Control Commands - Scanlab RTC 5 PC Interface Board Installation And Operation Manual

10.1.5 Control Commands

DLL Initialization
free_rtc5_dll ........................................... 259
get_rtc_mode ......................................... 277
init_rtc5_dll ............................................. 306
set_rtc4_mode ........................................ 473
set_rtc5_mode ........................................ 473
®
Using Multiple RTC 5 Boards in One
Computer
acquire_rtc .............................................. 227
release_rtc .............................................. 392
rtc5_count_cards .................................... 396
select_rtc ................................................. 403
List Memory Commands
(n_) config_list ............................................... 243
(n_) get_config_list ........................................ 261
(n_) get_list_space ......................................... 272
(n_) load_disk ................................................. 331
(n_) save_disk ................................................. 398
Board Initialization and Field Correction
(n_) get_head_para ....................................... 265
(n_) get_sync_status ...................................... 284
(n_) get_table_para ....................................... 285
(n_) load_correction_file ............................... 328
(n_) load_program_file .................................. 340
(2)
(n_) load_stretch_table
(2)
(n_) load_z_table ...................................... 347
(n_) select_cor_table ...................................... 400
(n_) set_dsp_mode ........................................ 416
(n_) sync_slaves ............................................. 528
(1) Also see the corresponding list commands.
(2) Only with enabled 3D option.
®
RTC 5 PC Interface Board
Rev. 1.9 e
10 Commands And Functions
Laser Mode And Parameters
(n_)
(n_)
(n_)
(n_)
(n_)
(n_)
(n_)
(n_)
(n_)
(n_)
(n_)
(n_)
(n_)
(n_)
(n_)
(n_)
(n_)
Setting The Scanner Parameters
(n_)
(n_)
(n_)
(1)
(n_)
(n_)
(n_)
(n_)
(n_)
Coordinate Transformations
............................ 343
(n_)
(n_)
(n_)
(n_)
(n_)
(n_)
Online Positioning
(n_)
(n_)
(n_)
(n_)
(n_)
Status Monitoring and Diagnostics
(n_)
(n_)
(n_)
(n_)
(n_)
(n_)
(n_)
config_laser_signals ............................... 242
get_standby ............................................ 279
load_auto_laser_control ........................ 326
load_position_control ............................ 338
set_auto_laser_control ........................... 407
set_auto_laser_params .......................... 409
set_encoder_speed_ctrl ......................... 419
set_firstpulse_killer ................................ 423
set_laser_control .................................... 440
set_laser_mode ....................................... 443
set_laser_pulses_ctrl .............................. 445
set_pulse_picking ................................... 470
set_pulse_picking_length ...................... 470
set_qswitch_delay .................................. 471
set_softstart_level .................................. 484
set_softstart_mode ................................ 486
set_standby ............................................ 488
load_varpolydelay .................................. 346
set_delay_mode ..................................... 415
set_jump_speed_ctrl .............................. 439
set_mark_speed_ctrl .............................. 448
set_sky_writing ....................................... 477
set_sky_writing_limit ............................. 478
set_sky_writing_mode ........................... 479
set_sky_writing_para ............................. 481
set_angle ................................................ 405
(2)
set_defocus ....................................... 414
set_matrix ............................................... 449
set_offset ................................................ 463
(2)
set_offset_xyz ................................... 464
set_scale .................................................. 474
(1)
apply_mcbsp .......................................... 230
set_mcbsp_matrix .................................. 454
set_mcbsp_rot ........................................ 457
set_mcbsp_x ........................................... 458
set_mcbsp_y ........................................... 459
get_head_status ..................................... 266
get_overrun ............................................ 276
get_value ................................................ 291
get_values ............................................... 293
get_waveform ........................................ 294
measurement_status .............................. 365
stop_trigger ............................................ 524
(1)
(1)
(1)
(1)
220