Scanlab RTC 5 PC Interface Board Installation And Operation Manual page 224

Starting and Stopping Lists via External
Control Signals and Master/Slave Synchroni-
zation
(n_) set_control_mode_list
us
(n_) set_extstartpos_list
List Handling and Structured Programming
nor
(n_) list_continue ...................................... 317
us
(n_) list_jump_pos ..................................... 319
us
(n_) list_jump_rel ....................................... 321
nor
(n_) list_nop .............................................. 322
us
(n_) list_repeat ........................................... 323
us
(n_) list_until .............................................. 325
nor
(n_) long_delay ......................................... 348
nor
(n_) set_end_of_list .................................. 420
us
(n_) set_list_jump ...................................... 447
nor
(n_) set_wait ............................................. 500
Subroutine Commands
us
(n_) list_call ................................................ 315
us
(n_) list_call_abs ......................................... 316
us
(n_) list_return ........................................... 324
us
(n_) sub_call ............................................... 525
us
(n_) sub_call_abs ........................................ 525
Setting the Laser Parameters
(n_) config_laser_signals_list
(n_) set_auto_laser_params_list
ds
(n_) set_encoder_speed
(n_) set_firstpulse_killer_list
us
(n_) set_laser_delays .................................. 442
(n_) set_laser_pin_out_list
ds
(n_) set_laser_pulses .................................. 445
ds
(n_) set_laser_timing ................................. 446
(n_) set_pulse_picking_list
(n_) set_qswitch_delay_list
(n_) set_softstart_level_list
(n_) set_softstart_mode_list
ds
(n_) set_standby_list .................................. 489
us
(n_) set_vector_control
Setting the Scanner Parameters
(n_) set_delay_mode_list
us
(n_) set_jump_speed .................................. 438
ds
(n_) set_mark_speed .................................. 448
ds
(n_) set_scanner_delays
(n_) set_sky_writing_limit_list
(n_) set_sky_writing_list
(n_) set_sky_writing_mode_list
(n_) set_sky_writing_para_list
®
RTC 5 PC Interface Board
Rev. 1.9 e
10 Commands And Functions
nor
...................... 413
............................ 421
ds
.................... 242
ds
................ 409
............................. 418
us
...................... 423
us
......................... 444
nor
....................... 471
us
....................... 471
nor
...................... 485
var
.................... 487
.............................. 498
mul
......................... 416
............................. 475
us
................... 478
nor
.......................... 478
nor
............... 480
nor
................. 483
Coordinate Transformations
var
(n_) set_angle_list ..................................... 406
var (1)
(n_) set_defocus_list
var
(n_) set_matrix_list ................................... 450
var
(n_) set_offset_list .................................... 463
var (1)
(n_) set_offset_xyz_list
var
(n_) set_scale_list ...................................... 475
Online Positioning
nor
(n_) apply_mcbsp_list
(n_) set_mcbsp_matrix_list
us
(n_) set_mcbsp_rot_list
us
(n_) set_mcbsp_x_list ................................. 458
us
(n_) set_mcbsp_y_list ................................. 459
Direct Laser and Scan Head Control
var
(n_) laser_on_list ....................................... 311
(n_) laser_on_pulses_list
(n_) laser_signal_off_list
nor
(n_) laser_signal_on_list
(n_) para_laser_on_pulses_list
Scanning Raster Images (Bitmaps)
(n_) set_default_pixel_list
var
(n_) set_n_pixel ......................................... 462
var
(n_) set_pixel ............................................. 466
nor
(n_) set_pixel_line ..................................... 467
mul (1)
(n_) set_pixel_line_3d
I/O Commands
us
(n_) clear_io_cond_list
us
(n_) read_io_port_list ................................. 387
(n_) rs232_write_text_list
(n_) set_free_variable_list
us
(n_) set_io_cond_list .................................. 435
us
(n_) set_mcbsp_out ................................... 455
(n_) write_8bit_port_list
ds
(n_) write_da_1_list ................................... 557
ds
(n_) write_da_2_list ................................... 558
ds
(n_) write_da_x_list .................................... 558
ds
(n_) write_io_port_list
(n_) write_io_port_mask_list
(1) Only with enabled 3D option.
nor normal list command
var variable list command
us undelayed short list command
ds delayed short list command
mul list multi-command
............................ 415
........................ 465
.............................. 231
us
........................ 454
.............................. 457
var
........................... 312
nor
.......................... 313
........................... 314
var
................. 375
us
.......................... 414
.......................... 468
............................... 241
var
......................... 396
us
.......................... 433
ds
............................ 557
............................... 559
ds
..................... 560
224