Xerox VersaLink B7025 Service Manual page 1066

Table 8 Output Codes 012 - Integrated Office Finisher
Code Displayed Name Description
012-013 Sub Paddle Solenoid Energizes the sub paddle solenoid
(SOL12-013).
Do not run with 012-014. Running
these codes at the same time can
cause damage to the machine.
012-014 Sub Paddle Rotation Simultaneously runs the transport
motor (MOT12-095) and energizes
the paddle solenoid (SOL12-013) to
rotate the sub paddle once.
Do not run with 012-013, 012-095,
012-096 or 012-097. Running these
codes at the same time can cause
damage to the machine.
012-017 Set Clamp Motor Runs the set clamp motor (MOT12-
017).
Do not run with 012-061. Running
these codes at the same time can
cause damage to the machine.
012-020 Front Tamper Mot Low Runs the front tamper motor
Front (MOT12-020) at low speed to move
the front tamper forward.
012-021 Front Tamper Mot Mid- Runs the front tamper motor
dle Front (MOT12-020) at mid speed to move
the front tamper forward.
012-022 Front Tamper Mot High Runs the front tamper motor
Front (MOT12-020) at high speed to move
the front tamper forward.
012-023 Front Tamper Mot Low Runs the front tamper motor
Rear (MOT12-020) at low speed to move
the front tamper backward.
012-024 Front Tamper Mot Mid- Runs the front tamper motor
dle Rear (MOT12-020) at mid speed to move
the front tamper backward.
012-025 Front Tamper Mot High Runs the front tamper motor
Rear (MOT12-020) at high speed to move
the front tamper backward.
012-026 Rear Tamper Mot Low Runs the rear tamper motor
Front (MOT12-026) at low speed to move
the rear tamper forward.
General Procedures and Information
dC330
General
On/off. 660ms
timeout.
CAUTION
On/off. 660ms
timeout.
CAUTION
On/off. 250 pulses.
CAUTION
On/off. 100 pulses.
On/off. 100 pulses
On/off. 100 pulses
On/off. 100 pulses.
On/off. 100 pulses
On/off. 100 pulses
On/off. 100 pulses.
Table 8 Output Codes 012 - Integrated Office Finisher
Code Displayed Name
012-027 Rear Tamper Mot Mid-
dle Front
012-028 Rear Tamper Mot High
Front
012-029 Rear Tamper Mot Low
Rear
012-030 Rear Tamper Mot Mid-
dle Rear
012-031 Rear Tamper Mot High
Rear
012-046 Staple Motor FOR-
WARD
012-047 Staple Motor REVERSE Runs the staple motor (MOT12-046)
012-054 Eject Motor Low FOR-
WARD
012-055 Eject Motor High FOR-
WARD
012-056 Eject Motor Low
REVERSE
012-057 Eject Motor High
REVERSE
012-060 Stacker Motor UP
012-061 Stacker Motor DOWN
012-095 Transport Motor Low
012-096 Transport Motor Hi
012-097 Transport Motor Half
Speed
012-110 Registration Clutch ON
April 2017
6-54 Xerox® VersaLink® B7025/B7030/B7035 Multifunction Printer
Description General
Runs the rear tamper motor On/off. 100 pulses
(MOT12-026) at mid speed to move
the rear tamper forward.
Runs the rear tamper motor On/off. 100 pulses
(MOT12-026) at high speed to move
the rear tamper forward.
Runs the rear tamper motor On/off. 100 pulses.
(MOT12-026) at low speed to move
the rear tamper backward.
Runs the rear tamper motor On/off. 100 pulses
(MOT12-026) at mid speed to move
the rear tamper backward.
Runs the rear tamper motor On/off. 100 pulses
(MOT12-026) at high speed to move
the rear tamper backward.
Runs the staple motor (MOT12-046) On/off.
forwards.
On/off. 180ms
in reverse. timeout.
Runs the eject motor (MOT12-054) On/off. 2000 pulses
at low speed to move the ejector out.
Runs the eject motor (MOT12-054) On/off. 2000 pulses
at high speed to move the ejector
out.
Runs the eject motor (MOT12-054) On/off. 2000 pulses
at low speed to move the ejector
home.
Runs the eject motor (MOT12-054) On/off. 2000 pulses
at high speed to move the ejector
home.
Runs the stacker motor (MOT12- On/Off. 80ms time-
060) to drive the stacker tray up. out.
Runs the stacker motor (MOT12- On/Off. 80ms time-
060) to drive the stacker tray down. out.
Runs the transport motor (MOT12- -
095) forward at low speed (equal to
full IOT speed).
Runs the transport motor (MOT12- -
095) forward at high speed (trans-
port speed in finisher).
Runs the transport motor (MOT12- -
095) forward at half speed (equal to
half IOT speed).
Energizes the registration clutch -
(CL12-110).
Launch Issue