Alcatel-Lucent OmniSwitch 6850-48 Cli Reference Manual page 3675

no ip route-map route-map-name [sequence-number number] match ipv4-interface interface-
name
ip route-map route-map-name [sequence-number number] match ipv6-interface interface-
name
no ip route-map route-map-name [sequence-number number] match ipv6-interface interface-
name
ip route-map route-map-name [sequence-number number] match metric metric [deviation
deviation]
no ip route-map route-map-name [sequence-number number] match metric metric
[deviation deviation]
ip route-map route-map-name [sequence-number number] match route-type {
external [type1 | type2] | level1 | level2
no ip route-map route-map-name [sequence-number number] match route-type {
external [type1 | type2] | level1 | level2
ip route-map route-map-name [sequence-number number] set metric metric
[effect {add | subtract | replace | none}]
no ip route-map route-map-name [sequence-number number] set metric metric
[effect {add | subtract | replace | none}]
ip route-map route-map-name [sequence-number number] set metric-type
{internal | external [type1 | type2]}
no ip route-map route-map-name [sequence-number number] set metric-type
{internal | external [type1 | type2]}
ip route-map route-map-name [sequence-number number] set tag tag-number
no ip route-map route-map-name [sequence-number number] set tag tag-number
ip route-map route-map-name [sequence-number number] set community community-string
no ip route-map route-map-name [sequence-number number] set community community-
string
ip route-map route-map-name [sequence-number number] set local-preference value
no ip route-map route-map-name [sequence-number number] set local-preference value
ip route-map route-map-name [sequence-number number] set level {level1 | level2 | level1-2}
no ip route-map route-map-name [sequence-number number] set level {level1 | level2 |
level1-2}
ip route-map route-map-name [sequence-number number] set ip-nexthop ip_address
no ip route-map route-map-name [sequence-number number] set ip-nexthop ip_address
ip route-map route-map-name [sequence-number number] set ipv6-nexthop ipv6_address
no ip route-map route-map-name [sequence-number number] set ipv6-nexthop ipv6_address
vrf [name | default]
no vrf name
arp ip_address hardware_address [alias] [arp-name name]
no arp ip_address [alias]
clear arp-cache
ip dos arp-poison restricted-address ip_address
no ip dos arp-poison restricted-address ip_address
arp filter ip_address [mask ip_mask] [vid] [sender | target] [allow | block]
OmniSwitch CLI Reference Guide
}
}
June 2012
no arp filter ip_address
clear arp filter
icmp type type code code {{enable | disable} | min-pkt-gap gap}
icmp unreachable [net-unreachable | host-unreachable | protocol-unreachable |
port-unreachable] {{enable | disable} | min-pkt-gap gap}
icmp echo [request | reply] {{enable | disable} | min-pkt-gap gap}
icmp timestamp [request | reply] {{enable | disable} | min-pkt-gap gap}
icmp addr-mask [request | reply] {{enable | disable} | min-pkt-gap gap}
icmp messages {enable | disable}
ip dos scan close-port-penalty penalty_value
internal |
ip dos scan tcp open-port-penalty penalty_value
ip dos scan udp open-port-penalty penalty_value
internal |
ip dos scan threshold threshold_value
ip dos trap {enable | disable}
ip dos scan decay decay_value
show ip traffic
show ip interface [name | emp | vlan vlan id | dhcp-client]
show ip managed-interface
show ip route [summary]
show ip route-pref
show ip redist [rip | ospf | bgp]
show ip access-list [access-list-name]
show ip route-map [route-map-name]
show ip router database [protocol type | gateway ip_address | dest {ip_address/prefixLen |
ip_address}]
show ip emp-route
show ip config
show ip protocols
show ip service
show ip dynamic-proxy-arp
show vrf
show arp [ip_address | hardware_address]
show arp summary
show arp filter [ip_address]
show icmp control
show icmp [statistics]
show tcp statistics
show tcp ports
show udp statistics
show udp ports
show ip dos config
show ip dos statistics
show ip dos arp-poison
ip wccp admin-state {enable | disable}
page 7 IP Commands