be damaged.

  • Page 97: Tilt Steering Lock Lever

    Tilt Steering Lock Lever Horn EXAMPLE UNLOCK LOCK EXAMPLE 64J037 The lock lever is located under the steering Press the horn pad on the steering wheel column. To adjust the steering wheel to sound the horn. The horn will sound with height: the ignition switch in any position.
  • Page 98 BEFORE DRIVING An indicator light will be lit when the defroster is on. The defroster will only work when the engine is running. To turn off the defroster, push the switch (1) again. CAUTION The rear window defroster and the outside rearview mirrors use a large amount of electricity.

  • Page 99: Operating Your Vehicle

    OPERATING YOUR VEHICLE OPERATING YOUR VEHICLE Exhaust Gas Warning ... 3-1 Daily Inspection Checklist ... 3-2 Ignition Switch ... 3-3 Parking Brake Lever ... 3-7 Pedals ... 3-8 Starting the Engine ... 3-9 Engine Block Heater (if equipped) ... 3-10 Using the Transmission ...

  • Page 100: Exhaust Gas Warning

    Exhaust Gas Warning: NO OPERATING YOUR VEHICLE Exhaust Gas Warning 52D334 WARNING Avoid breathing exhaust gases. Exhaust gases contain carbon mon- oxide, a potentially lethal gas that is colorless and odorless. Since carbon monoxide is difficult to detect by itself, be sure to take the following precautions to help prevent carbon monoxide from entering your vehicle.

  • Page 101: Daily Inspection Checklist

    Daily Inspection Checklist: NO Starting the Engine: 1 Daily Inspection Checklist Before Driving 60A187S 1) Make sure that windows, mirrors, lights and reflectors are clean and unob- structed. 2) Visually check the tires for the following points: – the depth of the tread groove –...

  • Page 102: Ignition Switch

    Starting the Engine: 1 OPERATING YOUR VEHICLE Ignition Switch 65D611 WARNING To avoid possible injury, do not oper- ate controls by reaching through the steering wheel. Vehicle Without Keyless Start Sys- Manual transmission EXAMPLE • Manual transmission vehicles 60B041 You must push in the key to turn it to the The ignition switch has the following four “LOCK”...
  • Page 103 Starting the Engine: 1 Engine Block Heater: 1 Accessories such as the radio can oper- ate, but the engine is off. This is the normal operating position. All electrical systems are on. START This is the position for starting the engine using the starter motor.
  • Page 104 Engine Block Heater: 1 Using the Transmission: 10 OPERATING YOUR VEHICLE of the remote controller may be unreli- able. NOTE: • If the battery of the remote controller runs down or there are strong radio waves or noise, the operating range may be narrower or the remote controller may be inoperative.
  • Page 105 If the engine does not start after several attempts, check the fuel and igni- tion SUZUKI dealer. • Do not leave the ignition switch in the “ON” position if the engine is not running or the battery will dis- charge.

  • Page 106: Parking Brake Lever

    • If the parking brake does not hold even though the transmission is in the vehicle securely or does not gear or in Park, you must set the fully release, have your vehicle parking brake fully. inspected immediately by an autho- rized SUZUKI dealer. WARNING 79K20-03E...

  • Page 107: Pedals

    Brake Pedal (2) Your SUZUKI vehicle is equipped with front and rear disc brakes. Depressing the brake pedal applies both sets of brakes. You may hear occasional brake squeal when you apply the brakes.

  • Page 108: Starting The Engine

    WARNING If you are unable to start the engine using Make sure that the parking brake is this procedure, consult your SUZUKI set fully and the transmission is in dealer. Neutral (or Park for vehicles with an...

  • Page 109: Engine Block Heater (If Equipped)

    Using the Transfer Switch: 10 Engine Block Heater (if equipped) EXAMPLE 79K040 The engine block heater will help you start the engine more easily in very cold weather (–18°C (0°F) or below). To use the engine block heater: 1) Turn off the engine. 2) Open the engine hood.

  • Page 110: Using The Transmission

    Using the Transfer Switch: 10 OPERATING YOUR VEHICLE Using the Transmission Manual Transmission 65D449 Starting off To start off, depress the clutch pedal all the way to the floor and shift into 1st gear. After releasing the parking brake, gradually release the clutch.
  • Page 111 Using the Transfer Switch: 10 Gearshift lever 66J004 The gearshift lever is designed that it can not be shifted out of the “P” position unless the ignition switch is in the “ON” position and the brake pedal is depressed. WARNING Always depress the brake pedal before shifting from “P”...
  • Page 112 Using the Transfer Switch: 10 OPERATING YOUR VEHICLE CAUTION Be sure to take the following precau- tions to help avoid damage to the automatic transmission: • Make sure that the vehicle is com- pletely stopped before shifting into “P” or “R”. •...
  • Page 113 Using the Transfer Switch: 10 Use the gearshift lever positions as described below: P (Park) Use this position to lock the transmission when the vehicle is parked or when start- ing the engine. Shift into Park only when the vehicle is completely stationary. WARNING If you have a 4-wheel drive vehicle, never leave the transfer switch in “N”...

  • Page 114: Using The Transfer Switch (If Equipped)

    Using the Transfer Switch: 10 OPERATING YOUR VEHICLE If You Can Not Shift Automatic Transmission Gearshift Lever Out of “P” (PARK) 78K043 Vehicles with an automatic transmission have an electrically operated park-lock fea- ture. If the vehicle’s battery is discharged, or there is some other electrical failure, the automatic transmission cannot be shifted out of Park in the normal way.
  • Page 115 Using the Transfer Switch: 10 Braking: 6 (11) (1) Front differential (2) Engine (3) Transmission (4) High/Low clutch (5) Transfer case (6) Center differential (7) Differential lock clutch (8) Chain (9) Rear propeller shaft (10) Rear differential (11) Front propeller shaft (10) 64J143 OPERATING YOUR VEHICLE...
  • Page 116 Braking: 6 OPERATING YOUR VEHICLE Description of Transfer Switch Positions N (Neutral) 3-17 In this position, engine power is not sup- plied to the front or rear axles. Only use this position for towing your vehicle. When you turn the transfer switch to the “N”...
  • Page 117 Braking: 6 OPERATING YOUR VEHICLE 4H (4-wheel drive high range) In this position, engine power is supplied to the front and rear axles. Use this position for normal driving. 64J220 3-18 79K20-03E...
  • Page 118 Tire Pressure Monitoring System (TPMS): OPERATING YOUR VEHICLE 4H LOCK (4-wheel drive high range center differential lock) 3-19 In this position, engine power is supplied to the front and rear axles and you get better traction than when driving in “4H”. Use this position when you need better traction than “4H”...
  • Page 119 Tire Pressure Monitoring System (TPMS): 4L LOCK (4-wheel drive low range center differential lock) OPERATING YOUR VEHICLE In this position, engine power is supplied to the front and rear axles and you get better traction and more low-speed torque than when driving in “4H”.
  • Page 120 Tire Pressure Monitoring System (TPMS): Break-In: 6 OPERATING YOUR VEHICLE Transfer Switch Operation Operate the transfer switch according to appropriate procedure described below: From N to 4H Stop the vehicle completely, place the transmission in “N” (Neutral) and depress the brake pedal and the clutch pedal fully (if equipped), then push in and turn the switch to shift into “4H”.
  • Page 121 Catalytic Converter: NO tion for 5 seconds until the “N” indicator blinks, then turn the switch to the “N” posi- tion. When you turn the transfer switch to the “N” position, “N” indicator will come on with the buzzer sound. CAUTION •...
  • Page 122 Catalytic Converter: NO Improving Fuel Economy: NO OPERATING YOUR VEHICLE The basic operation for transfer switch Current Position Current Indicator 4H LOCK 4L LOCK N: Neutral 4H: 4-wheel drive high range mode 4H LOCK: 4-wheel drive high range center differential lock mode 4L LOCK: 4-wheel drive low range center differential lock mode 3-23 Target Position...
  • Page 123 Cause and Remedy ing Indicator Blinks There may be a problem with the 4WD system. Have your vehicle inspected by an authorized SUZUKI dealer. 79K074 Blinks Series of This message informs you that the Beeps transfer switch is in “N”, which is used only for towing your vehicle.
  • Page 124 OPERATING YOUR VEHICLE Transfer Switch Warning and Indicator messages Operation Switching between “4H LOCK” and “4L LOCK” Switching between “4H” and “N” 3-25 Master Warn- Sound Cause and Remedy ing Indicator Beep (For automatic transmission) The desired transfer gear has not been engaged.

  • Page 125: Cruise Control

    Cruise Control When you push the “ON/OFF” switch, the system is on and a “CRUISE” indicator light on the instrument cluster will be on. 79K032 The cruise control system allows you to maintain a steady speed without keeping your foot on the accelerator pedal. The controls for operating the cruise control When the vehicle’s speed is controlled by system are on the steering wheel.

  • Page 126: Braking

    OPERATING YOUR VEHICLE To reset the cruise control to a faster To “Resume” a Previously Set speed, use either of the following proce- Speed dures: After canceling cruise control operation without turning off the “ON/OFF” switch • Hold in the “RES/ACC” switch (4). Vehi- (1), you can “resume”...
  • Page 127 WARNING If water gets into the brake drums, Even without reserve power in the brake performance may become poor brake system, you can still stop the unpredictable. After driving vehicle by pressing the brake pedal through water or washing the under- harder than normally required.
  • Page 128 If both warning fully. lights come on, drive carefully, avoid- ing hard braking as much as possi- and then start the engine again. ble, and ask your SUZUKI dealer to (Continued) inspect the ABS system immediately. WARNING WARNING...

  • Page 129: Electronic Stability Program (Esp®)

    How the ABS Works Electronic Stability Program A computer continuously monitors wheel (ESP speed. computer compares changes in wheel speed when braking. If the wheels slow suddenly, indicating a skidding situation, computer will change braking pressure several times The Electronic Stability Program (ESP each second to prevent the wheels from helps to control the vehicle during corner- locking.
  • Page 130 ESP tems (other than ABS). You should ® may not work properly if have the systems inspected by an authorized SUZUKI dealer. NOTE: When the SLIP indicator light comes on and stays on while driving, indicating a ®...
  • Page 131 ® activate the ESP systems: have the systems inspected by an 1) Drive your vehicle straight ahead with- authorized SUZUKI dealer. out tire slippage at a speed greater than approximately 15 km/h (9 mph) for a NOTE: few seconds When the “ESP” warning light comes on, 2) The slip indicator light will go out and ®...
  • Page 132 OPERATING YOUR VEHICLE (with hill descent control) canceled to provide improved vehicle traction, and the “ESP OFF” indicator light will come on. When the transfer switch (if equipped) is turned to the “4L LOCK” position, brake- traction control can be activated. Brake- traction control brakes the spinning wheel to distribute drive power to the other wheels for increased climbing abil-...
  • Page 133 Hill descent control System Hill descent control switch (if equipped) The hill descent control system is designed to reduce the driver’s workload when going down steep, rough and/or slippery hills where the vehicle cannot decelerate enough by engine braking alone. The hill descent control system helps to control vehicle speed by automatically engaging the vehicle’s brakes, as needed, so you...
  • Page 134 Hill descent control Indicator Light by an authorized SUZUKI dealer. 79K050 When the hill descent control system is If the message shown in the above illustra-...

  • Page 135: Tire Pressure Monitoring System (Tpms) (If Equipped)

    SUZUKI tire if you bring your vehicle to an autho- dealer. rized SUZUKI dealer to register the ID code of the spare tire sensor. Refer to NOTE: “Replacing Tires and/or Wheels” in this The hill hold control system will not acti- section.
  • Page 136 Have nation of the TPMS low tire pressure your vehicle inspected by an autho- telltale. rized SUZUKI dealer. Even if the light turns off after blinking, indicating that the monitoring system has recovered, make sure to have an authorized SUZUKI dealer check the system.
  • Page 137 on the tire information placard should WARNING cause the low tire pressure warning light to turn off. If the low tire pressure warning light If the light turns on again shortly after comes on and stays on, reduce your adjusting the pressure in your tires, you speed and avoid abrupt steering and may have a flat tire.
  • Page 138 • When you use non-genuine SUZUKI wheels or tires. Replacing Tires and/or Wheels If you get a flat tire, Suzuki recommends that you have an authorized SUZUKI dealer mount a new tire on the wheel that had the flat tire, and reinstall this tire on the...
  • Page 139 WARNING Only use tires and wheels recom- mended by SUZUKI as standard or optional equipment for your vehicle. Use of tires or wheels not recom- mended by SUZUKI can result in TPMS failure. Refer to “Tires” in the “INSPECTION AND MAINTENANCE”...
  • Page 140 OPERATING YOUR VEHICLE MEMO 3-41 79K20-03E...

  • Page 141: Driving Tips

    DRIVING TIPS DRIVING TIPS Important Vehicle Design Features To Know ... 4-1 Break-In ... 4-2 Catalytic Converter ... 4-2 Improving Fuel Economy ... 4-3 On-Pavement Driving ... 4-4 Off-Road Driving ... 4-6 60G409 79K20-03E...

  • Page 142: Important Vehicle Design Features To Know

    Multipurpose vehicles such as your new SUZUKI have higher ground clearance and a narrower track than conventional pas- In a rollover crash, an unbelted person is senger cars, to make them capable of per-...

  • Page 143: Break-In

    Important Vehicle Design Features To Know: NO On-Pavement Driving: NO Shorter Wheelbase Along with its higher ground clearance, your vehicle has a shorter wheelbase and shorter front and rear overhangs than many passenger cars. These features combine to allow you to drive your vehicle over hillcrests without hanging up on them or damaging the frame and chassis com- ponents.

  • Page 144: Improving Fuel Economy

    On-Pavement Driving: NO Off-Road Driving: NO DRIVING TIPS CAUTION To minimize the possibility of catalyst or other vehicle damage: • Maintain the engine in the proper operating condition. • In the event of an engine malfunc- tion, particularly involving engine misfire or other apparent loss of performance, have the vehi- cle serviced promptly.

  • Page 145: On-Pavement Driving

    Off-Road Driving: NO Keep the air cleaner clean EXAMPLE 60A183S A dirty air cleaner will cause the fuel injec- tion system to supply too much fuel to the engine for the amount of air being sup- plied. The result is waste of fuel due to incomplete fuel burning.
  • Page 146 Off-Road Driving: NO DRIVING TIPS Don’t Make Sharp Turns As mentioned before, small multipurpose vehicles have specific design characteris- tics that allow them to perform in a wide variety of applications. These characteris- tics also change the cornering behavior relative to conventional passenger cars. Remember, small multipurpose vehicles have more responsive steering and a higher center of gravity than conventional...

  • Page 147: Off-Road Driving

    Off-Road Driving Do Not Turn on or Drive Across the Side of Hills Your vehicle has specific design character- Turning on or driving across the side of a istics for off-road driving. When you leave hill can be extremely hazardous. Most of the pavement, you will encounter driving the vehicle’s weight will be transferred to surfaces of all kinds which may change...
  • Page 148 DRIVING TIPS Tire Chains WARNING Tire chains should only be used if they are needed to increase traction or are required • Do not allow anyone to stand near by law. Make sure that the chains you use the vehicle when you are rocking it, are small-link chains or cable-type chains and do not spin the wheels faster and are the correct size for your vehicle’s...
  • Page 149 • Do not use tires other than those effectiveness. specified by SUZUKI. Never use dif- • Do not use “4H LOCK” or “4L ferent sizes or types of tires on the LOCK” drive for normal driving.
  • Page 150 DRIVING TIPS MEMO 79K20-03E...

  • Page 151: Other Controls And Equipment

    OTHER CONTROLS AND EQUIPMENT OTHER CONTROLS AND EQUIPMENT Automatic Heating and Air Conditioning System (Climate Control) ... 5-1 Radio Antenna ... 5-8 Audio Systems ... 5-8 Fuel Filler Cap ... 5-36 Engine Hood ... 5-37 Sun Visor ... 5-38 Interior Light Switch ... 5-38 Luggage Compartment Light ...

  • Page 152: Automatic Heating And Air Conditioning System (Climate Control)

    Parking Brake Lever: 6 Pedals: 6 OTHER CONTROLS AND EQUIPMENT Automatic Heating and Air Conditioning System (Climate Control) Air Outlet EXAMPLE 1. Windshield defroster outlet 2. Side defroster outlet 3. Side outlet 4. Center outlet 5. Floor outlet Center outlet 66J250 EXAMPLE Open...
  • Page 153 Pedals: 6 Gearshift Lever: 10 Side outlet 63J045 When “Open”, air comes out from the side outlets regardless of the air flow selector position. OTHER CONTROLS AND EQUIPMENT Description of Controls (1) Temperature selector (2) Blower speed selector (3) Air intake selector (4) Air flow selector (5) Defrost switch (6) “OFF”...
  • Page 154 Gearshift Lever: 10 Fuel Filler Cap: 5 OTHER CONTROLS AND EQUIPMENT Temperature selector (1) 78K047 Turn the temperature selector (1) to adjust the temperature. Air conditioning switch (8) Blower speed selector (2) A/C: OFF A/C: ON 79K021 The air conditioning switch (8) is used to The blower speed selector (2) is used to turn on and off the air conditioning system.
  • Page 155 Fuel Filler Cap: 5 Folding Seats: 14 Air intake selector (3) 79K022 Push the air intake selector (3) to change between the following modes. If the “AUTO” switch (7) is pushed, the air intake will vary automatically as the climate control system maintains the selected tem- perature.
  • Page 156 Folding Seats: 14 OTHER CONTROLS AND EQUIPMENT Ventilation (c) 64J069 Temperature-controlled air comes out of the center and side air outlets. Bi-level (d) 64J070 Temperature-controlled air comes out of the floor outlets and cooler air comes out of the center and side outlets. When the temperature selector (1) is in the fully COLD position or fully HOT position, how- ever, the air from the floor outlets and the...
  • Page 157 You should have the system inspected by an autho- rized SUZUKI dealer. NOTE: • To find the temperature at which you are most comfortable, start with the 22°C (72°F) setting.
  • Page 158 Clean or replace them as specified in 64J074 “INSPECTION AND MAINTENANCE” sec- NOTE: tion. Have this job done by your SUZUKI If you need maximum defrosting: dealer as the lower glove box must be low- • push the defrost switch (5) to turn on the ered for this job.

  • Page 159: Radio Antenna

    Interior Light Switch: 7 Spot Light: 7 Radio Antenna 63J055 The radio antenna on the roof is remov- able. To remove the antenna, turn it coun- terclockwise. To reinstall the antenna, turn it clockwise firmly by hand. CAUTION avoid damage radio antenna: •...

  • Page 160: Luggage Compartment Light: 7

    Even in the event that trouble arises, never open the case, disassemble the unit, or lubricate the rotating parts. Please bring the unit to an authorized SUZUKI dealer or a Clarion service Department. Cautions on Handling Never touch the surface.
  • Page 161 Front Seat Heater: 8 52D348 Never stick labels on the surface of the compact disc or mark the surface with a pencil or pen. 52D349 Do not use any solvents such as commer- cially available cleaners, anti-static spray, or thinner to clean compact discs. OTHER CONTROLS AND EQUIPMENT NOTE: •...
  • Page 162 Assist Grips: 3 Coat Hooks: Sunroof: 5, 8 OTHER CONTROLS AND EQUIPMENT Basic Operations Type 1 AM/FM/XM CD PLAYER WITH CD CHANGER CONTROL Type 2 AM/FM/XM 6-CD PLAYER WITH CD CHANGER CONTROL 5-11 Display (1) Power on/off knob Volume control knob (2) Tone/balance/fader control knob (3) Preset button 5 (4) Preset button 6...
  • Page 163 Sunroof: 5, 8 Turning power on/off Press the power on/off knob (1). The unit starts in the function mode it was in when the power was turned off last. Adjusting the volume Turn the volume control knob (1). Turning it clockwise increases the volume; turning it counterclockwise decreases the volume.
  • Page 164 Sunroof: 5, 8 OTHER CONTROLS AND EQUIPMENT Listening to the Radio Type 1 AM/FM/XM CD PLAYER WITH CD CHANGER CONTROL Type 2 AM/FM/XM 6-CD PLAYER WITH CD CHANGER CONTROL 5-13 Display (1) Band switch button (FM/AM) (2) Seek up button (3) Seek down button (4) Manual tuning knob (5) Preset buttons (1 to 6)
  • Page 165 Engine Hood: 5 Selecting the reception band Press the band switch button (1). Each time the button is pressed, the recep- tion band is switched as follows: 66J098 Seek tuning Press the seek up button (2) or the seek down button (3). The unit stops searching for a station at a frequency where a broadcast station is available.

  • Page 166: Listening To A Cd

    Cup Holder and Storage Bin: 3, 14 OTHER CONTROLS AND EQUIPMENT Radio Reception Radio reception can be affected by envi- ronment, atmospheric conditions, or radio signal’s power and distance from the sta- tion. Nearby mountains and buildings may interfere or deflect radio reception, causing poor reception.
  • Page 167 Overhead Console Box: Accessory Socket: 8 Type 1 AM/FM/XM CD PLAYER WITH CD CHANGER CONTROL (Built in CD Player) OTHER CONTROLS AND EQUIPMENT Display (1) CD insertion slot (2) CD eject button (3) Disc button (CD/AUX) (4) Track up button/Fast forward button (5) Track down button/Rewind button (6) Repeat button (RPT) (A) Mode indicator...
  • Page 168 Accessory Socket: 8 Cigarette Lighter and Ashtray: 3, 8 OTHER CONTROLS AND EQUIPMENT Loading a CD Insert a CD in the CD insertion slot (1). When a CD is loaded, play starts and the CD indicator (A) lights. Ejecting a CD Press the CD eject button (2).
  • Page 169 Frame Hooks: 5, 6 Tire Changing Tools: 3, 5 Type 2 AM/FM/XM 6-CD PLAYER WITH CD CHANGER CONTROL (Built-in CD Changer) OTHER CONTROLS AND EQUIPMENT Display (1) Load button (LOAD) (2) Disc select buttons (1 to 6) (3) CD insertion slot (4) CD eject button (5) Disc button (CD/AUX) (6) Track up button/Fast forward button...
  • Page 170 Tire Changing Tools: 3, 5 Shopping Hook: Front Seat Back Pocket: 3 OTHER CONTROLS AND EQUIPMENT NOTE: About Single CDs (8 cm CDs) • Since the unit is not compatible with a single CD, do not load it into the unit. •...
  • Page 171 Underseat Tray: 3 Luggage Restraint Loops: 5 Ejecting all the CDs Press the CD eject button (4) for 2 seconds or longer. All the CDs will be ejected from the unit in a sequential manner. • Please prepare location where removed CDs can be stored.
  • Page 172 Luggage Compartment Cover: 5 OTHER CONTROLS AND EQUIPMENT Listening to an MP3/WMA Disc Type 1 AM/FM/XM CD PLAYER WITH CD CHANGER CONTROL Type 2 AM/FM/XM 6-CD PLAYER WITH CD CHANGER CONTROL 5-21 Display (Type 1) Display (Type 2) (1) Sound control knob (2) Repeat button (RPT) (3) Track up button/Fast forward button (4) Track down button/Rewind button...
  • Page 173 Underfloor Bins: Roof Rails or Roof Rack Anchors: 5, 13 What is MP3/WMA? MP3 (MPEG1/2 Audio Layer-III) and WMA (Windows MediaTM Audio) are the com- pression formats of digital audio. The former is developed by MPEG (Motion Pic- ture Experts Group), and the latter is developed by Microsoft Corporation.
  • Page 174 Roof Rails or Roof Rack Anchors: 5, 13 HomeLink: OTHER CONTROLS AND EQUIPMENT Compression formats • Bit rate MPEG1 Audio Layer III : 32 k - 320 kbps MPEG2 Audio Layer III : 8 k - 160 kbps • Sampling frequency MPEG1 Audio Layer III : 44.1 k/48 k/32 MPEG2 Audio Layer III : 22.05 k/24 k/16 WMA (Ver.7, Ver.8, Ver.
  • Page 175 HomeLink: NOTE: This operation should be performed within 2 seconds. To cancel repeat play, press the repeat but- ton (2) several times to change the repeat play mode to OFF. • TRACK REPEAT The indication “TRACK RPT” appears in the display for 2 seconds and then the repeat indicator (D) lights.

  • Page 176: Listening To A Xm Satellite Radio (Option)

    (A) Band (B) Channel number (C) Category indicator If you want to purchase XM Satellite Radio Service, contact your SUZUKI dealer. It is necessary to buy a special tuner to receive XM broadcasting. Your vehicle is capable of receiving XM...
  • Page 177 XM MODE Selecting a category Press the seek up button (3) or seek down Selecting a band button (4) to select a category. Press the XM button (1). Each time the button is pressed, the band Displaying the category changes in the following order. Press the category button (2) to have the currently selected category appear on the display.

  • Page 178: Listening To Audio For Aux (Option)

    OTHER CONTROLS AND EQUIPMENT Listening to Audio for AUX (Option) Type 1 AM/FM/XM CD PLAYER WITH CD CHANGER CONTROL Type 2 AM/FM/XM 6-CD PLAYER WITH CD CHANGER CONTROL 5-27 Display 66J221 (1) Aux button (CD/AUX) (A) Mode indicator Aux function This system has an external input terminal so you can listen to audio from an external device connected to this unit.
  • Page 179 Listening to a CD from an External CD Changer (Option) Type 1 AM/FM/XM CD PLAYER WITH CD CHANGER CONTROL Type 2 AM/FM/XM 6-CD PLAYER WITH CD CHANGER CONTROL OTHER CONTROLS AND EQUIPMENT Display (A) (B) (1) Disc button (CD/AUX) (2) Disc select buttons (1 to 6) (3) Track up button/Fast forward button (4) Track down button/Rewind button (5) Repeat button (RPT)
  • Page 180 OTHER CONTROLS AND EQUIPMENT Selecting a CD changer mode Selecting a track Press the disc button (1). • Press the track up button (3) to listen to Each time the button is pressed, the the next track. selected CD plays as follows: •...

  • Page 181: Remote Audio Controls

    • TRACK REPEAT Remote Audio Controls The indication “TRACK RPT” appears in (if equipped) the display for 2 seconds and then the repeat indicator (E) lights. The track being currently played is played repeatedly. • DISC REPEAT The indication “DISC RPT” appears in the display for 2 seconds and then the repeat indicator (E) lights.
  • Page 182 OTHER CONTROLS AND EQUIPMENT To change the selection on a CD: Anti-Theft Feature • To advance to the next track on a CD, push the upper part of the switch (4) Type 1 AM/FM/XM CD PLAYER WITH CD CHANGER CONTROL briefly.
  • Page 183 (1) Power on/off knob NOTE: (2) Track up button/Fast forward button Establish your PIN by combining numbers (3) Preset buttons (1 to 6) from 1 to 6 into any 4-digit number. If you forget your PIN, when you remove the bat- The anti-theft feature is intended to dis- tery for repair etc., you will no longer be courage theft or the audio system by pre-...
  • Page 184 OTHER CONTROLS AND EQUIPMENT Confirming Your Personal Identifi- cation Number (PIN) When the main power source is discon- nected such as when you exchange your battery, etc, you will have to confirm your PIN to be able to use the audio system. To confirm your PIN: 66J121 2) Press the power on/off knob (1) while...
  • Page 185 OTHER CONTROLS AND EQUIPMENT Cause Remedy Contact your authorized SUZUKI dealer. Contact your authorized SUZUKI dealer. Cause Remedy Tune correctly to the station frequency. Select stations by manual tuning.
  • Page 186 If a problem should occur, the display shows the type of error. Refer to the table below and take proper measures to correct the problem. If the problem is corrected, the unit will operate normally. Error display If an error display not listed above appears, turn off the unit and contact your SUZUKI dealer. 5-35 Measures to be taken CD/CD changer “Mechanical error”.

  • Page 187: Fuel Filler Cap

    Fuel Filler Cap of the driver’s seat and can be locked by simply closing the door. EXAMPLE Open 64J085 To remove the fuel filler cap: EXAMPLE 1) Open the fuel filler door. 2) Remove the cap by turning it counter- clockwise.

  • Page 188: Engine Hood

    Engine Hood WARNING If you need to replace the fuel cap, use a genuine SUZUKI cap. Use of an improper cap can result in a malfunc- tion of the fuel system or emission control system. It may also result in fuel leakage in the event of an acci- dent.

  • Page 189: Interior Light Switch

    Sun Visor 64J112 3) Continue to lift up the hood until it is high enough to support with the prop The sun visors can be pulled down to block rod. glare coming through the windshield, or they can be unhooked and turned to the To close the engine hood: side to block glare coming through the side 1) Lift the hood up slightly and remove the...

  • Page 190: Luggage Compartment Light

    OTHER CONTROLS AND EQUIPMENT ON (1) The light comes on and stays on regard- EXAMPLE less of whether the door is open or closed. DOOR (2) The light comes on when the door is opened. After closing all doors (including the tail- gate), the light will remain on for about 15 seconds and then fade out.

  • Page 191: Spot Light

    remains off regardless of whether the Spot Light door(s) is(are) opened or closed. EXAMPLE Push the switch (1) to turn on the light and push it again to turn off the light. OTHER CONTROLS AND EQUIPMENT Accessory Socket (if equipped) EXAMPLE 65J093 EXAMPLE...

  • Page 192: Cigarette Lighter And Ashtray (If Equipped)

    OTHER CONTROLS AND EQUIPMENT The accessory socket will work when the Cigarette Lighter and Ashtray ignition switch is in the “ACC” or “ON” posi- (if equipped) tion. Cigarette Lighter 12-volt accessory sockets are located both on the center console and on the left side of the luggage compartment.

  • Page 193: Sunroof (If Equipped)

    Ashtray Sunroof (if equipped) You can tilt or slide the sunroof by operat- EXAMPLE ing the “TILT” part of the sunroof switch or the “SLIDE” part of the sunroof switch when the ignition switch is in the “ON” posi- tion. There is a system to prevent being pinched by the sunroof.
  • Page 194 OTHER CONTROLS AND EQUIPMENT 79K098 To slide the sunroof rearward, push the The sun shade will open automatically and “SLIDE OPEN” part (2) of the sunroof cannot be closed when the sunroof is slid switch. To side the sunroof forward, push rearward.

  • Page 195: Assist Grips (If Equipped)

    Do not put your body weight on the roof around the sunroof such as by sitting on it. • Be sure to close the sunroof when you leave the vehicle unattended. • Periodically inspect the guide rail for dirt and clean it if any dirt has accumulated. 65D612 WARNING •...

  • Page 196: Coat Hooks (If Equipped)

    OTHER CONTROLS AND EQUIPMENT Coat Hooks (if equipped) Glove Box UNLOCK 64J137 You can hang clothing on the coat hooks. To open the glove box, pull the latch lever. These hooks are not designed for large or To close it, push the lid until it latches heavy items.

  • Page 197: Cup Holder And Storage Bin (If Equipped)

    Cup Holder and Storage Bin CAUTION (if equipped) If you park your vehicle outdoors in Cup holders and a storage bin are pro- direct sunlight or in hot weather, the vided as shown. eyeglasses compartment can get very hot since it is close to the roof. So, when parking in such conditions: •...

  • Page 198: Front Seat Back Pocket (If Equipped)

    OTHER CONTROLS AND EQUIPMENT Front Seat Back Pocket WARNING (if equipped) Do not use the cup holder or the stor- age bin to hold cups containing hot EXAMPLE liquids or sharp-edged, hard or breakable objects. Objects in these bins may be thrown about during a sudden stop or impact, and could cause personal injury.

  • Page 199: Armrest

    Armrest Luggage Compartment Cover Luggage or other cargo placed in the lug- Center Console Armrest gage compartment can be hidden from view by a luggage compartment cover. However, the luggage compartment covers are not designed to support items loaded on top of them, and may get damaged if used as a shelf.
  • Page 200 OTHER CONTROLS AND EQUIPMENT rear front 3) Lift up both ends of the cover to disen- gage the attachment points (b). 66J204 2) Fold and roll the cover forward. 4) Place one end of the cover in the quar- ter window opening (c) so enough 5-49 clearance is established on the other end to swing the cover down and out.
  • Page 201 To stow a luggage compartment cover To reinstall the luggage compartment on the floor of the rear luggage room: cover: 1) Fold/roll cover, and place one end in the quarter window opening (c) to swing the other end into position. 66J207 Tilt the cover, and fit it onto floor of the rear luggage room.

  • Page 202: Underfloor Bins (If Equipped)

    OTHER CONTROLS AND EQUIPMENT Underfloor Bins (if equipped) EXAMPLE 66J210 3) Unroll/unfold the cover as you secure the other latches (e). Pull up the straps (A) to open the bin. Do not allow items in the bins to extend above the top of the bin. Oth- erwise, the bin or luggage floor may be damaged.

  • Page 203: Roof Rails Or Roof Rack Anchors (If Equipped)

    You can use the roof rails or the roof rack anchors to attach the optional roof rack which is available at your SUZUKI dealer. If you use a roof rack, observe the instruc- tions and precautions in this section and provided with the roof rack.

  • Page 204: Homelink® (If Equipped)

    OTHER CONTROLS AND EQUIPMENT • Mount and secure the cargo onto the roof rack properly according to the instructions provided. Be sure to stow • Abrupt maneuvers or failure to the heaviest items at the bottom and dis- properly secure cargo can allow the tribute the cargo as evenly as possible.
  • Page 205 any garage door opener model manufac- HomeLink tured before April 1, 1982). A garage door ming HomeLink that cannot detect an object – signaling the door to stop and reverse – does not meet current U.S. federal safety standards. For ®...
  • Page 206 OTHER CONTROLS AND EQUIPMENT ® HomeLink ” steps 6–8 to complete the 6) At the garage door opener receiver programming rolling code (motor-head unit) in the garage, locate equipped device (most commonly a the “learn” or “smart” button. This can garage door opener).

  • Page 207: Frame Hooks

    ® Using HomeLink Reprogramming a Single HomeLink To operate, simply press and release the ® programmed HomeLink button. Activation To program a device to HomeLink will now occur for the trained device (i.e. HomeLink garage door opener, gate operator, secu- low these steps: rity system, entry door lock, home/office 1) Press and hold the desired HomeLink...
  • Page 208 OTHER CONTROLS AND EQUIPMENT Frame hooks are provided at the front and rear of the vehicle. To access the front hook, unhook the lower part of the cover (1) and then remove the cover (1). WARNING Do not use the frame hooks to tow another vehicle or to have your vehi- cle towed on the road or highway.

  • Page 209: Vehicle Loading And Towing

    VEHICLE LOADING AND TOWING VEHICLE LOADING AND TOWING Vehicle Loading ... 6-1 Trailer Towing ... 6-2 Towing Your Vehicle (recreational towing) ... 6-7 54G215 79K20-03E...

  • Page 210: Vehicle Loading

    Vehicle Loading: 11 VEHICLE LOADING AND TOWING Vehicle Loading 54G307 Your vehicle was designed for specific weight capacities. The weight capacities of your vehicle are indicated by the Gross Vehicle Weight Rating (GVWR), the Gross Axle Weight Rating (GAWR, front and rear) and the Vehicle Capacity Weight.

  • Page 211: Trailer Towing

    Trailer Towing: 5, 11, 13 Trailer Towing You can use your SUZUKI to tow a trailer, but you should always observe the require- ments and recommendations in this sec- tion. If you intend to tow a trailer, it is essential to select a trailer and trailer tow- ing equipment which are compatible.
  • Page 212 Trailer Towing: 5, 11, 13 VEHICLE LOADING AND TOWING Tires WARNING When towing a trailer, it is very important for your vehicle and trailer to have properly inflated tires. Your vehicle’s tires should be inflated to the recommended pressures listed on your vehicle’s Tire Inflation Pres- sure label.
  • Page 213 Trailer Towing: 5, 11, 13 Tongue Weight 60A380 Tongue Weight is the downward force exerted on the hitch by the trailer coupler, with the trailer fully loaded and the coupler at its normal towing height. Cargo should be distributed so that tongue weight is approximately 10% of gross trailer weight.
  • Page 214 Trailer Towing: 5, 11, 13 VEHICLE LOADING AND TOWING WARNING Never overload your trailer or your vehicle. Gross Trailer Weight must never exceed 1350 kg (3000 pounds). Gross Combined Weight must never exceed 3400 kg (7500 pounds) for 2WD or 3450 kg (7600 pounds) for 4WD.
  • Page 215 Trailer Towing: 5, 11, 13 WARNING (Continued) • Avoid “riding” the brakes. “Riding” the brakes could cause the brakes to overheat, resulting in reduced braking efficiency. engine braking as much as possible. • Because added trailer weight, your engine may overheat on hot days when going up long or steep hills.
  • Page 216 Towing Your Vehicle (recreational towing): 13 VEHICLE LOADING AND TOWING Towing Your Vehicle (recreational towing) Your vehicle may be towed behind another vehicle (such as a motorhome), provided you use the proper towing method speci- fied for your vehicle. The towing method you must use depends on the specifica- tions of your vehicle: whether it is a 2- wheel drive (2WD), 4-wheel drive (4WD)
  • Page 217 Towing Your Vehicle (recreational towing): 13 WARNING When you tow your vehicle, follow the instructions below to avoid acci- dents and damage to your vehicle. In addition, be sure to observe govern- ment and local requirements regard- ing vehicle lighting and trailer hitches or tow bars.
  • Page 218 Towing Your Vehicle (recreational towing): 13 VEHICLE LOADING AND TOWING 7) Release the parking brake. Stop towing the vehicle every 300 km (200 miles). Start the engine. With the manual transmission lever in 2nd gear (or the auto- matic transmission lever in “D”) and the transfer switch in neutral, rev the engine for about one minute with the clutch engaged (if equipped), to circulate oil in the transfer...
  • Page 219 Towing Your Vehicle (recreational towing): 13 4WD Vehicle Without a Transfer Switch 54G586 54G585 VEHICLE LOADING AND TOWING 2WD Vehicle 1) Secure the rear wheels on a towing dolly according to the instructions pro- vided by the dolly manufacturer. 2) Turn the ignition key to the “ACC” posi- tion to unlock the steering wheel.
  • Page 220 Towing Your Vehicle (recreational towing): 13 VEHICLE LOADING AND TOWING TOWING METHOD B FRONT WHEELS ON THE GROUND AND REAR WHEELS ON A DOLLY. 6-11 52D082 79K20-03E...

  • Page 221: Inspection And Maintenance

    INSPECTION AND MAINTENANCE INSPECTION AND MAINTENANCE Maintenance Schedule ... 7-2 Periodic Maintenance Schedule ... 7-3 Maintenance Recommended under Severe Driving Conditions ... 7-7 Drive Belt ... 7-9 Engine Oil and Filter ... 7-10 Engine Coolant ... 7-13 Air Cleaner ... 7-16 Spark Plugs ...

  • Page 222: Inspection And Maintenance

    • Do not get under your vehicle if it is electrical service work on your supported only with the portable SUZUKI. Do not touch air bag sys- jack provided in your vehicle. tem components or wires. The wires are wrapped with yellow tape or yellow tubing, and the couplers are yellow for easy identification.

  • Page 223: Maintenance Schedule

    SUZUKI recommends that mainte- nance on items marked with an aster- performed your authorized SUZUKI dealer or a quali- fied service technician. If you are qualified, you may perform mainte- nance on the unmarked items by referring to the instructions in this section.

  • Page 224: Periodic Maintenance Schedule

    #2: Be sure to perform the engine coolant level check under the daily inspection in “OPERATING YOUR VEHICLE” section. If you replace the engine coolant other than the SUZUKI LLC: Super (Blue), follow the schedule of SUZUKI LLC: Standard (Green).
  • Page 225 #2: Be sure to perform the engine coolant level check under the daily inspection in “OPERATING YOUR VEHICLE” section. If you replace the engine coolant other than the SUZUKI LLC: Super (Blue), follow the schedule of SUZUKI LLC: Standard (Green).

  • Page 226: Inspection And Maintenance

    Periodic Maintenance Schedule: 1, 2, 3, 4, 5, 6, 9, 10 INSPECTION AND MAINTENANCE R: Replace or change I : Inspect, clean, adjust, lubricate or replace as necessary Interval: This interval should be judged by miles (x 1000) odometer reading or months, whichever comes km (x 1000) first.
  • Page 227 Periodic Maintenance Schedule: 1, 2, 3, 4, 5, 6, 9, 10 R: Replace or change I : Inspect, clean, adjust, lubricate or replace as necessary Interval: This interval should be judged by miles (x 1000) odometer reading or months, whichever comes km (x 1000) first.

  • Page 228: Maintenance Recommended Under Severe Driving Conditions

    Maintenance Recommended under Severe Driving Condi- tions: 1, 2, 3, 4, 5, 6, 9, 10 INSPECTION AND MAINTENANCE Maintenance Recommended under Severe Driving Conditions If the vehicle is usually used under the conditions corresponding to any severe condition code given below, it is recommended that appli- cable maintenance operation be performed at the particular interval shown in the chart below.
  • Page 229 Maintenance Recommended under Severe Driving Condi- tions: 1, 2, 3, 4, 5, 6, 9, 10 Severe Maintenance Condition Code – B – – E H Automatic transmission (A/T) fluid – B – – E H Transfer, Differential and Extension oil –...

  • Page 230: Drive Belt

    You do not need check it for ten- sion as it has an automatic tensioner. If you need to replace or adjust the belt have it done by your SUZUKI dealer. L4 2.4 L V6 3.2 L →: 100 N (22 lbs, 10 kg) press...

  • Page 231: Engine Oil And Filter

    Engine Oil and Filter: 1, 2 Engine Oil and Filter Specified Oil “Starburst” 79K096 Use engine oil with the American Petro- leum Institute Certified For Gasoline Engines “Starburst” symbol. We highly recommend you use SAE 5W- 30 oil. CAUTION Failure to use the recommended oil can result in engine damage.
  • Page 232 Engine Oil and Filter: 1, 2 INSPECTION AND MAINTENANCE Refilling EXAMPLE Open Close 81A147 Remove the oil filler cap and pour oil slowly through the filler hole to bring the oil level to the upper limit on the dipstick. Be careful not to overfill.
  • Page 233 NOTE: • When it is difficult to remove the oil filter, we recommend you take your vehicle to your SUZUKI dealer for oil filter replace- ment. • For 3.2 L engine, since special proce- dures are required, we recommend you take your vehicle to your SUZUKI dealer for oil filter replacement.

  • Page 234: Engine Coolant

    Genuine Coolant or equivalent. 64J151 NOTE: If you replace the engine coolant other than the SUZUKI LLC: Super (Blue), follow EXAMPLE the schedule of SUZUKI LLC: Standard (Green). To see the detail of the mainte- nance schedule, refer to “Periodic Mainte- nance Schedule”...
  • Page 235 70/30 coolant to distilled water will cause over- heating conditions. • Do not use straight coolant nor plain water (except SUZUKI LLC: Super (Blue)). • Do not add extra inhibitors or addi- tives. They may not be compatible with your cooling system.
  • Page 236 Automatic Transmission Fluid: 10 Engine Coolant: 1, 2 INSPECTION AND MAINTENANCE Engine Coolant Replacement Open Close 66J151 1) When the engine is cool, remove the radiator cap by turning it slowly to the left until a “stop” is felt. Do not press down while turning the cap.

  • Page 237: Air Cleaner

    Engine Coolant: 1, 2 Air Cleaner EXAMPLE 66J167 If the air cleaner is clogged with dust, there will be greater intake resistance, resulting in decreased power output and increased fuel consumption. Check and clean periodically according to the following procedure: 1) Take off the air cleaner case cover.

  • Page 238: Gear Oil

    For the speci- fied plugs, refer “SPECIFICATIONS” section at the end of this book. If you wish to use a brand of spark plug other than the specified plugs, consult your SUZUKI dealer. 54G095 65D594 79K20-03E...
  • Page 239 Windshield Washer Fluid: 3 Air Cleaner: 1, 2 API GRADE Transmission/ GL-4 Extension case Transfer case GL-5 Front (Hypoid gear oil) Differential Rear INSPECTION AND MAINTENANCE Manual transmission Extension case (2WD) 52D087 Transfer case (1) Oil filler and level plug (2) Oil drain plug 66J005 (1) Oil filler and level plug...
  • Page 240 When tightening these plugs, apply sealing compound “SUZUKI Bond No. 1215” or equivalent to the plug threads to prevent oil leakage and tighten them to the specified torque shown below.

  • Page 241: Clutch Pedal

    1) To warm up the transmission fluid, drive depressed, have the clutch inspected by the vehicle or idle the engine until the your SUZUKI dealer. If the clutch fluid level temperature gauge indicates normal is near the “MIN” line, fill it up to the “MAX”...

  • Page 242: Brakes: 6

    The handle of the A/T fluid dipstick is col- you trust this job to your authorized ored red for easy identification. SUZUKI dealer. FULL HOT LOW HOT 65D109 6) Remove the dipstick, clean it and push it back in until the cap seats.

  • Page 243: Steering Wheel: 6

    Should the light come on, immedi- cal attention. Wash thoroughly after ately ask your SUZUKI dealer to handling. Solution can be poisonous inspect the brake system. to animals. Keep out of the reach of •...

  • Page 244: Tires: 6

    If the pedal to floor carpet distance as 7-23 measured above is less than the minimum distance required, have your vehicle inspected by your SUZUKI dealer. NOTE: When measuring the distance between the brake pedal and floor wall, push in the floor...
  • Page 245 If the parking brake is not properly adjusted or the brakes drag after the lever has been fully released, have the parking brake inspected and/or adjusted by your SUZUKI dealer. INSPECTION AND MAINTENANCE Steering Wheel Power Steering (if equipped) EXAMPLE “c”...
  • Page 246 Tires: 6 INSPECTION AND MAINTENANCE Tires For safe operation of your vehicle, it is important that the tires be the correct type and size, in good condition, and properly inflated. Be sure to follow the requirements and recommendations in this section. Tire Sidewall Labeling Useful information about a tire is molded into its sidewall.
  • Page 247 The following illustration shows an example of a typical passenger car tire size. EXAMPLE E. Rim Diameter Your SUZUKI is equipped with tires which are all the same type and size. This is important to ensure proper steering and han- 67D028 dling of the vehicle.
  • Page 248 Tires: 6 INSPECTION AND MAINTENANCE Tire Inflation Pressure Tire inflation pressure should be checked when the tire is cold. “Cold tire inflation pressure” is the pressure in a tire that has been driven less than 1 mile (1.6 km) or has been standing for three hours or more.
  • Page 249 Tires: 6 tire gauge until you reach the cor- rect pressure. 5) If the air pressure is too low, fill the tire with air at a service station until it reaches the recommended pres- sure. 6) Make sure all tires have the same air pressure (unless the owner’s manual indicates otherwise).
  • Page 250 5) Check that there are no nails, stones or other objects sticking into the tires. 7-29 WARNING Your SUZUKI is equipped with Replacing the wheels and tires tires which are all the same type equipped on your vehicle with and size. This is important to...
  • Page 251 U.S. Consult your SUZUKI dealer or tire retailer for help in choosing the correct replacement tires for your vehicle. Quality grades can be found where...
  • Page 252 Tires: 6 INSPECTION AND MAINTENANCE Tire Rotation 4-tire rotation 65D459 To avoid uneven wear of your tires and to prolong their life, rotate the tires as illustrated. Tires should be rotated as recommended in the periodic mainte- nance schedule. After rotation, adjust front and rear tire pressures to the specification listed on your vehicle’s Tire and Loading Information Label.

  • Page 253: Battery: 9

    For improved traction in severe winter conditions, SUZUKI recommends mounting radial snow tires on all four wheels. Snow tires must be the same size as the standard tires. Also be sure...
  • Page 254 Fuses: 7 INSPECTION AND MAINTENANCE Recommended Inflation Pressure – the cold tire inflation pressure recom- mended by a manufacturer. Rim – metal support for a tire or tire and tube assembly upon which the tire beads are seated. Vehicle Capacity Weight – the rated cargo and luggage load plus 68 kilo- grams (150 lbs) times the vehicle’s designated seating capacity.
  • Page 255 Fuses: 7 exceed the total load capacity of the vehicle. Total Load Capacity – Maximum per- missible weight a vehicle can carry including the weight of all the occu- pants, accessories, cargo, plus trailer tongue weight (if towing a trailer). The weight of any accessories already installed on your vehicle at the time of purchase, or that you or the dealer...
  • Page 256 Fuses: 7 Headlight Aiming: Bulb Replacement: 7 INSPECTION AND MAINTENANCE gers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs (1400 – 750 (5 x 150) = 650 lbs). 5) Determine the combined weight of luggage and cargo being loaded on the vehicle.

  • Page 257: Emergency Service

    Bulb Replacement: 7 Battery EXAMPLE 60A269 WARNING Batteries produce flammable hydro- gen gas. Keep flames and sparks away from the battery or an explosion may occur. Never smoke when work- ing near the battery. WARNING When checking or servicing the bat- tery, disconnect the negative cable.
  • Page 258 SUZUKI engine compartment. If the main fuse dealer. Always use a genuine SUZUKI blows, no electrical component will func- replacement. Never use a substitute tion. If a primary fuse blows, no electrical...

  • Page 259: Fuse Under The Dash Board

    Bulb Replacement: 7 Fuse under the Dash Board Fuse box 64J192 79K057 INSPECTION AND MAINTENANCE DOME Dome lamp fuse STOP Stop lamp fuse – – Blank Accessory socket ACC 3 fuse CRUISE Cruise control fuse Cigar or Accessory ACC 2 socket fuse Wiper fuse Ignition signal &...

  • Page 260: Headlight Aiming

    SUZUKI dealer. NOTE: Make sure that the fuse box cover always carries spare fuses. 7-39 Headlight Aiming Since special procedures are required, we recommend you take your vehicle to your SUZUKI dealer for headlight alignment. BLOWN 60A243 BLOWN 81A283 79K20-03E...
  • Page 261 Frequent replacement of a bulb indi- cates the need for an inspection of the electrical system. This should be carried out by your SUZUKI dealer. NOTE: If it is difficult to replace headlight bulbs or clearance light bulbs due to under-hood components trust this job to your dealer.
  • Page 262 Wiper Blades: 3 INSPECTION AND MAINTENANCE Spot Light (if equipped) Pull down the lens by using a plain screw driver covered with a soft cloth as shown. Ceiling-mount type (if equipped) 79K061 Remove the bulb holder by turning it coun- terclockwise.
  • Page 263 Wiper Blades: 3 Front Fog Light 79K090 1) Insert a flat blade screw driver into the hole (2) and remove the clips (1) by twist the driver as shown in the illustra- tion. 2) Remove the bolt (3) by a Phillips-head screw driver.
  • Page 264 Air Conditioning System: 4 INSPECTION AND MAINTENANCE Other General Lights Bulb holder EXAMPLE 54G123 (1) Removal (2) Installation To remove a bulb holder from a light hous- ing, turn the holder counterclockwise and pull it out. To install the holder, push the holder in and turn it clockwise.
  • Page 265 Since special procedures are required, we recommend you take your vehicle to your SUZUKI dealer for the bulbs of high-mount stop light replacement. 64J166 64J181 To remove a high-mounted stop light hous-...
  • Page 266 INSPECTION AND MAINTENANCE 64J182 2) Release the claws of the light housing 3) Close the tailgate. Remove a high- by the flat head etc. through the service mounted stop light housing (2) from the holes as shown in the illustration. tailgate.
  • Page 267 NOTE: Some wiper blades may be different from the ones described here depending on vehicle specifications. If so, consult your SUZUKI dealer for proper replacement method. INSPECTION AND MAINTENANCE 52D102 70G119 2) Squeeze lock lever (1) towards wiper arm (2) and remove the wiper frame from the arm as shown.
  • Page 268 INSPECTION AND MAINTENANCE 60A260 3) Pull the locked end of the wiper blade (3) Retainer firmly to unlock the blade and slide the blade out as shown. 4) If the new blade is provided without the two metal retainers, move them from the old blade to the new one.
  • Page 269 For rear wipers: NOTE: Do not flex the wiper blade frame end more than necessary. If you do, it can break off. 80G146 1) Hold the wiper arm away from the win- dow. 2) Remove the wiper frame from the arm as shown.

  • Page 270: Air Conditioning System

    INSPECTION AND MAINTENANCE Windshield Washer Fluid fluid tank. If the fluid level is near empty, refill it. Front and rear (if equipped) Use a good quality windshield washer EXAMPLE fluid, diluted with water as necessary. Do not use “anti-freeze” solution in the windshield washer reservoir.

  • Page 271: Emergency Service

    EMERGENCY SERVICE EMERGENCY SERVICE Tire Changing Tool ... 8-1 Spare Tire Nut Lock (if equipped) ... 8-1 Jacking Instructions ... 8-2 Changing Wheels ... 8-3 Jump Starting Instructions ... 8-7 Towing a Disabled Vehicle ... 8-8 If the Starter Does Not Operate ... 8-8 If the Engine is Flooded ...

  • Page 272: Tire Changing Tool

    Jacking Instructions: 5 EMERGENCY SERVICE Tire Changing Tool 64J124 The jack, wheel brace and jack handle are stowed in the rear left corner of the lug- gage compartment. Remove the cover to access the tools. To remove the jack, turn its shaft counter- clockwise and pull the jack out of the stor- age bracket.

  • Page 273: Jacking Instructions: 5

    Jacking Instructions: 5 Jacking Instructions 75F062 1) Place the vehicle on level, hard ground. 2) Set the parking brake firmly and shift into “P” (Park) if your vehicle has an automatic transmission, or shift into “R” (Reverse) if your vehicle has a manual transmission.

  • Page 274: Changing Wheels

    Jump Starting Instructions: 7 EMERGENCY SERVICE WARNING • Use the jack only to change wheels on level, hard ground. • Never jack up the vehicle on an inclined surface. • Never raise the vehicle with the jack in a location other than the designated jacking point near the wheel to be changed.

  • Page 275: Towing A Disabled Vehicle: 6

    Jump Starting Instructions: 7 Towing a Disabled Vehicle: 6 If the Starter Does Not Operate: 2, 9 NOTE: Remove the full wheel cover from the bot- tom part to the upper part. Otherwise, the claws may be broken. (Half cover type) 78K060 NOTE: If your vehicle is equipped with the half...

  • Page 276: If The Engine Is Flooded

    If you do not have a torque wrench, have the wheel nut torque checked by an authorized SUZUKI dealer. To install the wheel: 78K061 1) Install the wheel with both hands to the spare tire carrier (1) as shown in the illustration.
  • Page 277 For improved using this spare: traction • Be aware that your vehicle will han- SUZUKI recommends mounting radial dle differently with this temporary snow tires on all four wheels. Snow tires spare. must be the same size as the standard •...

  • Page 278: Jump Starting Instructions

    • If your battery discharges repeat- edly, for no apparent reason, have your vehicle inspected by an autho- rized SUZUKI dealer. • To avoid harm to yourself or dam- 1) Use only a 12 volt battery to jump start age to your vehicle or battery, fol- your vehicle.

  • Page 279: If The Starter Does Not Operate

    2) If the headlights remain bright, check the fuses. If the reason for failure of the starter is not obvious, there may be a major electrical problem. Have the vehi- inspected SUZUKI dealer. CAUTION your authorized 79K20-03E...

  • Page 280: If The Engine Is Flooded

    EMERGENCY SERVICE If the Engine is Flooded If the Engine Overheats If the engine is flooded with gasoline, it The engine could overheat temporarily may be hard to start. If this happens, press under severe driving conditions. If the the accelerator pedal all the way to the engine coolant temperature gauge indi- floor and hold it there while cranking the cates overheating during driving:...
  • Page 281 66J191 WARNING • It is hazardous to remove the radia- tor cap when the water temperature is high, because scalding fluid and steam may be blown out under pressure. The cap should only be taken off when the coolant temper- ature has lowered.
  • Page 282 EMERGENCY SERVICE MEMO 8-11 79K20-03E...

  • Page 283: Appearance Care

    APPEARANCE CARE APPEARANCE CARE Corrosion Prevention ... 9-1 Vehicle Cleaning ... 9-3 60G412 79K20-03E...

  • Page 284: Corrosion Prevention

    Corrosion Prevention: 5 APPEARANCE CARE Corrosion Prevention It is important to take good care of your vehicle to protect it from corrosion. Listed below are instructions for how to maintain your vehicle to prevent corrosion. Please read and follow these instructions carefully.
  • Page 285 UV rays in sunlight, and can reduce the amount of dust and air pollution reaching the surface. Your SUZUKI dealer can help you select the right cover for your vehicle. APPEARANCE CARE...
  • Page 286 Vehicle Cleaning: 5 APPEARANCE CARE Vehicle Cleaning 76G044S WARNING When cleaning the interior or exterior of the vehicle, NEVER USE flammable solvents such lacquer thinners, gas- oline, benzene or cleaning materials such as bleaches and strong house- hold detergents. The materials could cause personal injury or damage to the vehicle.
  • Page 287 Vehicle Cleaning: 5 Washing WARNING • Never attempt to wash and wax your vehicle with the engine run- ning. • When cleaning the underside of the body and fender, where there may be sharp-edged parts, you should wear gloves and a long-sleeved shirt to protect your hands and arms from being cut.
  • Page 288 APPEARANCE CARE MEMO 79K20-03E...

  • Page 289: General Information

    GENERAL INFORMATION GENERAL INFORMATION Identification Numbers ... 10-1 Safety Certification Label ... 10-2 Emission Compliance Label (for U.S.A.) ... 10-2 Warranties ... 10-2 On-Board Vehicle Computers and Event Data Recorders ... 10-3 Reporting Safety Defects ... 10-4 54G072 79K20-03E...

  • Page 290: Identification Numbers

    Identification Numbers: 2, 5 GENERAL INFORMATION Identification Numbers Vehicle Identification Number EXAMPLE (for some vehicles) 60G152 64J197 10-1 The Vehicle Identification Number (VIN) 3.2 L engine model may be found in the two locations shown in the above illustrations. This number is used to register the vehicle.

  • Page 291: Safety Certification Label: 6

    For U.S.A. The following warranties are provided with your vehicle: • New Vehicle Limited Warranty • Limited Warranty For SUZUKI Parts or Accessories • Emission Components Defect Warranty • Emission Performance Warranty 60A412 The EPA emission compliance label is located under the hood.

  • Page 292: On-Board Vehicle Computers And Event Data Recorders

    SUZUKI’s defense of litiga- tion through the discovery process, or as required by law. research...

  • Page 293: Reporting Safety Defects

    For vehicles registered for use and NHTSA cannot become involved in principally operated in Canada please individual problems between you, your contact Suzuki Canada Inc. at 1-905- dealer, or American Suzuki Motor 889-2677 extension 2254 or write to: Corp. Suzuki Canada Inc.
  • Page 294 GENERAL INFORMATION MEMO 10-5 79K20-03E...

  • Page 295: Fuses And Protected Circuits

    Fuses and Protected Circuits: 7 FUSES AND PROTECTED CIRCUITS COLOR (AMPS) BLUE (15) CPRSR YELLOW (20) O2 HTR BLUE (15) THR MOT YELLOW (20) MAIN FUSE CLEAR (25) RR DEF BLUE (15) HORN YELLOW (20) FR FOG YELLOW (20) MRR HTR GREEN (40) FR BLW (10)
  • Page 296 Fuses and Protected Circuits: 7 FUSES AND PROTECTED CIRCUITS COLOR (AMPS) (11) RED (50) ABS 1 (12) YELLOW (20) (13) – – (14) RED (10) H/L L MAIN FUSE (15) RED (10) H/L R (16) RED (10) (17) GREEN (40) ST MTR (18) GREEN (40)
  • Page 297 FUSES IN FUSE BOX RED (10) DOME Dome lamp fuse RED (10) STOP Stop lamp fuse – – Blank BLUE (15) ACC 3 Accessory socket fuse RED (10) CRUISE Cruise control fuse BLUE (15) ACC 2 Cigar or Accessory socket fuse YELLOW (20) Wiper fuse BLUE (15)
  • Page 298 FUSES AND PROTECTED CIRCUITS MEMO 11-4 79K20-03E...

  • Page 299: Specifications

    Specifications: 1, 2, 5, 6, 7, 10, 11 SPECIFICATIONS NOTE: Specifications are subject to change with- out notice. ITEM: Dimensions Overall length Overall width Overall height Wheelbase Tread Minimum running ground clearance ITEM: Weight Gross axle weight rating Gross vehicle weight rating Vehicle capacity weight 4WD: 4-wheel drive M/T: Manual transmission...
  • Page 300 Specifications: 1, 2, 5, 6, 7, 10, 11 SPECIFICATIONS ITEM: Engine Type Number of cylinders Bore Stroke Piston displacement Compression ratio ITEM: Electrical Ignition timing Standard spark plug Battery Fuses 12-2 J24B (16V DOHC) N32A (24V DOHC) 92.0 mm (3.62 in.) 89.0 mm (3.50 in.) 90.0 mm (3.54 in.) 85.6 mm (3.37 in.)
  • Page 301 Specifications: 1, 2, 5, 6, 7, 10, 11 ITEM: Lights Headlight Low beam High beam Front fog light Turn signal light front rear Parking light Brake/tail light License plate light Reversing light High mount stop light Door illumination light Dome light Spot light Center light Rear light...
  • Page 302 SPECIFICATIONS ITEM: Steering Toe-in Camber angle Caster angle ITEM: Capacities (approx.) Coolant Fuel tank Engine oil (replaced with filter) Transmission oil Differential gear oil front rear Transfer gear box oil with a transfer switch without a transfer switch Extension case oil 12-4 front 0 ±...

  • Page 303: Index

    INDEX Symbols “AIR BAG” Light ...2-60 “CRUISE” Indicator Light ...2-61 “ESP OFF” Indicator Light 2-58 3-32 “ESP” (Electronic Stability Program) Warning Light ...2-58 “ESP” Warning Light ...3-32 “SET” Indicator Light ...2-61 Numerics 4-Speed Automatic Transmission ...3-13 5-Speed Automatic Transmission ...3-11 A/T Selector Position ...2-66 Accelerator Pedal ...3-8 Accessory Socket ...5-40...
  • Page 304 INDEX Daily Inspection Checklist ...3-2 Daytime Running Light (D.R.L.) Indicator Light ...2-62 Daytime Running Light (D.R.L.) System ...2-76 Door Locks ...2-1 Drive Belt ...7-9 Driver’s Seat Belt Reminder Light ...2-60 Driving range ...2-66 Electronic Stability Program (ESP®) ...3-30 Emergency Locking Retractor (ELR) ...2-28 Emission Compliance Label (for U.S.A.) ...10-2 Engine Block Heater ...3-10 Engine Coolant ...7-13...
  • Page 305 If You Can Not Shift Automatic Transmission Gearshift Lever Out of “P” (PARK) ...3-15 If Your Vehicle Gets Stuck ...4-6 Ignition Key Reminder ...2-1 Ignition Switch ...3-3 Illumination Indicator Light ...2-62 Important Vehicle Design Features To Know ...4-1 Improving Fuel Economy ...4-3 Information Display ...2-65 Inside Rearview Mirror ...2-17 Installation with Lap-Shoulder Seat Belts...

  • Page 306: Roof Rails Or Roof Rack Anchors

    INDEX Outside Rearview Mirrors ...2-17 Overhead Console Box ...5-45 Parking Brake Lever ... 3-7 Pedals ...3-8 Periodic Maintenance Schedule ...7-3 Power Assisted Brakes ...3-28 Power Door Locking System ...2-2 Power Mirror Control ...2-18 Power Steering ...7-24 Power Steering Fluid ...7-24 Power Window Controls ...2-15 Radio Antenna ...5-8 Rear Seats ...2-22...
  • Page 307 Tire Inflation Pressure ...7-27 Tire Inspection ...7-28 Tire Pressure Monitoring System (TPMS) ...3-36 Tire Rotation ...7-31 Tire Sidewall Labeling ...7-25 Tire Size ...7-26 Tires ...7-25 Towing a Disabled Vehicle ...8-8 Towing Your Vehicle (recreational towing) ...6-7 Traction Control System ...3-30 Trailer Towing ...6-2 Transfer Position Indicator Light ...2-62 Trip meter ...2-68...
  • Page 308 INDEX MEMO 13-6 79K20-03E...
  • Page 309 Prepared by June, 2008 Part No. 99011-79K20-03E Printed in Japan TP306 79K20-03E...

Table of Contents