Alcatel-Lucent OmniSwitch 6850-48 Cli Reference Manual page 3670

link-fault-propagation group group_id wait-to-shutdown seconds
show link-fault-propagation group [group_id
interfaces slot/port tdr-test-start
interfaces {slot | slot/port[-port2]} no tdr-statistics
show interfaces [slot | slot/port[-port2]] tdr-statistics
UDLD Commands
udld {enable | disable}
]
udld port slot/port[-port2 {enable | disable}
[ ]]
udld port slot/port[-port2 mode {normal | aggressive}
[ ]]
udld port slot/port[-port2 probe-timer seconds
[ ]]
no udld port slot/port[-port2 probe-timer
[ ]]
udld port slot/port[-port2 echo-wait-timer seconds
[ ]]
no udld port slot/port[-port2 echo-wait-timer
clear udld statistics [port slot/port]
show udld configuration
show udld configuration port [slot/port
show udld statistics port slot/port
show udld neighbor port slot/port
]
show udld status port [slot/port
Power over Ethernet (PoE) Commands
]
lanpower start {slot/port[-port2 | slot}
] |
lanpower stop {slot/port[-port2
lanpower {slot/port | slot} power milliwatts
lanpower slot maxpower watts
lanpower slot/port priority {critical | high | low}
lanpower slot priority-disconnect {enable | disable}
lanpower slot slot-priority {critical | high | low}
lanpower redundant-power {enable | disable}
lanpower slot capacitor-detection {enable | disable}
show lanpower slot
show lanpower capacitor-detection slot
show lanpower priority-disconnect slot
show lanpower slot-priority slot
Source Learning Commands
mac-address-table [permanent] mac_address {slot/port | linkagg link_agg} vid [bridging |
filtering]
no mac-address-table [permanent | learned] [mac_address {slot/port |
mac-address-table vpls service-id permanent mac-address sap {sap-id | linkagg sap-id}
OmniSwitch CLI Reference Guide
]
]
}
slot
linkagg
June 2012
no mac-address-table vpls service-id permanent mac-address
no mac-address-table vpls service-id learned [sap sap-id | linkagg sap-id] mac-address
mac-address-table vpls service-id permanent mac-address mesh-sdp sdp-id[:vc-id]
no mac-address-table vpls service-id permanent mac-address
no mac-address-table vpls service-id learned [mesh-sdp sdp-id[:vc-id]] mac-address
mac-address-table static-multicast multicast_address {slot1/port1[-port1a] [slot2/port2[-
port2a]...] |
no mac-address-table static-multicast [multicast_address {slot1/port1[-port1a] [slot2/port2[-
port2a]...] |
mac-address-table aging-time seconds
no mac-address-table aging-time
source-learning {port slot/port1
source-learning chassis-distributed {enable | disable}
show mac-address-table [permanent | learned | quarantined] [mac_address] [slot slot | slot/
port] [linkagg link_agg] [vid | vid1-vid2]
show mac-address-table all [permanent | learned]
show mac-address-table vpls [service-id] [permanent | learned] [mac-address]
show mac-address-table vpls service-id sap {sap-id | linkagg sap-id} mac-address
show mac-address-table vpls service-id mesh-sdp sdp-id[:vc-id] mac-address
show mac-address-table static-multicast [multicast_address] [slot slot | slot/port] [linkagg
link_agg] [vid | vid1-vid2]
show mac-address-table count [mac_address] [slot slot | slot/port] [linkagg link_agg] [vid |
vid1-vid2]
show mac-address-table vpls service-id count] [mac-address]
show mac-address-table all count
show mac-address-table aging-time
show source-learning [port slot/port
show source-learning chassis-distributed
VLAN Management Commands
[
vlan vid1 -vid2
[
no vlan vid1 -vid2
[
vlan vid1 -vid2
[
vlan vid1 -vid2
vlan vid authentication {enable | disable}
vlan vid mtu-ip size
vlan vid port default {slot/port | link_agg}
vlan vid no port default {slot/port | link_agg}
show vlan [vid1
show vlan [vid1
show vlan router mac status
show vlan gvrp
link_agg} vid]
show vlan ipmvlan [ipmvlan-id1
page 2
linkagg
link_agg} vid
linkagg
link_agg} vid]
[ ] linkagg
-port2 | linkagg_num
[ ]
-port2 | linkagg linkagg_num
]
[enable | disable] [name description]
]
]
[1x1 | flat] stp {enable | disable}
]
mobile-tag {enable | disable}
[
-vid2]]
[
-vid2]] port [slot/port | link_agg]
[
[vid1 -vid2]]
[ ]]
-ipmvlan-id2
} {enable | disable}
]
UDLD Commands